1G/2.5G/5G/10G Multi-rate Ethernet PHY Intel® Stratix® 10 FPGA IP User Guide

Download PDF
ID 683876
Date 11/15/2021
Public
Document Table of Contents
Document Table of Contents x
1. About the 1G/2.5G/5G/10G Multi-rate Ethernet PHY Intel® FPGA IP Core 2. Getting Started 3. Parameter Settings 4. Functional Description 5. Configuration Registers 6. Interface Signals 7. 1G/2.5G/5G/10G Multi-rate Ethernet PHY Intel® Stratix® 10 FPGA IP User Guide Archives A. Document Revision History for the 1G/2.5G/5G/10G Multi-rate Ethernet PHY Intel® Stratix® 10 FPGA IP User Guide
1. About the 1G/2.5G/5G/10G Multi-rate Ethernet PHY Intel® FPGA IP Core x
1.1. Features 1.2. Device Family Support 1.3. Device Speed Grade Support 1.4. Resource Utilization 1.5. Release Information
2. Getting Started x
2.1. Installing and Licensing Intel® FPGA IP Cores 2.2. Specifying the IP Core Parameters and Options 2.3. Generated File Structure 2.4. Integrating Your IP Core in Your Design
2.1. Installing and Licensing Intel® FPGA IP Cores x
2.1.1. Intel® FPGA IP Evaluation Mode
2.4. Integrating Your IP Core in Your Design x
2.4.1. Pin Assignments 2.4.2. Adding the Transceiver PLL 2.4.3. Adding the Intel® Stratix® 10 Transceiver PHY Reset Controller
4. Functional Description x
4.1. Clocking and Reset Sequence 4.2. Timing Constraints 4.3. Switching Operation Speed
5. Configuration Registers x
5.1. Register Map 5.2. Register Definitions
6. Interface Signals x
6.1. Clock and Reset Signals 6.2. Transceiver Mode and Operating Speed Signals 6.3. Serial Interface Signals 6.4. GMII Signals 6.5. XGMII Signals 6.6. Avalon® -MM Interface Signals 6.7. Transceiver Status and Reconfiguration Signals 6.8. Status Signals
1. About the 1G/2.5G/5G/10G Multi-rate Ethernet PHY Intel® FPGA IP Core
2. Getting Started
3. Parameter Settings
4. Functional Description
5. Configuration Registers
6. Interface Signals
7. 1G/2.5G/5G/10G Multi-rate Ethernet PHY Intel® Stratix® 10 FPGA IP User Guide Archives
A. Document Revision History for the 1G/2.5G/5G/10G Multi-rate Ethernet PHY Intel® Stratix® 10 FPGA IP User Guide

6.2. Transceiver Mode and Operating Speed Signals

Table 17.  Transceiver Mode and Operating Speed Signals
Signal Name Direction Width Description PHY configurations
xcvr_mode Input 2 Connect this signal to the reconfiguration block. Use the following values to set the speed:
  • 0x0 = 1G
  • 0x1 = 2.5G
  • 0x3 = 10G
  • 2.5G
  • 1G/2.5G
  • 10M/100M/1G/2.5G
  • 1G/2.5G/10G (MGBASE-T)
  • 10M/100M/1G/2.5G/10G (MGBASE-T)
operating_speed Output 3 Connect this signal to the MAC. This signal provides the current operating speed of the PHY:
  • 0x0 = 10G
  • 0x1 = 1G
  • 0x2 = 100M
  • 0x3 = 10M
  • 0x4 = 2.5G
  • 0x5 = 5G
 All
Level Two Title