1G/2.5G/5G/10G Multirate Ethernet PHY Intel® FPGA IP User Guide: Agilex™ 3 and Agilex™ 5 FPGAs and SoCs

Download PDF
ID 813667
Date 4/07/2025
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. About the 1G/2.5G/5G/10G Multirate Ethernet PHY Intel® FPGA IP for Agilex™ 3 and Agilex™ 5 Devices 2. Getting Started 3. Functional Description 4. Parameter Settings for 1G/2.5G/5G/10G Multirate Ethernet PHY Intel® FPGA IP 5. Interface Signals 6. Configuration Registers 7. Debug Checklist 8. 1G/2.5G/5G/10G Multirate Ethernet PHY Intel® FPGA IP User Guide: Agilex™ 3 and Agilex™ 5 FPGAs and SoCs Archives 9. Document Revision History for the 1G/2.5G/5G/10G Multirate Ethernet PHY Intel® FPGA IP User Guide: Agilex™ 3 and Agilex™ 5 FPGAs and SoCs
1. About the 1G/2.5G/5G/10G Multirate Ethernet PHY Intel® FPGA IP for Agilex™ 3 and Agilex™ 5 Devices x
1.1. Release Information 1.2. Features 1.3. Device Family Support 1.4. Device Speed Grade Support 1.5. Resource Utilization
2. Getting Started x
2.1. Introduction to Intel® FPGA IP 2.2. Installing and Licensing Intel® FPGA IPs 2.3. Specifying the IP Core Parameters and Options 2.4. Generated File Structure 2.5. Simulating Intel® FPGA IPs 2.6. Integrating Your IP Core in Your Design
2.2. Installing and Licensing Intel® FPGA IPs x
2.2.1. Intel FPGA IP Evaluation Mode
2.6. Integrating Your IP Core in Your Design x
2.6.1. Adding the GTS System PLL Clocks IP
3. Functional Description x
3.1. Architecture 3.2. Dynamic Reconfiguration Flow 3.3. Clocking and Reset Sequence 3.4. Timing Constraints 3.5. Operation Speed Switching 3.6. USXGMII 3.7. Fmax Requirement
3.1. Architecture x
3.1.1. 2.5G, 1G/2.5G, 1G/2.5G/10G (MGBASE) 3.1.2. 10M/100M/1G/2.5G/5G/10G (USXGMII) 3.1.3. 1G/2.5G/10G MGBASE PCS only
3.2. Dynamic Reconfiguration Flow x
3.2.1. RTL Generation using Dynamic Reconfiguration IP
3.2.1. RTL Generation using Dynamic Reconfiguration IP x
3.2.1.1. Step 1: Generating the 1G/2.5G/5G/10G Multirate Ethernet PHY IP 3.2.1.2. Step 2: QSF settings and Dynamic Reconfiguration (DR) profile assignments 3.2.1.3. Step 3: RTL Generation using Quartus® Prime Pro Edition Tool 3.2.1.4. Step 4: Instantiate the IP top file with the GTS Dynamic Reconfiguration Controller IP
3.3. Clocking and Reset Sequence x
3.3.1. Clocking 3.3.2. Reset Sequence
4. Parameter Settings for 1G/2.5G/5G/10G Multirate Ethernet PHY Intel® FPGA IP x
4.1. Core Configuration 4.2. Analog Parameters
5. Interface Signals x
5.1. Clock Signals 5.2. Reset Signals 5.3. Serial Interface Signals 5.4. Avalon Memory-Mapped Interface Signals 5.5. XGMII Signals 5.6. GMII Signals 5.7. PHY Status Signals 5.8. Transceiver Mode and Operating Speed Signals 5.9. Transceiver Status and Reconfiguration Signals 5.10. GTS Reset Sequencer Signals 5.11. Dynamic Reconfiguration Controller Interface Signals
5.6. GMII Signals x
5.6.1. 1G/2.5G/10G MGBASE PCS Only PMA Interface
6. Configuration Registers x
6.1. Register Map 6.2. PHY Registers
7. Debug Checklist x
7.1. Pre-Debugging Process 7.2. Clock Frequency 7.3. Recommended Reset Handling 7.4. Signals for Signal Tap
1. About the 1G/2.5G/5G/10G Multirate Ethernet PHY Intel® FPGA IP for Agilex™ 3 and Agilex™ 5 Devices
2. Getting Started
3. Functional Description
4. Parameter Settings for 1G/2.5G/5G/10G Multirate Ethernet PHY Intel® FPGA IP
5. Interface Signals
6. Configuration Registers
7. Debug Checklist
8. 1G/2.5G/5G/10G Multirate Ethernet PHY Intel® FPGA IP User Guide: Agilex™ 3 and Agilex™ 5 FPGAs and SoCs Archives
9. Document Revision History for the 1G/2.5G/5G/10G Multirate Ethernet PHY Intel® FPGA IP User Guide: Agilex™ 3 and Agilex™ 5 FPGAs and SoCs

5.11. Dynamic Reconfiguration Controller Interface Signals

Note: The DR Controller interface signals are not available in the 1G/2.5G/5G/10G Multirate Ethernet PHY IP interfaces. They are the new signals added by the GTS dynamic reconfiguration controller IP to the top level RTL module after the dynamic reconfiguration flow.
Table 28.  DR Controller Interface Signals
Signal Name Direction Width Clock Description PHY Configurations
DR-SRC Interface
i_src_ch_pause_request In 1 csr_clk Request pause signal from GTS Dynamic Reconfiguration Controller IP to reset.  
o_src_ch_pause_grant Out 1 csr_clk Indicates that the reset service pause is acknowledged.  
DR Profile Select
one_hot_sel[Profiles-1:0] In 1: 1G/2.5G csr_clk Connects to o_one_hot_sel on the GTS Dynamic Reconfiguration Controller IP.
Note: This signal can be used for mapping to xcvr_mode interface. When one_hot_sel[1:0]= 2'b10, then xcvr_mode[1:0] = 2'b00. All other values would be xcvr_mode[1:0] = 2'b01.
 
DR Controller Avalon® Memory-Mapped Interface
i_dr_lavmm_clk In 1 — 32-bit data Avalon® memory-mapped interface reconfiguration interface with 21-bit address. This Avalon® memory-mapped interface needs to be connected to the GTS Dynamic Reconfiguration Controller IP. Not available for the 1G/2.5G/5G/10G Multirate Ethernet PHY IP but added to the mr_top module after the dynamic reconfiguration flow.
i_dr_lavmm_addr In 21 —
i_dr_lavmm_be In 4 —
i_dr_lavmm_read In 1 —
i_dr_lavmm_wdata In 32 —
i_dr_lavmm_write In 1 —
o_dr_lavmm_rdata Out 32 —
o_dr_lavmm_rdata_valid Out 1 —
o_dr_lavmm_waitreq Out 1 —
i_dr_lavmm_rstn In 1 —
Refer to the Dynamic Reconfiguration Flow for the 1G/2.5G/5G/10G Multirate Ethernet PHY interface signals name change after the dynamic reconfiguration.
Related Information
Level Two Title