Arria V Avalon-ST Interface for PCIe Solutions: User Guide

Download PDF
ID 683660
Date 5/12/2017
Public
Document Table of Contents
Document Table of Contents x
1. Datasheet 2. Getting Started with the Arria V Hard IP for PCI Express 3. Parameter Settings 4. Interfaces and Signal Descriptions 5. Registers 6. Interrupts 7. Error Handling 8. IP Core Architecture 9. Transaction Layer Protocol (TLP) Details 10. Throughput Optimization 11. Design Implementation 12. Additional Features 13. Hard IP Reconfiguration 14. Transceiver PHY IP Reconfiguration 15. Testbench and Design Example 16. Debugging A. Frequently Asked Questions for PCI Express B. Lane Initialization and Reversal C. Document Revision History
1. Datasheet x
1.1. Arria V Avalon-ST Interface for PCIe Datasheet 1.2. Features 1.3. Release Information 1.4. Device Family Support 1.5. Configurations 1.6. Example Designs 1.7. Debug Features 1.8. IP Core Verification 1.9. Performance and Resource Utilization 1.10. Recommended Speed Grades 1.11. Creating a Design for PCI Express
1.8. IP Core Verification x
1.8.1. Compatibility Testing Environment
2. Getting Started with the Arria V Hard IP for PCI Express x
2.1. Qsys Design Flow 2.2. Modifying the Example Design 2.3. Using the IP Catalog To Generate Your Arria V Hard IP for PCI Express as a Separate Component
2.1. Qsys Design Flow x
2.1.1. Generating the Testbench 2.1.2. Simulating the Example Design 2.1.3. Generating Synthesis Files 2.1.4. Understanding the Files Generated 2.1.5. Understanding Physical Placement of the PCIe IP Core 2.1.6. Compiling the Design in the Quartus® Prime Software
3. Parameter Settings x
3.1. Avalon-ST System Settings 3.2. Link Capabilities 3.3. Port Function Parameters Shared Across All Port Functions 3.4. Port Function Parameters Defined Separately for All Port Functions
3.3. Port Function Parameters Shared Across All Port Functions x
3.3.1. Device Capabilities 3.3.2. Error Reporting 3.3.3. Link Capabilities 3.3.4. Slot Capabilities 3.3.5. Power Management
3.4. Port Function Parameters Defined Separately for All Port Functions x
3.4.1. Base Address Register (BAR) and Expansion ROM Settings 3.4.2. Base and Limit Registers for Root Ports 3.4.3. Device Identification Registers for Function <n> 3.4.4. Func <n> Device 3.4.5. Func <n> Link 3.4.6. Func <n> MSI and MSI-X Capabilities 3.4.7. Func <n> Legacy Interrupt
4. Interfaces and Signal Descriptions x
4.1. Clock Signals 4.2. Reset, Status, and Link Training Signals 4.3. ECRC Forwarding 4.4. Error Signals 4.5. Interrupts for Endpoints 4.6. Interrupts for Root Ports 4.7. Completion Side Band Signals 4.8. LMI Signals 4.9. Transaction Layer Configuration Space Signals 4.10. Hard IP Reconfiguration Interface 4.11. Power Management Signals 4.12. Physical Layer Interface Signals
4.9. Transaction Layer Configuration Space Signals x
4.9.1. Configuration Space Register Access Timing 4.9.2. Configuration Space Register Access
4.12. Physical Layer Interface Signals x
4.12.1. Serial Data Signals 4.12.2. PIPE Interface Signals 4.12.3. Test Signals
