F-Tile PMA and FEC Direct PHY Multirate Intel® FPGA IP User Guide

ID 720998
Date 4/01/2024
Public
Document Table of Contents

3. Parameters

You can select the F-Tile PMA/FEC Direct PHY Multirate Intel FPGA IP core for Agilex™ 7 devices from the Quartus® Prime Pro Edition software IP catalog. To customize the IP core, specify the parameters in the IP parameter editor.
The following figures and tables list and describe all the IP parameters and how they appear in the GUI.
Figure 1. IP Parameter Editor: General Tab
Table 17.  Parameter Settings: General Tab
Parameter Supported Values Default Setting Description
General Options
PMA type

FGT

FHT

FGT Selects the targeted PMA type in the F-Tile.
  • FGT supports up to 58 Gbps per lane.
  • FHT supports up to 116 Gbps per lane with maximum of four FHT PMA lanes available per tile.
Reconfiguration group

FGT supported values:

25G-1 Reconfigurable

50G-1 Reconfigurable

50G-2 Reconfigurable

100G-2 Reconfigurable

100G-4 Reconfigurable

200G-4 Reconfigurable

200G-8 Reconfigurable

400G-8 Reconfigurable

150G-6 Reconfigurable

300G-12 Reconfigurable

FHT supported values:

25G-1 Reconfigurable

50G-1 Reconfigurable

50G-2 Reconfigurable

100G-1 Reconfigurable

100G-2 Reconfigurable

100G-4 Reconfigurable

200G-2 Reconfigurable

200G-4 Reconfigurable

400G-4 Reconfigurable

25G-1 Reconfigurable

Selects the reconfiguration group. The reconfiguration group indicates the maximum supported fracture types, and data rates along with the maximum count of PMA used within the group.

PMA Mode

Duplex

TX Simplex

RX Simplex

Duplex Selects the PMA operation mode.
Enable RS-FEC use

On

Off

Off

Select if RS-FEC is enabled in any one of the subsequent profiles.

If this attribute is not selected all RS-FEC related attributes in all profiles are grayed out for all profiles.
System PLL frequency

31.25MHz - 1000MHz

830.078125

Sets system PLL output clock frequency.

Number of secondary profiles 1-32 1 Selects the number for the secondary profiles.

Each secondary profile enables a new tab in the IP GUI. For example, setting value of profiles to 8 generates eight secondary profile tabs.

Datapath Avalon® Memory-Mapped Interface Options
Enable datapath Avalon® interface

On

Off

Off Enables or disables datapath Avalon® interface.
Enable soft CSR

On

Off

Off Turns the soft CSR feature on or off.
Enable reconfiguration soft CSR

On

Off

Off Turns the reconfiguration soft CSR feature on or off.
Enable readdatavalid port on datapath Avalon® interface

Off

On

Off

Off specifies no readdatavalid port, and waitrequest low indicates data valid.

On specifies readdatavalid port indicates data valid.

Enable Debug Endpoint on datapath Avalon® interface

On

Off

Off When enabled, IP includes an embedded Debug Master Endpoint that connects internally Avalon® memory-mapped slave interface. The Debug Master Endpoint can access the reconfiguration space of the FEC. It can perform certain test and debug functions via JTAG using System Console. This option may require you to include a jtag_debug link in the system.
PMA Avalon® Memory-Mapped Interface Options
Enable PMA Avalon® interface

On

Off

Off

Enables or disables PMA Avalon® interface.

Enable readdatavalid port on PMA Avalon® interface

On

Off

Off

Off specifies no readdatavalid port, and waitrequest low indicates data valid.

On specifies readdatavalid port indicates data valid.

Enable Debug Endpoint on PMA Avalon® interface

On

Off

Off

When enabled, IP includes an embedded Native PHY Debug Master Endpoint that connects internally to the Avalon memory-mapped slave interface. The Native PHY Debug Master Endpoint can access the reconfiguration space of the PMA lane.

