Intel® Quartus® Prime Pro Edition User Guide: Timing Analyzer

Download PDF
ID 683243
Date 3/28/2022
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. Answers to Top FAQs 2. Timing Analysis Introduction 3. Using the Intel® Quartus® Prime Timing Analyzer A. Intel® Quartus® Prime Pro Edition User Guides
2. Timing Analysis Introduction x
2.1. What's New In This Version 2.2. Timing Analysis Basic Concepts 2.3. Timing Analysis Overview Document Revision History
2.2. Timing Analysis Basic Concepts x
2.2.1. Timing Path and Clock Analysis 2.2.2. Clock Setup Analysis 2.2.3. Clock Hold Analysis 2.2.4. Recovery and Removal Analysis 2.2.5. Multicycle Path Analysis 2.2.6. Metastability Analysis 2.2.7. Timing Pessimism 2.2.8. Clock-As-Data Analysis 2.2.9. Multicorner Timing Analysis 2.2.10. Time Borrowing
2.2.1. Timing Path and Clock Analysis x
2.2.1.1. The Timing Netlist 2.2.1.2. Timing Paths 2.2.1.3. Data and Clock Arrival Times 2.2.1.4. Launch and Latch Edges
2.2.5. Multicycle Path Analysis x
2.2.5.1. Multicycle Clock Hold 2.2.5.2. Multicycle Clock Setup
2.2.10. Time Borrowing x
2.2.10.1. Time Borrowing Limitations 2.2.10.2. Time Borrowing with Latches
3. Using the Intel® Quartus® Prime Timing Analyzer x
3.1. Timing Analysis Flow 3.2. Step 1: Specify Timing Analyzer Settings 3.3. Step 2: Specify Timing Constraints 3.4. Step 3: Run the Timing Analyzer 3.5. Step 4: Analyze Timing Reports 3.6. Applying Timing Constraints 3.7. Timing Analyzer Tcl Commands 3.8. Timing Analysis of Imported Compilation Results 3.9. Using the Intel® Quartus® Prime Timing Analyzer Document Revision History 3.10. Intel® Quartus® Prime Pro Edition User Guide: Timing Analyzer Archive
3.4. Step 3: Run the Timing Analyzer x
3.4.1. Setting the Operating Conditions 3.4.2. Enabling Time Borrowing Optimization
3.5. Step 4: Analyze Timing Reports x
3.5.1. Generating Timing Reports 3.5.2. Cross-Probing with Design Assistant 3.5.3. Launching Design Assistant from Timing Analyzer 3.5.4. Locating Timing Paths in Other Tools 3.5.5. Correlating Constraints to the Timing Report
3.5.1. Generating Timing Reports x
3.5.1.1. Report Fmax Summary 3.5.1.2. Report Timing 3.5.1.3. Report Timing By Source Files 3.5.1.4. Report Data Delay 3.5.1.5. Report Net Delay 3.5.1.6. Report Clocks and Clock Network 3.5.1.7. Report Clock Transfers 3.5.1.8. Report Metastability 3.5.1.9. Report CDC Viewer 3.5.1.10. Report Asynchronous CDC 3.5.1.11. Report Logic Depth 3.5.1.12. Report Neighbor Paths 3.5.1.13. Report Register Spread 3.5.1.14. Report Route Net of Interest 3.5.1.15. Report Retiming Restrictions 3.5.1.16. Report Reset Statistics 3.5.1.17. Report Pipelining Information 3.5.1.18. Report Time Borrowing Data 3.5.1.19. Report Exceptions and Exceptions Reachability 3.5.1.20. Report Bottlenecks
3.5.1.13. Report Register Spread x
3.5.1.13.1. Registers with High Timing Path Endpoint Tension 3.5.1.13.2. Registers with High Immediate Fan-Out Tension
3.5.1.20. Report Bottlenecks x
3.5.1.20.1. Specifying Custom Bottleneck Criteria
3.5.2. Cross-Probing with Design Assistant x
3.5.2.1. Cross-Probing from Design Assistant to Timing Analyzer
3.6. Applying Timing Constraints x
3.6.1. Recommended Initial SDC Constraints 3.6.2. SDC File Precedence 3.6.3. Modifying Iterative Constraints 3.6.4. Using Entity-bound SDC Files 3.6.5. Creating Clocks and Clock Constraints 3.6.6. Creating I/O Constraints 3.6.7. Creating Delay and Skew Constraints 3.6.8. Creating Timing Exceptions 3.6.9. Using Fitter Overconstraints 3.6.10. Example Circuit and SDC File