4.12.1. Serial Data Signals x
4.12.1.1. Physical Layout of Hard IP in Arria V Devices 4.12.1.2. Channel Placement in Arria V Devices
5. Registers x
5.1. Correspondence between Configuration Space Registers and the PCIe Specification 5.2. Type 0 Configuration Space Registers 5.3. Type 1 Configuration Space Registers 5.4. PCI Express Capability Structures 5.5. Intel-Defined VSEC Registers 5.6. Advanced Error Reporting Capability
5.5. Intel-Defined VSEC Registers x
5.5.1. CvP Registers
5.6. Advanced Error Reporting Capability x
5.6.1. Uncorrectable Internal Error Mask Register 5.6.2. Uncorrectable Internal Error Status Register 5.6.3. Correctable Internal Error Mask Register 5.6.4. Correctable Internal Error Status Register
6. Interrupts x
6.1. Interrupts for Endpoints 6.2. Interrupts for Root Ports
6.1. Interrupts for Endpoints x
6.1.1. MSI and Legacy Interrupts 6.1.2. MSI-X 6.1.3. Implementing MSI-X Interrupts 6.1.4. Legacy Interrupts
7. Error Handling x
7.1. Physical Layer Errors 7.2. Data Link Layer Errors 7.3. Transaction Layer Errors 7.4. Error Reporting and Data Poisoning 7.5. Uncorrectable and Correctable Error Status Bits
8. IP Core Architecture x
8.1. Top-Level Interfaces 8.2. Transaction Layer 8.3. Data Link Layer 8.4. Physical Layer 8.5. Multi-Function Support
8.1. Top-Level Interfaces x
8.1.1. Avalon-ST Interface 8.1.2. Clocks and Reset 8.1.3. Local Management Interface (LMI Interface) 8.1.4. Hard IP Reconfiguration 8.1.5. Transceiver Reconfiguration 8.1.6. Interrupts 8.1.7. PIPE
8.2. Transaction Layer x
8.2.1. Configuration Space
9. Transaction Layer Protocol (TLP) Details x
9.1. Supported Message Types 9.2. Transaction Layer Routing Rules 9.3. Receive Buffer Reordering
9.1. Supported Message Types x
9.1.1. INTX Messages 9.1.2. Power Management Messages 9.1.3. Error Signaling Messages 9.1.4. Locked Transaction Message 9.1.5. Slot Power Limit Message 9.1.6. Vendor-Defined Messages 9.1.7. Hot Plug Messages
9.3. Receive Buffer Reordering x
9.3.1. Using Relaxed Ordering
10. Throughput Optimization x
10.1. Throughput of Posted Writes 10.2. Throughput of Non-Posted Reads
11. Design Implementation x
11.1. Making Analog QSF Assignments Using the Assignment Editor 11.2. Making Pin Assignments to Assign I/O Standard to Serial Data Pins 11.3. Recommended Reset Sequence to Avoid Link Training Issues 11.4. SDC Timing Constraints
12. Additional Features x
12.1. Configuration over Protocol (CvP) 12.2. Autonomous Mode 12.3. ECRC
12.2. Autonomous Mode x
12.2.1. Enabling Autonomous Mode 12.2.2. Enabling CvP Initialization
12.3. ECRC x
12.3.1. ECRC on the RX Path 12.3.2. ECRC on the TX Path
14. Transceiver PHY IP Reconfiguration x
14.1. Connecting the Transceiver Reconfiguration Controller IP Core 14.2. Transceiver Reconfiguration Controller Connectivity for Designs Using CvP
15. Testbench and Design Example x
15.1. Endpoint Testbench 15.2. Root Port Testbench 15.3. Test Driver Module 15.4. Root Port Design Example 15.5. Root Port BFM Overview 15.6. BFM Procedures and Functions 15.7. Setting Up Simulation
