High Bandwidth Memory (HBM2) Interface FPGA IP User Guide

Download PDF
ID 683189
Date 3/29/2024
Public
Document Table of Contents
Document Table of Contents x
1. About the High Bandwidth Memory (HBM2) Interface Intel® FPGA IP 2. Introduction to High Bandwidth Memory 3. Stratix® 10 HBM2 Architecture 4. Creating and Parameterizing the High Bandwidth Memory (HBM2) Interface Intel® FPGA IP 5. Simulating the High Bandwidth Memory (HBM2) Interface Intel® FPGA IP 6. High Bandwidth Memory (HBM2) Interface Intel® FPGA IP Interface 7. High Bandwidth Memory (HBM2) Interface Intel® FPGA IP Controller Performance 8. High Bandwidth Memory (HBM2) Interface Intel® FPGA IP User Guide Archives 9. Document Revision History for High Bandwidth Memory (HBM2) Interface FPGA IP User Guide
1. About the High Bandwidth Memory (HBM2) Interface Intel® FPGA IP x
1.1. Release Information
2. Introduction to High Bandwidth Memory x
2.1. HBM2 in Intel® Stratix® 10 Devices 2.2. HBM2 DRAM Structure 2.3. Stratix® 10 HBM2 Features 2.4. Stratix® 10 HBM2 Controller Features
3. Stratix® 10 HBM2 Architecture x
3.1. Stratix® 10 HBM2 Introduction 3.2. Stratix® 10 UIB Architecture 3.3. Stratix® 10 HBM2 Controller Architecture
3.3. Stratix® 10 HBM2 Controller Architecture x
3.3.1. Stratix® 10 HBM2 Controller Details
4. Creating and Parameterizing the High Bandwidth Memory (HBM2) Interface Intel® FPGA IP x
4.1. Creating an Quartus® Prime Pro Edition Project for High Bandwidth Memory (HBM2) Interface FPGA IP 4.2. Parameterizing the High Bandwidth Memory (HBM2) Interface Intel® FPGA IP 4.3. Pin Planning for the High Bandwidth Memory (HBM2) Interface Intel® FPGA IP
4.2. Parameterizing the High Bandwidth Memory (HBM2) Interface Intel® FPGA IP x
4.2.1. General Parameters for High Bandwidth Memory (HBM2) Interface Intel® FPGA IP 4.2.2. FPGA I/O Parameters for High Bandwidth Memory (HBM2) Interface Intel® FPGA IP 4.2.3. Controller Parameters for High Bandwidth Memory (HBM2) Interface Intel® FPGA IP 4.2.4. Diagnostic Parameters for High Bandwidth Memory (HBM2) Interface Intel® FPGA IP 4.2.5. Example Designs Parameters for High Bandwidth Memory (HBM2) Interface Intel® FPGA IP 4.2.6. Register Map IP-XACT Support for HBM2 IP
5. Simulating the High Bandwidth Memory (HBM2) Interface Intel® FPGA IP x
5.1. High Bandwidth Memory (HBM2) Interface Intel® FPGA IP Example Design 5.2. Simulating High Bandwidth Memory (HBM2) Interface Intel® FPGA IP with ModelSim* and Questa* 5.3. Simulating High Bandwidth Memory (HBM2) Interface Intel® FPGA IP with Synopsys VCS* 5.4. Simulating High Bandwidth Memory (HBM2) Interface Intel® FPGA IP with Riviera-PRO* 5.5. Simulating High Bandwidth Memory (HBM2) Interface Intel® FPGA IP with Cadence Xcelium* Parallel Simulator 5.6. Simulating High Bandwidth Memory (HBM2) Interface Intel® FPGA IP for High Efficiency 5.7. Simulating High Bandwidth Memory (HBM2) Interface IP Instantiated in Your Project
6. High Bandwidth Memory (HBM2) Interface Intel® FPGA IP Interface x
6.1. High Bandwidth Memory (HBM2) Interface Intel® FPGA IP High Level Block Diagram 6.2. High Bandwidth Memory (HBM2) Interface Intel® FPGA IP Controller Interface Signals 6.3. User AXI Interface Timing 6.4. User APB Interface Timing 6.5. User-controlled Accesses to the HBM2 Controller 6.6. Soft AXI Switch
6.2. High Bandwidth Memory (HBM2) Interface Intel® FPGA IP Controller Interface Signals x
6.2.1. Clock Signals 6.2.2. Reset Signals 6.2.3. Calibration Status Signals 6.2.4. Memory Interface Signals 6.2.5. User-interface Signals 6.2.6. AXI User-interface Signals 6.2.7. Sideband APB Interface 6.2.8. Avalon® Memory-Mapped (AVMM) Interface Signals
6.3. User AXI Interface Timing x
6.3.1. AXI Write Transaction 6.3.2. AXI Read Transaction 6.3.3. Improving User Logic to HBM2 Controller AXI Interface Timing
6.4. User APB Interface Timing x
6.4.1. Advanced Peripheral Bus Protocol 6.4.2. APB Interface Timing
6.5. User-controlled Accesses to the HBM2 Controller x
6.5.1. User-controlled Refreshes 6.5.2. Temperature and Calibration Status Readout 6.5.3. Controller Idle State Status 6.5.4. Power Down Status 6.5.5. ECC Error Status 6.5.6. User Interrupt 6.5.7. ECC Error Correction and Detection
6.5.6. User Interrupt x
6.5.6.1. Interrupt Enable and Conditions for Interrupt Generation 6.5.6.2. Interrupt Status 6.5.6.3. Error Valid Status
6.6. Soft AXI Switch x
6.6.1. AXI Switch Selection in HBM2 IP Catalog GUI
7. High Bandwidth Memory (HBM2) Interface Intel® FPGA IP Controller Performance x
7.1. High Bandwidth Memory (HBM2) DRAM Bandwidth 7.2. High Bandwidth Memory (HBM2) Interface Intel® FPGA IP HBM2 IP Efficiency 7.3. High Bandwidth Memory (HBM2) Interface Intel® FPGA IP Latency 7.4. High Bandwidth Memory (HBM2) Interface Intel® FPGA IP Timing 7.5. High Bandwidth Memory (HBM2) Interface Intel® FPGA IP DRAM Temperature Readout
1. About the High Bandwidth Memory (HBM2) Interface Intel® FPGA IP
2. Introduction to High Bandwidth Memory
3. Stratix® 10 HBM2 Architecture
4. Creating and Parameterizing the High Bandwidth Memory (HBM2) Interface Intel® FPGA IP
5. Simulating the High Bandwidth Memory (HBM2) Interface Intel® FPGA IP
6. High Bandwidth Memory (HBM2) Interface Intel® FPGA IP Interface
7. High Bandwidth Memory (HBM2) Interface Intel® FPGA IP Controller Performance
8. High Bandwidth Memory (HBM2) Interface Intel® FPGA IP User Guide Archives
9. Document Revision History for High Bandwidth Memory (HBM2) Interface FPGA IP User Guide

