Cyclone® 10 LP FPGA Evaluation Kit User Guide

Download PDF
ID 683580
Date 11/18/2025
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Getting Started 3. Evaluation Board Setup 4. Evaluation Board Components 5. Simple Socket Server 6. Board Test System 7. Document Revision History for the Cyclone® 10 LP FPGA Evaluation Kit User Guide A. Safety and Regulatory Compliance Information
1. Overview x
1.1. Feature Summary 1.2. Box Contents 1.3. Evaluation Board Revisions 1.4. Recommended Operating Conditions
1.2. Box Contents x
1.2.1. Power Supply Description
2. Getting Started x
2.1. Before You Begin 2.2. Handling the Board 2.3. Software and Driver Installation
2.2. Handling the Board x
2.2.1. Handling the DIP Switches
2.3. Software and Driver Installation x
2.3.1. Installing the Quartus® Prime Standard Edition Software 2.3.2. Installing the Evaluation Kit 2.3.3. Installing the Intel® FPGA Download Cable II Driver
3. Evaluation Board Setup x
3.1. Powering Up the Evaluation Board 3.2. Default Switch Settings 3.3. Recovering Factory Default Settings
4. Evaluation Board Components x
4.1. Board Overview 4.2. Cyclone® 10 LP FPGA Overview 4.3. MAX® 10 System Controller Overview 4.4. FPGA Configuration 4.5. Status Elements 4.6. Setup Elements 4.7. General User Input/Output 4.8. Clocks 4.9. Connectors and Interfaces 4.10. Memory 4.11. System Power
4.4. FPGA Configuration x
4.4.1. Using the Quartus® Prime Programmer 4.4.2. Program Onboard EPCQ or EPCQ-A Flash Memory 4.4.3. Active Serial Configuration
4.9. Connectors and Interfaces x
4.9.1. Gigabit Ethernet PHY 4.9.2. 2x20 GPIO Expansion Header 4.9.3. Arduino Connectors 4.9.4. Pmod Connectors
4.9.3. Arduino Connectors x
4.9.3.1. Digital I/Os 4.9.3.2. Analog Inputs 4.9.3.3. Arduino Power
4.10. Memory x
4.10.1. HyperRAM 4.10.2. EPCQ or EPCQ-A Flash Memory
4.11. System Power x
4.11.1. Power Supply Options 4.11.2. Power Tree 4.11.3. Current Measurement
5. Simple Socket Server x
5.1. Connecting to the Simple Socket Server
6. Board Test System x
6.1. The Configure Menu 6.2. The Sys Info Tab 6.3. The GPIO Tab 6.4. The FLASH Tab 6.5. The HRAM Tab 6.6. The Power Monitor 6.7. The Clock Controller
A. Safety and Regulatory Compliance Information x
A.1. Safety and Regulatory Information A.2. Compliance Information
A.1. Safety and Regulatory Information x
A.1.1. Safety Warnings A.1.2. Safety Cautions
1. Overview
2. Getting Started
3. Evaluation Board Setup
4. Evaluation Board Components
5. Simple Socket Server
6. Board Test System
7. Document Revision History for the Cyclone® 10 LP FPGA Evaluation Kit User Guide
A. Safety and Regulatory Compliance Information

5. Simple Socket Server

The Cyclone® 10 LP FPGA Evaluation Board ships with the Simple Socket Server design example stored in the factory portion of the flash memory. The design consists of a Nios® II embedded processor and an Ethernet MAC.
Note: The Cyclone® 10 LP Evaluation Board Rev A1 hardware design does not include Ethernet MAC support. If you have a Rev A1 board, download and install the Rev A2 design. Refer to the Installing the Evaluation Kit section for instructions to download the Rev A2 design.

When you power up the board, the Cyclone® 10 LP FPGA configures with the Simple Socket Server design example. The design can obtain an IP address from any DHCP server and serve a telnet server to any host computer on the same network. The telnet server allows you to control the LEDs on the board.

The source code for the Simple Socket Server design resides in the <package dir>\examples\golden_system_ref_design directory. If the Simple Socket Server is corrupted or deleted from the flash memory, you might need to restore the board's original contents, using the BTS application.


Section Content
Connecting to the Simple Socket Server

Related Information
Level Two Title