15.1. Endpoint Testbench x
15.1.1. Endpoint Testbench for SR-IOV
15.5. Root Port BFM Overview x
15.5.1. BFM Memory Map 15.5.2. Configuration Space Bus and Device Numbering 15.5.3. Configuration of Root Port and Endpoint 15.5.4. Issuing Read and Write Transactions to the Application Layer
15.6. BFM Procedures and Functions x
15.6.1. ebfm_barwr Procedure 15.6.2. ebfm_barwr_imm Procedure 15.6.3. ebfm_barrd_wait Procedure 15.6.4. ebfm_barrd_nowt Procedure 15.6.5. ebfm_cfgwr_imm_wait Procedure 15.6.6. ebfm_cfgwr_imm_nowt Procedure 15.6.7. ebfm_cfgrd_wait Procedure 15.6.8. ebfm_cfgrd_nowt Procedure 15.6.9. BFM Configuration Procedures 15.6.10. BFM Shared Memory Access Procedures 15.6.11. BFM Log and Message Procedures 15.6.12. Verilog HDL Formatting Functions
15.6.9. BFM Configuration Procedures x
15.6.9.1. ebfm_cfg_rp_ep Procedure 15.6.9.2. ebfm_cfg_decode_bar Procedure
15.6.10. BFM Shared Memory Access Procedures x
15.6.10.1. Shared Memory Constants 15.6.10.2. shmem_write Task 15.6.10.3. shmem_read Function 15.6.10.4. shmem_display Verilog HDL Function 15.6.10.5. shmem_fill Procedure 15.6.10.6. shmem_chk_ok Function
15.6.11. BFM Log and Message Procedures x
15.6.11.1. ebfm_display Verilog HDL Function 15.6.11.2. ebfm_log_stop_sim Verilog HDL Function 15.6.11.3. ebfm_log_set_suppressed_msg_mask Task 15.6.11.4. ebfm_log_set_stop_on_msg_mask Verilog HDL Task 15.6.11.5. ebfm_log_open Verilog HDL Function 15.6.11.6. ebfm_log_close Verilog HDL Function
15.6.12. Verilog HDL Formatting Functions x
15.6.12.1. himage1 15.6.12.2. himage2 15.6.12.3. himage4 15.6.12.4. himage8 15.6.12.5. himage16 15.6.12.6. dimage1 15.6.12.7. dimage2 15.6.12.8. dimage3 15.6.12.9. dimage4 15.6.12.10. dimage5 15.6.12.11. dimage6 15.6.12.12. dimage7
15.7. Setting Up Simulation x
15.7.1. Changing Between Serial and PIPE Simulation 15.7.2. Using the PIPE Interface for Gen1 and Gen2 Variants 15.7.3. Viewing the Important PIPE Interface Signals 15.7.4. Disabling the Scrambler for Gen1 and Gen2 Simulations 15.7.5. Disabling 8B/10B Encoding and Decoding for Gen1 and Gen2 Simulations 15.7.6. Changing between the Hard and Soft Reset Controller
16. Debugging x
16.1. Hardware Bring-Up Issues 16.2. Link Training 16.3. Use Third-Party PCIe Analyzer 16.4. BIOS Enumeration Issues
16.2. Link Training x
16.2.1. Link Hangs in L0 State
C. Document Revision History x
C.1. Document Revision History of the Arria V Avalon® Streaming (Avalon-ST) Interface for PCIe* Solutions User Guide
1. Datasheet
2. Getting Started with the Arria V Hard IP for PCI Express
3. Parameter Settings
4. Interfaces and Signal Descriptions
5. Registers
6. Interrupts
7. Error Handling
8. IP Core Architecture
9. Transaction Layer Protocol (TLP) Details
10. Throughput Optimization
11. Design Implementation
12. Additional Features
13. Hard IP Reconfiguration
14. Transceiver PHY IP Reconfiguration
15. Testbench and Design Example
16. Debugging
A. Frequently Asked Questions for PCI Express
B. Lane Initialization and Reversal
C. Document Revision History

