GTS Transceiver PHY User Guide: Agilex™ 3 FPGAs and SoCs

Download PDF
ID 848344
Date 4/07/2025
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. GTS Transceiver Overview 2. GTS Transceiver Architecture 3. Implementing the GTS PMA/FEC Direct PHY Intel FPGA IP 4. Implementing the GTS System PLL Clocks Intel FPGA IP 5. Implementing the GTS Reset Sequencer Intel FPGA IP 6. GTS PMA/FEC Direct PHY Intel FPGA IP Example Design 7. Design Assistance Tools 8. Debugging GTS Transceiver Links with Transceiver Toolkit 9. Document Revision History for the GTS Transceiver PHY User Guide: Agilex™ 3 FPGAs and SoCs
1. GTS Transceiver Overview x
1.1. GTS Transceiver Design Flow
2. GTS Transceiver Architecture x
2.1. Building Blocks 2.2. Channel Placement Rules and Design Requirements 2.3. PMA Architecture 2.4. PCS Architecture 2.5. Forward Error Correction (FEC) Architecture 2.6. Clock Architecture 2.7. Bonding and Deskew
2.1. Building Blocks x
2.1.1. PMA 2.1.2. FEC 2.1.3. PCS 2.1.4. Ethernet MAC 2.1.5. PCI Express* Hard IP 2.1.6. PLL and Clock Networks 2.1.7. Avalon® Memory-Mapped Interface
2.1.1. PMA x
2.1.1.1. Protocol Support Using PMA Direct Mode
2.1.1.1. Protocol Support Using PMA Direct Mode x
2.1.1.1.1. SDI 2.1.1.1.2. HDMI
2.2. Channel Placement Rules and Design Requirements x
2.2.1. Hard IP Rules 2.2.2. Use Scenario Rules 2.2.3. Unused PMA Rules 2.2.4. General Design Requirement
2.2.3. Unused PMA Rules x
2.2.3.1. Unused PMA Not Planned for Use in the Future 2.2.3.2. Unused PMA Planned for Use in the Future
2.3. PMA Architecture x
2.3.1. Transmitter PMA Architecture 2.3.2. Receiver PMA Architecture 2.3.3. PMA Loopback Modes
2.3.1. Transmitter PMA Architecture x
2.3.1.1. Transmitter Buffer 2.3.1.2. Serializer 2.3.1.3. Data Pattern Generator and Verifier
2.3.2. Receiver PMA Architecture x
2.3.2.1. Receiver Buffer and Equalizer 2.3.2.2. Deserializer 2.3.2.3. CDR Block 2.3.2.4. PMA Tuning
2.3.2.1. Receiver Buffer and Equalizer x
2.3.2.1.1. Control Unit
2.5. Forward Error Correction (FEC) Architecture x
2.5.1. FEC Loopback Mode
2.6. Clock Architecture x
2.6.1. Reference Clock Network 2.6.2. Datapath Clock Network 2.6.3. System PLL 2.6.4. Datapath Clock Cadences 2.6.5. Shared Clocking Resources Between the GTS Transceiver Bank and HVIO Bank
2.6.1. Reference Clock Network x
2.6.1.1. PMA Primary PLL Configuration
2.6.3. System PLL x
2.6.3.1. I/O PLLs in HVIO Bank as System PLL 2.6.3.2. System PLL Clock for FPGA Core 2.6.3.3. System PLL with HVIO Reference Clock
2.7. Bonding and Deskew x
2.7.1. Bonding Architecture 2.7.2. TX Deskew Function
3. Implementing the GTS PMA/FEC Direct PHY Intel FPGA IP x
3.1. IP Overview 3.2. Designing with the GTS PMA/FEC Direct PHY Intel FPGA IP 3.3. Configuring the GTS PMA/FEC Direct PHY Intel FPGA IP 3.4. Signal and Port Reference 3.5. Bit Mapping for PMA, FEC, and PCS Mode PHY TX and RX Datapath 3.6. Clocking 3.7. Custom Cadence Generation Ports and Logic 3.8. Asserting Reset 3.9. Bonding Implementation 3.10. Configuration Register 3.11. Configuring the GTS PMA/FEC Direct PHY Intel FPGA IP for Hardware Testing 3.12. Configurable Quartus® Prime Software Settings 3.13. Hardware Configuration Using the Avalon® Memory-Mapped Interface
3.1. IP Overview x
3.1.1. PMA Direct Supported Modes 3.1.2. FEC Direct Supported Modes 3.1.3. PCS Direct Supported Modes 3.1.4. Unsupported PMA/FEC/PCS Modes
