Thermal Design User Guide: Agilex™ 3 FPGAs and SoCs

Download PDF
ID 851249
Date 5/12/2025
Public
Document Table of Contents
Document Table of Contents x
1. Introduction to Agilex™ 3 FPGA Thermal Design Guidelines 2. Agilex™ 3 FPGA Mechanical Construction 3. Agilex™ 3 FPGA Compact Thermal Model (CTM) Construction 4. Power and Thermal Calculator (PTC) 5. Thermal Design Process 6. General FPGA Thermal Design Considerations 7. Design Examples 8. Heat Sinks 9. Document Revision History for the Thermal Design User Guide: Agilex™ 3 FPGAs and SoCs A. Agilex™ 3 FPGA Product Keys and Package Drawings
1. Introduction to Agilex™ 3 FPGA Thermal Design Guidelines x
1.1. Thermal Design Requirements 1.2. Thermal Design Flow 1.3. Definitions of Thermal and Power Terms Used in this Document
2. Agilex™ 3 FPGA Mechanical Construction x
2.1. Built-in Temperature Sensors
2.1. Built-in Temperature Sensors x
2.1.1. Agilex™ 3 FPGA Temperature Rating
3. Agilex™ 3 FPGA Compact Thermal Model (CTM) Construction x
3.1. CTM File Format 3.2. Thermal Modeling with the CTM 3.3. CTM Top Temperature, TCASE Virtual Sensor 3.4. Obtaining the CTM
4. Power and Thermal Calculator (PTC) x
4.1. PTC Thermal Tab Parameters 4.2. Thermal Analysis with the PTC 4.3. PTC Thermal Tab Calculation Options 4.4. Thermal Resistances and Low Power Devices 4.5. Sensor Temperatures on the PTC Thermal Tab
5. Thermal Design Process x
5.1. Package Heat Flow Path 5.2. Variables Affecting the Heat Flow Path 5.3. Recommended Thermal Design Method
6. General FPGA Thermal Design Considerations x
6.1. FPGA Power Considerations
6.1. FPGA Power Considerations x
6.1.1. FPGA Maximum Allowed Power Dissipation 6.1.2. Static, Dynamic, and Standby Power 6.1.3. Future-Proofing an FPGA Thermal Design
7. Design Examples x
7.1. Example 1: Find Cooling Solution for Maximum Junction Temperature Limit 7.2. Example 2: Find Available Thermal Margin for Cooling Solution 7.3. Example 3: Find the Ambient Temperature for a Specified Cooling Solution
8. Heat Sinks x
8.1. Attachment Force 8.2. Thermal Interface Material (TIM)
8.2. Thermal Interface Material (TIM) x
8.2.1. Common TIM2 Materials
8.2.1. Common TIM2 Materials x
8.2.1.1. TIM2 Performance Parameters And Challenges 8.2.1.2. Understanding Resistance and Pressure Map Curves
1. Introduction to Agilex™ 3 FPGA Thermal Design Guidelines
2. Agilex™ 3 FPGA Mechanical Construction
3. Agilex™ 3 FPGA Compact Thermal Model (CTM) Construction
4. Power and Thermal Calculator (PTC)
5. Thermal Design Process
6. General FPGA Thermal Design Considerations
7. Design Examples
8. Heat Sinks
9. Document Revision History for the Thermal Design User Guide: Agilex™ 3 FPGAs and SoCs
A. Agilex™ 3 FPGA Product Keys and Package Drawings

7. Design Examples

This section describes the thermal design process using the Power and Thermal Calculator (PTC), with examples for each of the thermal modes in the PTC.

The PTC Thermal tab has three user modes:

  • Find cooling solution for maximum junction temperature limit.
  • Find available thermal margin for cooling solution.
  • Find ambient temperature for specified cooling solution.

Examples for each mode are shown in the following topics.

For each example, you begin with a use case from either a Quartus® Prime output that acts as an input to the PTC, or a new case built in the PTC.

Each example assumes a small module with an Agilex™ 3 device with a heat sink attached, as depicted in the figure below. Additionally, no airflow is assumed over the heat sink. The assumed system includes a 10 layer PCB and the Agilex™ 3 device has a heat sink that measures 50mm x 50mm with 20mm tall fins.

Figure 11. Assumed PCB and Heat Sink
Note: The values in the following examples are for illustrative purposes only; they do not represent any real-world use case.


Section Content
Example 1: Find Cooling Solution for Maximum Junction Temperature Limit
Example 2: Find Available Thermal Margin for Cooling Solution
Example 3: Find the Ambient Temperature for a Specified Cooling Solution

Level Two Title