5.5.1. CvP Registers

Table 48.  CvP Status The CvP Status register allows software to monitor the CvP status signals.
Bits Register Description Reset Value Access
[31:26] Reserved 0x00 RO
[25] PLD_CORE_READY. From FPGA fabric. This status bit is provided for debug. Variable RO
[24] PLD_CLK_IN_USE. From clock switch module to fabric. This status bit is provided for debug. Variable RO
[23] CVP_CONFIG_DONE. Indicates that the FPGA control block has completed the device configuration via CvP and there were no errors. Variable RO
[22] Reserved Variable RO
[21] USERMODE. Indicates if the configurable FPGA fabric is in user mode. Variable RO
[20] CVP_EN. Indicates if the FPGA control block has enabled CvP mode. Variable RO
[19] CVP_CONFIG_ERROR. Reflects the value of this signal from the FPGA control block, checked by software to determine if there was an error during configuration. Variable RO
[18] CVP_CONFIG_READY. Reflects the value of this signal from the FPGA control block, checked by software during programming algorithm. Variable RO
[17:0] Reserved Variable RO
Table 49.  CvP Mode Control The CvP Mode Control register provides global control of the CvP operation.

Bits

Register Description

Reset Value

Access

[31:16]

Reserved.

0x0000

RO

[15:8]

CVP_NUMCLKS.

This is the number of clocks to send for every CvP data write. Set this field to one of the values below depending on your configuration image:

  • 0x01 for uncompressed and unencrypted images
  • 0x04 for uncompressed and encrypted images
  • 0x08 for all compressed images

0x00

RW

[7:3]

Reserved.

0x0

RO

[2]

CVP_FULLCONFIG. Request that the FPGA control block reconfigure the entire FPGA including the Arria V Hard IP for PCI Express, bring the PCIe link down.

1’b0

RW

[1]

HIP_CLK_SEL. Selects between PMA and fabric clock when USER_MODE = 1 and PLD_CORE_READY = 1. The following encodings are defined:

  • 1: Selects internal clock from PMA which is required for CVP_MODE.
  • 0: Selects the clock from soft logic fabric. This setting should only be used when the fabric is configured in USER_MODE with a configuration file that connects the correct clock.

To ensure that there is no clock switching during CvP, you should only change this value when the Hard IP for PCI Express has been idle for 10 µs and wait 10 µs after changing this value before resuming activity.

1’b0

RW

[0]

CVP_MODE. Controls whether the IP core is in CVP_MODE or normal mode. The following encodings are defined:

  • 1:CVP_MODE is active. Signals to the FPGA control block active and all TLPs are routed to the Configuration Space. This CVP_MODE cannot be enabled if CVP_EN = 0.
  • 0: The IP core is in normal mode and TLPs are routed to the FPGA fabric.

1’b0

RW

Table 50.  CvP Data Registers

The following table defines the CvP Data registers. For 64-bit data, the optional CvP Data2 stores the upper 32 bits of data. Programming software should write the configuration data to these registers. If you Every write to these register sets the data output to the FPGA control block and generates <n> clock cycles to the FPGA control block as specified by the CVP_NUM_CLKS field in the CvP Mode Control register. Software must ensure that all bytes in the memory write dword are enabled. You can access this register using configuration writes, alternatively, when in CvP mode, these registers can also be written by a memory write to any address defined by a memory space BAR for this device. Using memory writes should allow for higher throughput than configuration writes.

Bits

Register Description

Reset Value

Access

[31:0]

Upper 32 bits of configuration data to be transferred to the FPGA control block to configure the device. You can choose 32- or 64-bit data.

0x00000000

RW

[31:0]

Lower 32 bits of configuration data to be transferred to the FPGA control block to configure the device.

0x00000000

RW

Table 51.  CvP Programming Control Register This register is written by the programming software to control CvP programming.

Bits

Register Description

Reset Value

Access

[31:2]

Reserved.

0x0000

RO

[1]

START_XFER. Sets the CvP output to the FPGA control block indicating the start of a transfer.

1’b0

RW

[0]

CVP_CONFIG. When asserted, instructs that the FPGA control block begin a transfer via CvP.

1’b0

RW

Level Two Title