Device Migration Guidelines: Agilex™ 5 FPGAs and SoCs D-Series

Download PDF
ID 839365
Date 6/06/2025
Public

Visible to Intel only — GUID: pmf1717575744043

Ixiasoft

View Details

Document Table of Contents
Document Table of Contents x
1. Introduction 2. Migration Scope 3. Functional Area 4. Quartus® Prime Software Design Migration 5. Document Revision History for Device Migration Guidelines: Agilex™ 5 FPGAs and SoCs D-Series
2. Migration Scope x
2.1. Migration Supported Packages 2.2. Migration Scenarios 2.3. Considerations for Migration Planning
2.2. Migration Scenarios x
2.2.1. Vertical Migration 2.2.2. Conditional Migration
2.3. Considerations for Migration Planning x
2.3.1. Package B23D 2.3.2. Package B32B
3. Functional Area x
3.1. I/O 3.2. LVDS SERDES 3.3. Configuration 3.4. External Memory Interface 3.5. MIPI D-PHY 3.6. HPS 3.7. Transceiver 3.8. Power 3.9. Sensor
3.1. I/O x
3.1.1. HSIO 3.1.2. HVIO
3.4. External Memory Interface x
3.4.1. External Memory Protocol Supported in Agilex™ 5 D-Series Devices 3.4.2. External Memory Interface Support 3.4.3. External Memory Interface Migration Consideration
3.4.2. External Memory Interface Support x
3.4.2.1. DDR4 Interfaces 3.4.2.2. DDR5 Interfaces 3.4.2.3. LPDDR4 Interfaces 3.4.2.4. LPDDR5 Interfaces
3.7. Transceiver x
3.7.1. Migration Overview for Transceiver Application 3.7.2. GTS Transceiver Bank Name Change between Device Variant 3.7.3. GTS Transceiver Resources Count 3.7.4. Preserving Unused PMA Lanes
3.7.3. GTS Transceiver Resources Count x
3.7.3.1. Transceiver Resources and Lane Count 3.7.3.2. USB3.1 Hard IP 3.7.3.3. HVIO REFCLK Pin 3.7.3.4. CVP Requirement 3.7.3.5. GTS Transmitter (TX) and GTS Receiver (RX) pin, Reference Clock Pin, and RCOMP Pins 3.7.3.6. System PLL in Downbonded Quads 3.7.3.7. PERST Pin
3.7.3.5. GTS Transmitter (TX) and GTS Receiver (RX) pin, Reference Clock Pin, and RCOMP Pins x
3.7.3.5.1. GTS TX and GTS RX pin, and Reference Clock Pin 3.7.3.5.2. RCOMP_GTS Pins
3.8. Power x
3.8.1. Power Rails for Migration 3.8.2. Voltage Regulator Considerations for Agilex™ 5 Migration
3.9. Sensor x
3.9.1. Temperature Sensor Location Support
4. Quartus® Prime Software Design Migration x
4.1. Migration via Migration GUI for Agilex™ 5 D-Series Devices
1. Introduction
2. Migration Scope
3. Functional Area
4. Quartus® Prime Software Design Migration
5. Document Revision History for Device Migration Guidelines: Agilex™ 5 FPGAs and SoCs D-Series

3.7.3.4. CVP Requirement

If you are migrating between device variants and plan to enable the CVP feature using PCIe Hard IP, always ensure that you enable and power up at least one transceiver bank on the left side of the device where the SDM block is located. You must not connect the power rails of this transceiver bank to GND if you are planning to use the CVP function/feature.

Level Two Title