Agilex™ 7 FPGA F-Series (2 × F-Tiles) Development Kit User Guide

Download PDF
ID 739942
Date 12/20/2024
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Getting Started 3. Development Kit Setup 4. Board Test System 5. Development Kit Hardware and Configuration 6. Custom Projects for the Development Kit 7. Document Revision History for the Agilex™ 7 FPGA F-Series (2 × F-Tiles) Development Kit User Guide A. Development Kit Components B. Developer Resources C. Safety and Regulatory Compliance Information
1. Overview x
1.1. Block Diagram 1.2. Feature Summary 1.3. Box Contents 1.4. Recommended Operating Conditions
2. Getting Started x
2.1. Before You Begin 2.2. Handling the Board 2.3. Quartus® Prime Software and Driver Installation
2.3. Quartus® Prime Software and Driver Installation x
2.3.1. Installing the Quartus® Prime Pro Edition Software 2.3.2. Installing the Development Kit 2.3.3. Installing the Intel® FPGA Download Cable II Driver
3. Development Kit Setup x
3.1. Default Settings 3.2. Powering Up the Development Board
4. Board Test System x
4.1. Set Up BTS GUI Running Environment 4.2. Test the Functionality of the Development Kit 4.3. Control On-Board Clock through Clock Controller GUI 4.4. Monitor On-Board Power Regulator through Power Monitor GUI 4.5. BTS Test Areas 4.6. Identify Test Pass or Fail based on BTS GUI Test Status
4.1. Set Up BTS GUI Running Environment x
4.1.1. Downloading OpenJDK 4.1.2. Downloading OpenJFX 4.1.3. Installing OpenJDK and OpenJFX 4.1.4. Setting Up the Quartus® Prime Software for BTS Operation 4.1.5. Running the BTS GUI
4.2. Test the Functionality of the Development Kit x
4.2.1. The Bottom Info Bar 4.2.2. The Configure Menu 4.2.3. The Sys Info Tab 4.2.4. The GPIO Tab 4.2.5. The XCVR Tab 4.2.6. The Memory Tab
4.2.5. The XCVR Tab x
4.2.5.1. The QSFP NRZ Tab 4.2.5.2. The QSFP PAM4 Tab 4.2.5.3. The QSFPDD NRZ Tab 4.2.5.4. The QSFPDD PAM4 Tab
5. Development Kit Hardware and Configuration x
5.1. JTAG Configuration Mode 5.2. Active Serial (AS) x4 Configuration Mode 5.3. Avalon® Streaming Interface x16 Configuration Mode
6. Custom Projects for the Development Kit x
6.1. Add SmartVID Settings in the Quartus® Prime QSF File 6.2. Golden Top
A. Development Kit Components x
A.1. Board Overview and Components A.2. FPGA Configuration A.3. Default Switch and Jumper Settings A.4. Input and Output Components A.5. Components and Interfaces A.6. I2C A.7. MAX® 10 SPI Bus A.8. Clock Circuits A.9. HPS Daughter Card A.10. System Power A.11. Power Guidelines A.12. Power Distribution System A.13. Power Measurement A.14. Thermal Limitations and Protection
A.1. Board Overview and Components x
A.1.1. Board Overview A.1.2. Board Components A.1.3. MAX® 10 CPLD System Controller
A.2. FPGA Configuration x
A.2.1. Programming the FPGA over On-Board Intel® FPGA Download Cable II A.2.2. Programming the FPGA over an External Intel® FPGA Download Cable II
A.3. Default Switch and Jumper Settings x
A.3.1. Switch Description A.3.2. Jumper Description
A.4. Input and Output Components x
A.4.1. Push Buttons A.4.2. Switches A.4.3. LEDs
A.5. Components and Interfaces x
A.5.1. PCI Express* ( PCIe* ) Interface A.5.2. QSFP-DD Interface A.5.3. QSFP Interface A.5.4. CXL Interface A.5.5. DDR4 DIMM1 Interface A.5.6. DDR4 DIMM2 Interface A.5.7. DDR4 Component Interface A.5.8. HPS IO48 Interface
A.11. Power Guidelines x
A.11.1. In a Standard PCIe* -Compliant System A.11.2. As a Standalone Evaluation Board Powered by Included Power Supply
C. Safety and Regulatory Compliance Information x
C.1. Safety and Regulatory Information C.2. Compliance Information
C.1. Safety and Regulatory Information x
C.1.1. Safety Warnings C.1.2. Safety Cautions
1. Overview
2. Getting Started
3. Development Kit Setup
4. Board Test System
5. Development Kit Hardware and Configuration
6. Custom Projects for the Development Kit
7. Document Revision History for the Agilex™ 7 FPGA F-Series (2 × F-Tiles) Development Kit User Guide
A. Development Kit Components
B. Developer Resources
C. Safety and Regulatory Compliance Information

A.3.2. Jumper Description

In the Avalon® streaming interface x16 configuration mode, the board provides one QSPI flash for storing up to four configuration images. The configuration of the FPGA with one of these images is managed by the MAX® 10, depending on the selection of jumpers J105 and J106.

Table 24.  Selected Configuration Image
J106 J105 Selected Configuration Image
ON ON Image 0 (Default)
ON OFF Image 1
OFF ON Image 2
OFF OFF Image 3
Level Two Title