CPRI Intel® FPGA IP User Guide

Download PDF
ID 683595
Date 7/01/2022
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. About the CPRI Intel® FPGA IP Core 2. Getting Started with the CPRI Intel® FPGA IP Core 3. Functional Description 4. CPRI Intel® FPGA IP Core Signals 5. CPRI Intel® FPGA IP Core Registers A. Additional Information
1. About the CPRI Intel® FPGA IP Core x
1.1. CPRI Intel® FPGA IP Core Supported Features 1.2. CPRI Intel® FPGA IP Core Device Family and Speed Grade Support 1.3. Intel® FPGA IP Core Verification 1.4. Resource Utilization for CPRI Intel® FPGA IP Core 1.5. Release Information
1.2. CPRI Intel® FPGA IP Core Device Family and Speed Grade Support x
1.2.1. Device Family Support 1.2.2. CPRI Intel® FPGA IP Core Performance: Device and Transceiver Speed Grade Support
2. Getting Started with the CPRI Intel® FPGA IP Core x
2.1. Installation and Licensing 2.2. Generating CPRI Intel® FPGA IP Core 2.3. CPRI Intel® FPGA IP File Structure 2.4. CPRI Intel® FPGA IP Core Parameters 2.5. Integrating Your Intel® FPGA IP Core in Your Design: Required External Blocks 2.6. Simulating Intel FPGA IP Cores 2.7. Understanding the Testbench 2.8. Running the Design Example 2.9. Compiling the Full Design and Programming the FPGA
2.1. Installation and Licensing x
2.1.1. Intel® FPGA IP Evaluation Mode
2.5. Integrating Your Intel® FPGA IP Core in Your Design: Required External Blocks x
2.5.1. Adding the Transceiver TX PLL IP Core 2.5.2. Adding the Reset Controller 2.5.3. Adding the Transceiver Reconfiguration Controller 2.5.4. Adding the Off-Chip Clean-Up PLL 2.5.5. Adding and Connecting the Single-Trip Delay Calibration Blocks 2.5.6. Transceiver PLL Calibration 2.5.7. Reference and System PLL Clock for your IP Design
3. Functional Description x
3.1. Interfaces Overview 3.2. CPRI Intel® FPGA IP Core Clocking Structure 3.3. CPRI Intel® FPGA IP Core Reset Requirements 3.4. Start-Up Sequence Following Reset 3.5. AUX Interface 3.6. Direct IQ Interface 3.7. Ctrl_AxC Interface 3.8. Direct Vendor Specific Access Interface 3.9. Real-Time Vendor Specific Interface 3.10. Direct HDLC Serial Interface 3.11. Direct L1 Control and Status Interface 3.12. L1 Debug Interface 3.13. Media Independent Interface (MII) to External Ethernet Block 3.14. Gigabit Media Independent Interface (GMII) to External Ethernet Block 3.15. CPU Interface to CPRI Intel® FPGA IP Registers 3.16. Auto-Rate Negotiation 3.17. Extended Delay Measurement 3.18. Deterministic Latency and Delay Measurement and Calibration 3.19. CPRI Intel® FPGA IP Transceiver and Transceiver Management Interfaces 3.20. Testing Features
3.2. CPRI Intel® FPGA IP Core Clocking Structure x
3.2.1. Example CPRI Intel® FPGA IP Core Clock Connections in Different Clocking Modes
3.4. Start-Up Sequence Following Reset x
3.4.1. Start-Up Sequence Interface Signals
3.5. AUX Interface x
3.5.1. AUX Interface Signals 3.5.2. AUX Interface Synchronization 3.5.3. Auxiliary Latency Cycles 3.5.4. Direct Interface CPRI Frame Data Format
3.15. CPU Interface to CPRI Intel® FPGA IP Registers x
3.15.1. CPU Interface Signals 3.15.2. Accessing the Hyperframe Control Words
3.15.2. Accessing the Hyperframe Control Words x
3.15.2.1. Specifying the Control Word 3.15.2.2. Specifying the Position in the Control Word 3.15.2.3. Retrieving the Hyperframe Control Words 3.15.2.4. Writing the Hyperframe Control Words
