Intel® Arria® 10 FPGA Development Kit User Guide

Download PDF
ID 683526
Date 1/13/2024
Public
Document Table of Contents
Document Table of Contents x
1. Intel® Arria® 10 FPGA Development Kit Overview 2. Getting Started 3. Development Board Setup 4. Board Test System 5. Board Update Portal 6. Board Components A. Additional Information
1. Intel® Arria® 10 FPGA Development Kit Overview x
1.1. General Description 1.2. Recommended Operating Conditions 1.3. Handling the Board
2. Getting Started x
2.1. Installing the Subscription Edition Software 2.2. Development Kit Package 2.3. Installing the USB-Blaster Driver
2.1. Installing the Subscription Edition Software x
2.1.1. Activating Your License
3. Development Board Setup x
3.1. Applying Power to the Board 3.2. Default Switch and Jumper Settings 3.3. Default Switch and Resistor Settings 3.4. Factory Reset
4. Board Test System x
4.1. Preparing the Board 4.2. Running the Board Test System 4.3. Version Selector 4.4. Using the Board Test System
4.4. Using the Board Test System x
4.4.1. Using the Configure Menu 4.4.2. The System Info Tab 4.4.3. The GPIO Tab 4.4.4. The Flash Tab 4.4.5. The XCVR Tab 4.4.6. The PCIe Tab 4.4.7. The FMC A Tab 4.4.8. The FMC B Tab 4.4.9. The DDR3 Tab 4.4.10. The DDR4 Tab 4.4.11. The Power Monitor 4.4.12. The Clock Control
5. Board Update Portal x
5.1. Connecting to the Board Update Portal Web Page
5.1. Connecting to the Board Update Portal Web Page x
5.1.1. Using the Board Update Portal to Update User Designs
6. Board Components x
6.1. Board Overview 6.2. MAX V CPLD System Controller 6.3. FPGA Configuration 6.4. Status Elements 6.5. User Input/Output 6.6. Clock Circuitry 6.7. Components and Interfaces 6.8. Memory 6.9. Board Power Supply 6.10. Daughtercards
6.3. FPGA Configuration x
6.3.1. Configuring the FPGA Using Programmer
6.5. User Input/Output x
6.5.1. User-Defined Push Buttons 6.5.2. User-Defined DIP Switch 6.5.3. User-Defined LEDs 6.5.4. Character LCD 6.5.5. DisplayPort 6.5.6. SDI Video Input/Output Ports
6.6. Clock Circuitry x
6.6.1. On-Board Oscillators 6.6.2. Off-Board Clock I/O
6.7. Components and Interfaces x
6.7.1. PCI Express 6.7.2. 10/100/1000 Ethernet PHY 6.7.3. HiLo External Memory Interface 6.7.4. FMC 6.7.5. QSFP 6.7.6. SFP+ 6.7.7. I2C
6.8. Memory x
6.8.1. Flash 6.8.2. Programming the Flash Using Intel® Quartus® Prime Programmer
6.9. Board Power Supply x
6.9.1. Power Distribution System 6.9.2. Power Measurement
6.10. Daughtercards x
6.10.1. External Memory Interface
6.10.1. External Memory Interface x
6.10.1.1. DDR3L 6.10.1.2. DDR4 6.10.1.3. RLDRAM 3 6.10.1.4. QDR-IV 6.10.1.5. FMC Loopback Card
6.10.1.5. FMC Loopback Card x
6.10.1.5.1. High Pin Count (HBC) 6.10.1.5.2. Low Pin Count (LPC)
A. Additional Information x
A.1. Document Revision History for the Intel® Arria® 10 FPGA Development Kit User Guide A.2. Compliance and Conformity Statements
A.2. Compliance and Conformity Statements x
A.2.1. CE EMI Conformity Caution
1. Intel® Arria® 10 FPGA Development Kit Overview
2. Getting Started
3. Development Board Setup
4. Board Test System
5. Board Update Portal
6. Board Components
A. Additional Information

6.8.2. Programming the Flash Using Quartus Programmer

You can use the Quartus Programmer to program the flash with your Programmer Object File (.pof).

Ensure the following conditions are met before you proceed:
  • The Quartus Programmer and the USB-Blaster II driver are installed on the host computer.
  • The micro-USB cable is connected to the FPGA development board.
  • Power to the board is on, and no other applications that use the JTAG chain are running.
  • The design running in the FPGA does not drive the FM bus.
Execute the steps below to program the Flash
  1. Start the Quartus Programmer.
  2. Click Auto Detect to display the devices in the JTAG chain.
  3. Select the flash attached to the MAX V and then click Change File and select the path to the desired .pof. If the flash is not detected, configure the FPGA with <package root directory>\examples\board_test_system\image\<Silicon Type>\dummy.sof and then go to step 2, refer to Configuring the FPGA Using Programmer.
  4. Turn on the Program/Configure option for the added file.

  5. Click Start to program the selected file to the flash. Programming is complete when the progress bar reaches 100%.

Attention: Using the Quartus Programmer to program a device on the board causes other JTAG-based applications such as the Board Test System and the Power Monitor to lose their connection to the board. Restart those applications after programming is complete.
Level Two Title