3.3. Configuring the GTS PMA/FEC Direct PHY Intel FPGA IP x
3.3.1. Preset IP Parameter Settings 3.3.2. Mode and Common Datapath Options 3.3.3. TX Datapath Options 3.3.4. RX Datapath Options 3.3.5. PMA Configuration Rules for Specific Protocol Mode Implementations 3.3.6. FEC Options 3.3.7. PCS Options 3.3.8. Avalon® Memory-Mapped Interface Options 3.3.9. Register Map IP-XACT Support 3.3.10. Analog Parameter Options
3.3.3. TX Datapath Options x
3.3.3.1. TX PMA Interface Parameters
3.3.4. RX Datapath Options x
3.3.4.1. RX PMA Interface Parameters
3.3.5. PMA Configuration Rules for Specific Protocol Mode Implementations x
3.3.5.1. PMA Configuration Rules for SDI Mode 3.3.5.2. PMA Configuration Rules for HDMI Mode
3.4. Signal and Port Reference x
3.4.1. TX and RX Parallel and Serial Interface Signals 3.4.2. TX and RX Reference Clock and Clock Output Interface Signals 3.4.3. Reset Signals 3.4.4. FEC Signals 3.4.5. Custom Cadence Control and Status Signals 3.4.6. RX PMA Status Signals 3.4.7. TX and RX PMA and Core Interface FIFO Signals 3.4.8. Avalon Memory-Mapped Interface Signals
3.6. Clocking x
3.6.1. Clock Ports 3.6.2. Recommended tx/rx_coreclkin Connection and tx/rx_clkout2 Source 3.6.3. Port Widths and Recommended Connections for tx/rx_coreclkin, tx/rx_clkout, and tx/rx_clkout2 3.6.4. PMA Fractional Mode 3.6.5. Input Reference Clock Buffer Protection
3.6.5. Input Reference Clock Buffer Protection x
3.6.5.1. Reference Clock Buffer Register Information 3.6.5.2. Re-enabling the Reference Clock Buffers
3.7. Custom Cadence Generation Ports and Logic x
3.7.1. Enabling the i_tx_cadence_slow_clk_locked Port
3.8. Asserting Reset x
3.8.1. Reset Signal Requirements 3.8.2. Power On Reset Requirements 3.8.3. Reset Signals—Block Level 3.8.4. Run-time Reset Sequence—TX 3.8.5. Run-time Reset Sequence—RX 3.8.6. Run-time Reset Sequence—TX + RX 3.8.7. RX Data Loss/CDR Lock Loss (Auto-Recovery) 3.8.8. TX PLL Lock Loss 3.8.9. TX PLL Lock Loss Auto-Recovery (Soft CSR Enabled)
3.9. Bonding Implementation x
3.9.1. Bonding Placement Requirements 3.9.2. Multilane RX Simplex Implementation
3.10. Configuration Register x
3.10.1. GTS PMA and FEC Direct PHY Soft CSR Register Map 3.10.2. GTS PMA Register Map 3.10.3. Accessing Configuration Registers
3.10.2. GTS PMA Register Map x
3.10.2.1. Logical Avalon® Memory-Mapped Port Indexing
3.10.3. Accessing Configuration Registers x
3.10.3.1. Accessing GTS PMA and FEC Direct PHY Soft CSR Registers 3.10.3.2. Accessing GTS PMA Registers
3.11. Configuring the GTS PMA/FEC Direct PHY Intel FPGA IP for Hardware Testing x
3.11.1. Using Debug Endpoint Interface within the GTS PMA/FEC Direct PHY Intel FPGA IP 3.11.2. Using JTAG to Avalon Master Bridge Intel FPGA IP
3.11.1. Using Debug Endpoint Interface within the GTS PMA/FEC Direct PHY Intel FPGA IP x
3.11.1.1. RTL Connection Example for Debug Endpoint Avalon® Interface
3.11.2. Using JTAG to Avalon Master Bridge Intel FPGA IP x
3.11.2.1. RTL Connection Example for JTAG to Avalon Master Bridge Intel® FPGA IP
3.13. Hardware Configuration Using the Avalon® Memory-Mapped Interface x
3.13.1. Direct Register Method 3.13.2. GTS Attribute Access Method
3.13.1. Direct Register Method x
3.13.1.1. Direct Register Method Examples
3.13.2. GTS Attribute Access Method x
3.13.2.1. GTS Attribute Access Method Example 1 3.13.2.2. GTS Attribute Access Method Example 2 3.13.2.3. GTS Attribute Access Method Example 3