3.6.1. Recommended Initial SDC Constraints x
3.6.1.1. Create Clock (create_clock) 3.6.1.2. Derive PLL Clocks (derive_pll_clocks) 3.6.1.3. Derive Clock Uncertainty (derive_clock_uncertainty) 3.6.1.4. Set Clock Groups (set_clock_groups)
3.6.4. Using Entity-bound SDC Files x
3.6.4.1. Entity-bound Constraint Scope 3.6.4.2. Entity-bound Constraint Examples
3.6.5. Creating Clocks and Clock Constraints x
3.6.5.1. Creating Base Clocks 3.6.5.2. Creating Virtual Clocks 3.6.5.3. Creating Generated Clocks (create_generated_clock) 3.6.5.4. Deriving PLL Clocks 3.6.5.5. Creating Clock Groups (set_clock_groups) 3.6.5.6. Accounting for Clock Effect Characteristics 3.6.5.7. Constraining CDC Paths
3.6.5.1. Creating Base Clocks x
3.6.5.1.1. Automatic Clock Detection and Constraint Creation
3.6.5.2. Creating Virtual Clocks x
3.6.5.2.1. Specifying I/O Interface Uncertainty 3.6.5.2.2. I/O Interface Clock Uncertainty Example
3.6.5.3. Creating Generated Clocks (create_generated_clock) x
3.6.5.3.1. Clock Divider Example (-divide_by) 3.6.5.3.2. Clock Multiplexer Example
3.6.5.5. Creating Clock Groups (set_clock_groups) x
3.6.5.5.1. Exclusive Clock Groups (-logically_exclusive or -physically_exclusive) 3.6.5.5.2. Asynchronous Clock Groups (-asynchronous) 3.6.5.5.3. set_clock_groups Constraint Tips
3.6.5.6. Accounting for Clock Effect Characteristics x
3.6.5.6.1. Set Clock Latency (set_clock_latency) 3.6.5.6.2. Clock Uncertainty
3.6.6. Creating I/O Constraints x
3.6.6.1. Input Constraints (set_input_delay) 3.6.6.2. Output Constraints (set_output_delay)
3.6.7. Creating Delay and Skew Constraints x
3.6.7.1. Advanced I/O Timing and Board Trace Model Delay 3.6.7.2. Maximum Skew (set_max_skew) 3.6.7.3. Net Delay (set_net_delay)
3.6.8. Creating Timing Exceptions x
3.6.8.1. Timing Exception Precedence 3.6.8.2. False Paths (set_false_path) 3.6.8.3. Minimum and Maximum Delays 3.6.8.4. Multicycle Paths 3.6.8.5. Multicycle Exception Examples 3.6.8.6. Delay Annotation 3.6.8.7. Constraining Design Partition Ports
3.6.8.4. Multicycle Paths x
3.6.8.4.1. Common Multicycle Applications 3.6.8.4.2. Relaxing Setup with Multicycle (set_multicyle_path) 3.6.8.4.3. Accounting for a Phase Shift (-phase)
3.6.8.5. Multicycle Exception Examples x
3.6.8.5.1. Default Multicycle Analysis 3.6.8.5.2. End Multicycle Setup = 2 and End Multicycle Hold = 0 3.6.8.5.3. End Multicycle Setup = 2 and End Multicycle Hold = 1 3.6.8.5.4. Same Frequency Clocks with Destination Clock Offset 3.6.8.5.5. Destination Clock Frequency is a Multiple of the Source Clock Frequency 3.6.8.5.6. Destination Clock Frequency is a Multiple of the Source Clock Frequency with an Offset 3.6.8.5.7. Source Clock Frequency is a Multiple of the Destination Clock Frequency 3.6.8.5.8. Source Clock Frequency is a Multiple of the Destination Clock Frequency with an Offset
3.7. Timing Analyzer Tcl Commands x
3.7.1. The quartus_sta Executable 3.7.2. Collection Commands
3.7.2. Collection Commands x
3.7.2.1. Wildcard Characters 3.7.2.2. Adding and Removing Collection Items 3.7.2.3. Query of Collections 3.7.2.4. Using the get_pins Command
1. Answers to Top FAQs
2. Timing Analysis Introduction
3. Using the Intel® Quartus® Prime Timing Analyzer
A. Intel® Quartus® Prime Pro Edition User Guides