3.17. Extended Delay Measurement x
3.17.1. Extended Delay Measurement for Soft Internal Buffers 3.17.2. Extended Delay Measurement for Intel® Stratix® 10 Hard FIFOs 3.17.3. Extended Delay Measurement Interface
3.18. Deterministic Latency and Delay Measurement and Calibration x
3.18.1. Delay Measurement and Calibration Features 3.18.2. Delay Requirements 3.18.3. Single-Hop Delay Measurement 3.18.4. Multi-Hop Delay Measurement 3.18.5. Delay Calibration Features
3.18.3. Single-Hop Delay Measurement x
3.18.3.1. Rx Path Delay 3.18.3.2. Tx Path Delay 3.18.3.3. Round-Trip Delay
3.18.5. Delay Calibration Features x
3.18.5.1. Single-Trip Delay Calibration 3.18.5.2. Round-Trip Delay Calibration 3.18.5.3. Tx Bitslip Delay
3.18.5.1. Single-Trip Delay Calibration x
3.18.5.1.1. Single-Trip Latency Measurement and Calibration Interface Signals
3.19. CPRI Intel® FPGA IP Transceiver and Transceiver Management Interfaces x
3.19.1. CPRI Link 3.19.2. Main Transceiver Clock and Reset Signals 3.19.3. Arria V, Arria V GZ, Cyclone V, and Stratix V Transceiver Reconfiguration Interface 3.19.4. Intel® Arria® 10, Intel® Stratix® 10, and Intel® Agilex™ Transceiver Reconfiguration Interface 3.19.5. RS-FEC Interface 3.19.6. Interface to the External Reset Controller 3.19.7. Interface to the External PLL 3.19.8. Transceiver Debug Interface
3.20. Testing Features x
3.20.1. CPRI Intel® FPGA IP Core Loopback Modes 3.20.2. CPRI Intel® FPGA IP Core Self-Synchronization Feature
4. CPRI Intel® FPGA IP Core Signals x
4.1. CPRI Intel® FPGA IP Core L2 Interface 4.2. CPRI Intel® FPGA IP Core L1 Direct Access Interfaces 4.3. CPRI Intel® FPGA IP Core Management Interfaces 4.4. CPRI Intel® FPGA IP Core Transceiver and Transceiver Management Signals
A. Additional Information x
A.1. CPRI Intel® FPGA IP User Guide Archives A.2. Document Revision History for the CPRI Intel® FPGA IP User Guide
1. About the CPRI Intel® FPGA IP Core
2. Getting Started with the CPRI Intel® FPGA IP Core
3. Functional Description
4. CPRI Intel® FPGA IP Core Signals
5. CPRI Intel® FPGA IP Core Registers
A. Additional Information

3.20.2. CPRI Intel® FPGA IP Core Self-Synchronization Feature

Intel® provides a self-synchronization testing feature that supports an RE slave in a CPRI link external loopback configuration. This feature is intended to work correctly only for Layer 1 testing.

By default, only an REC master can function correctly in a CPRI link external loopback configuration. An RE slave in external loopback configuration cannot achieve frame synchronization, because the CPRI RX interface must lock on to the K28.5 character before the CPRI TX interface can begin sending K28.5 characters. Therefore, no K28.5 character is ever transmitted on the RE slave loopback CPRI link.

However, in an RE slave CPRI IP you can specify that the CPRI TX interface begin sending K28.5 characters before the CPRI Rx interface locks on to the K28.5 character from the CPRI link. This feature supports a CPRI RE slave in achieving frame synchronization without being connected to a CPRI master, and allows you to test your CPRI RE slave without the need for an additional CPRI IP.

To turn on this feature, connect your CPRI RE slave in a CPRI link external loopback configuration, and set the tx_enable_force field of the L1_CONFIG register to the value of 1.

Level Two Title