4. Implementing the GTS System PLL Clocks Intel FPGA IP x
4.1. IP Parameters 4.2. IP Port List 4.3. Mode of System PLL - System PLL Reference Clock and Output Frequencies 4.4. Guidelines for GTS System PLL Clocks Intel FPGA IP Usage 4.5. Guidelines to Indicate System PLL Reference Clock is Ready
4.5. Guidelines to Indicate System PLL Reference Clock is Ready x
4.5.1. Example Flow to Indicate System PLL Reference Clock is Ready
5. Implementing the GTS Reset Sequencer Intel FPGA IP x
5.1. IP Requirements 5.2. IP Parameters 5.3. IP Port List 5.4. GTS Reset Sequencer Intel FPGA IP General Interface 5.5. GTS Reset Sequencer Intel FPGA IP Design Flow 5.6. GTS Reset Sequencer Intel FPGA IP Use Cases 5.7. Connecting the Reference Clock Buffer Status to the GTS Reset Sequencer Intel® FPGA IP
5.6. GTS Reset Sequencer Intel FPGA IP Use Cases x
5.6.1. Example Use Case 1 5.6.2. Example Use Case 2
6. GTS PMA/FEC Direct PHY Intel FPGA IP Example Design x
6.1. Instantiating the GTS PMA/FEC Direct PHY Intel FPGA IP 6.2. Generating the GTS PMA/FEC Direct PHY Intel FPGA IP Example Design 6.3. GTS PMA/FEC Direct PHY Intel FPGA IP Example Design Functional Description 6.4. Simulating the GTS PMA/FEC Direct PHY Intel FPGA IP Example Design Testbench 6.5. Compiling the GTS PMA/FEC Direct PHY Intel FPGA IP Example Design
6.2. Generating the GTS PMA/FEC Direct PHY Intel FPGA IP Example Design x
6.2.1. Fast Simulation Support 6.2.2. GTS PMA/FEC Direct PHY Intel FPGA IP Example Design Directory Structure
6.4. Simulating the GTS PMA/FEC Direct PHY Intel FPGA IP Example Design Testbench x
6.4.1. Modifying the Example Design and Performing Simulation
7. Design Assistance Tools x
7.1. Clocking and Datapath Tool 7.2. TX Equalizer Tool
8. Debugging GTS Transceiver Links with Transceiver Toolkit x
8.1. GTS Transceiver Toolkit Parameter Settings 8.2. GTS Transceiver Toolkit GUI 8.3. GTS Transceiver Debugging Flow Walkthrough
8.2. GTS Transceiver Toolkit GUI x
8.2.1. Collection View
8.3. GTS Transceiver Debugging Flow Walkthrough x
8.3.1. Modifying the Design to Enable GTS Transceiver Debug Toolkit 8.3.2. Programming the Design into an Intel FPGA 8.3.3. Loading the Design to the Transceiver Toolkit 8.3.4. Creating Transceiver Links 8.3.5. Running BER Tests 8.3.6. Running Eye Viewer Tests 8.3.7. Running Link Optimization Tests
1. GTS Transceiver Overview
2. GTS Transceiver Architecture
3. Implementing the GTS PMA/FEC Direct PHY Intel FPGA IP
4. Implementing the GTS System PLL Clocks Intel FPGA IP
5. Implementing the GTS Reset Sequencer Intel FPGA IP
6. GTS PMA/FEC Direct PHY Intel FPGA IP Example Design
7. Design Assistance Tools
8. Debugging GTS Transceiver Links with Transceiver Toolkit
9. Document Revision History for the GTS Transceiver PHY User Guide: Agilex™ 3 FPGAs and SoCs

5.1. IP Requirements

The GTS Reset Sequencer Intel FPGA IP must be instantiated for device that uses transceivers. Refer to the Transceiver Architecture chapter for more information.

The following table shows the logic usage in the FPGA fabric of the GTS Reset Sequencer Intel FPGA IP.
Table 76.  Logic Usage of the GTS Reset Sequencer Intel® FPGA IP (For Agilex® 3 C-Series Devices)
Device Family ALM30 ALUT Logic Register M20K
Agilex® 3 C-Series 52 79 73 0
30 Logic utilization is lower for fewer channel applications.
Level Two Title