Cyclone® 10 LP FPGA Evaluation Kit User Guide

Download PDF
ID 683580
Date 11/18/2025
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Getting Started 3. Evaluation Board Setup 4. Evaluation Board Components 5. Simple Socket Server 6. Board Test System 7. Document Revision History for the Cyclone® 10 LP FPGA Evaluation Kit User Guide A. Safety and Regulatory Compliance Information
1. Overview x
1.1. Feature Summary 1.2. Box Contents 1.3. Evaluation Board Revisions 1.4. Recommended Operating Conditions
1.2. Box Contents x
1.2.1. Power Supply Description
2. Getting Started x
2.1. Before You Begin 2.2. Handling the Board 2.3. Software and Driver Installation
2.2. Handling the Board x
2.2.1. Handling the DIP Switches
2.3. Software and Driver Installation x
2.3.1. Installing the Quartus® Prime Standard Edition Software 2.3.2. Installing the Evaluation Kit 2.3.3. Installing the Intel® FPGA Download Cable II Driver
3. Evaluation Board Setup x
3.1. Powering Up the Evaluation Board 3.2. Default Switch Settings 3.3. Recovering Factory Default Settings
4. Evaluation Board Components x
4.1. Board Overview 4.2. Cyclone® 10 LP FPGA Overview 4.3. MAX® 10 System Controller Overview 4.4. FPGA Configuration 4.5. Status Elements 4.6. Setup Elements 4.7. General User Input/Output 4.8. Clocks 4.9. Connectors and Interfaces 4.10. Memory 4.11. System Power
4.4. FPGA Configuration x
4.4.1. Using the Quartus® Prime Programmer 4.4.2. Program Onboard EPCQ or EPCQ-A Flash Memory 4.4.3. Active Serial Configuration
4.9. Connectors and Interfaces x
4.9.1. Gigabit Ethernet PHY 4.9.2. 2x20 GPIO Expansion Header 4.9.3. Arduino Connectors 4.9.4. Pmod Connectors
4.9.3. Arduino Connectors x
4.9.3.1. Digital I/Os 4.9.3.2. Analog Inputs 4.9.3.3. Arduino Power
4.10. Memory x
4.10.1. HyperRAM 4.10.2. EPCQ or EPCQ-A Flash Memory
4.11. System Power x
4.11.1. Power Supply Options 4.11.2. Power Tree 4.11.3. Current Measurement
5. Simple Socket Server x
5.1. Connecting to the Simple Socket Server
6. Board Test System x
6.1. The Configure Menu 6.2. The Sys Info Tab 6.3. The GPIO Tab 6.4. The FLASH Tab 6.5. The HRAM Tab 6.6. The Power Monitor 6.7. The Clock Controller
A. Safety and Regulatory Compliance Information x
A.1. Safety and Regulatory Information A.2. Compliance Information
A.1. Safety and Regulatory Information x
A.1.1. Safety Warnings A.1.2. Safety Cautions
1. Overview
2. Getting Started
3. Evaluation Board Setup
4. Evaluation Board Components
5. Simple Socket Server
6. Board Test System
7. Document Revision History for the Cyclone® 10 LP FPGA Evaluation Kit User Guide
A. Safety and Regulatory Compliance Information

4.6. Setup Elements

Table 9.  DIP Switches
Board Reference Schematic Signal Name Description
SW1.4 VTAP_BYPASSn Pull low to disable Virtual JTAG TAP in device chain
Table 10.  Push Buttons
Board Reference Schematic Signal Name Description
S1 C10_nCONFIG Press this push button to reconfigure Cyclone® 10 LP FPGA device
S2 C10_RESETn Press this push button to perform a device-wide reset, connect to Cyclone® 10 LP FPGA DEV_CLRn
Level Two Title