5.2. Simulating High Bandwidth Memory (HBM2) Interface Intel® FPGA IP with ModelSim* and Questa*

  1. Launch the ModelSim simulator.
  2. Select File > Change Directoryand navigate to: project_directory/sim/ed_sim/sim/mentor
  3. Verify that the Transcript window is visible; if it is not, display it by selecting View > Transcript.
  4. In the Transcript window, run source msim_setup.tcl at the bottom of the ModelSim tool screen.
  5. After the Tcl script finishes running, run ld_debug in the Transcript window. This command compiles the design files and elaborates the top-level design.
  6. After ld_debug finishes running, the Objects window appears. In the Objects window, select the signals to simulate by right-clicking and selecting Add Wave from the context menu.
    For example, if you want to see the HBM2 interface signals, select the module mem0_0 from the Instance window. With mem0_0 selected, go to the Objects window and select the signals that you want to see. (If the Objects window is not visible, you can display it by selecting View > Objects.
  7. To run the HBM2 simulation, type run -all.
    If the simulation is not visible, select View > Wave. With the Wave window open, select File > Save Format. Click OK to capture your selected waveforms in a wave.do file. To display the waveforms, type do wave.do, and then type run -all.
    Whenever you make changes to the design or to the wave.do, you must repeat step 7 of this procedure. Alternatively, you can combine the instructions into a script and run that script instead. The following example illustrates a run.do script containing the necessary commands: 
    if {[file exists msim_setup.tcl]} {
        source msim_setup.tcl
       ld_debug
        do wave.do
       run -all } else {        error "The msim_setup.tcl script does not exist. 
Please generate the example design RTL and simulation scripts. See ../../README.txt 
for help." }
    Save the run.do script in the same directory as the msim_setup.tcl file. Type do run.do to run this script from the Transcript window.
  8. Upon completion of the simulation, the Transcript window displays efficiency data and other useful information.
Level Two Title