3.6.5.7. Constraining CDC Paths

It is essential to apply timing constraints to the multibit clock domain crossing (CDC) paths in your design. You can use the following constraints to constrain CDC paths:

Attention: As of Intel® Quartus® Prime Pro Edition software version 21.3, the set_false_path constraint does not override the set_max_skew constraint. You can now apply the set_false_path and set_max_skew constraints on the same path without override.
Table 29.  CDC Path Constraints
Constraints Description

set_false_path

set_clock_group -asynchronous

Both constraints prevent the Compiler from optimizing slack between asynchronous domain crossings. set_clock_group is the most aggressive constraint.

  • Clock-based false paths are less aggressive because these constraints only cut timing on the from_clock to to_clock order specified.
  • Clock-based false paths are unlike clock groups that cut the path in both directions.
  • Path-based false paths are the most specific constraint because they cut only on the specified from and to nodes.
set_max_skew Sets a bound on the allowable skew between different bus bits.
  • Check the timing of your clock domain crossing by running the Report Max Skew Summary command.
  • The actual skew requirements depends on your design characteristics, and how you handle the clock domain crossing.

set_net_delay -max

set_data_delay

Sets a bound on the allowable datapath delay on any bit of a bus transfer.

  • set_net_delay is for constraining individual clock edges and nets. Run the Report Net Delay Summary command to report data for this constraint.
  • set_data_delay is for constraining entire paths. Run the Report Data Delay command to report data for this constraint.

The following shows example constraints for a clock domain crossing between data_a in clock domain clk_a, and data_b in clock domain clk_b: 

create_clock -name clk_a -period 4.000 [get_ports {clk_a}]
create_clock -name clk_b -period 4.500 [get_ports {clk_b}]
set_clock_groups -asynchronous -group [get_clocks {clk_a}] -group \
     [get_clocks {clk_b}]
set_net_delay -from [get_registers {data_a[*]}] -to [get_registers \
     {data_b[*]}] -max -get_value_from_clock_period \
     dst_clock_period -value_multiplier 0.8
set_max_skew -from [get_keepers {data_a[*]}] -to [get_keepers \
     {data_b[*]}] -get_skew_value_from_clock_period min_clock_period \
     -skew_value_multiplier 0.8

The following examples show applying set_false_path for a design that contains a DCFIFO block to avoid timing failures in the synchronization registers. These examples are for constraining single-bit synchronizer CDC paths:

  • For paths crossing from the write into the read domain, apply a false path assignment between registers delayed_wrptr_g and rs_dgwp:
    set_false_path -from [get_registers {*dcfifo*delayed_wrptr_g[*]}] \
-to [get_registers {*dcfifo*rs_dgwp*}]
  • For paths crossing from the read into the write domain, apply a false path assignment between registers rdptr_g and ws_dgrp:
    set_false_path -from [get_registers {*dcfifo*rdptr_g[*]}] \
-to [get_registers {*dcfifo*ws_dgrp*}]
Level Two Title