Figure 2. IP Parameter Editor: Profile #0
Table 18.  Parameter Settings: Profile #N (N=0-32) Tab
Parameter Supported Values Default Setting Description
Target fracture

All

0-32

All A profile can define a portion of the reconfiguration subset, for example in 100G reconfiguration group, one of the 50G subsets could be defined by this profile. When All is selected this profile is instantiated multiple times and is targeted to all PMAs. Otherwise it is be applied to selected PMA. For multi-PMA profiles, the profile is applied to PMAs consecutively starting from base profile.
Profile group id 0:32 0 The setting should be allocated to each profile configuration based on total number of available sub-set profiles and what id you choose to assign to each profile.
Use profile for startup

On

Off

N/A When enabled, this profile becomes part of start-up configuration..
FGT PMA Configuration rules

Basic

OTN

CPRI

GPON

SDI

SONET

SATA

Basic Selects the protocol configuration rules for the FGT PMA. Parameter needs to be set for individual PMAs.
PMA Modulation type

NRZ

PAM4

PAM4

Specifies the modulation type used for serial data.
PMA Data Rate
FHT
  • 24-29 Gbps NRZ
  • 48-58 Gbps NRZ and PAM4
  • 96-116 Gbps PAM4
FGT
  • 1-32 Gbps NRZ
  • 20-158.125 PAM4

26562.5

Specifies the PMA data rate in units of Mbps.

PMA Width

8

10

16

20

32

64

128

32 Specifies the PMA data width.
Figure 3. IP Parameter Editor: Secondary Profiles #1-32
Table 19.  Additional Parameter Settings for Secondary Profiles: Profile #N (N=1-32) Tab
Parameter Supported Values Default Setting Description
Copy from reference profile to profileN N/A N/A When you click this button, the parameter settings of the Reference profile are copied to current profile.
Enable separate reference clock ports for profile
Note: This parameter is available only for secondary profiles.
N/A N/A By default only the reference clock ports for base profile are available at top level. All other PMAs gets the same reference clocks as the base profile. When this option is selected, reference clock ports are available for secondary profiles. When you have different reference clock connections for the same PMAs in different profiles, Quartus® Prime Pro Edition software detects the intent for reference clock switching.
Figure 4. IP Parameter Editor: TX FGT Datapath Options P0
Table 20.  Parameter Settings: TX FGT Datapath Options PN (N=0-32)
Parameter Supported Values Default Setting Description
TX FGT PMA PN (N=0-32)
Enable Gray Coding

On

Off

Off Enables Gray coding. Applicable for PAM4 encoding only.
Enable precoding

On

Off

Off Enables precoding. Applicable to PAM4 encoding only.
Enable fgt_tx_beacon port

On

Off

Off Enable fgt_tx_beacon port for SATA.
TX User Clock Setting PN (N=0-32)
Enable TX user clock 1

On

Off

Off Controls the buffer to enable/disable TX user clock 1. If the clock is not used you can disable setting to save power.
Enable TX user clock 2

On

Off

Off Controls the buffer to enable/disable TX user clock 2. If the clock is not used you can disable setting to save power.
TX user clk div by

12-139.5

32 Division factor from Fvco of TX PLL to TX user clock. Values from 12 to 139.5 are acceptable in 0.5 increments. This clock source drives both TX user clock 1 and 2
TX FGT PLL Settings PN (N=0-32)
Output frequency Output Displays preset frequency Shows the calculated TX FGT PLL output frequency.
VCO frequency Output Displays preset frequency Shows the calculated TX FGT PLL VCO output frequency.
Enable TX FGT PLL cascade mode

On

Off

Off In single lane configurations, selects the mode where RX CDR PLL gets its reference clock from TX PLL output. In multi-lane configurations, selects the mode where RX CDR PLL of initiators and responders get their reference clock from initiator TX PLL output and TX PLL of responders get their reference clocks from initiator TX PLL output.
Enable TX FGT PLL fractional mode

On

Off

Off Enables TX FGT PLL’s fractional mode.
TX FGT PLL reference clock frequency 25 to 380 MHz 156.25 MHz Selects the reference clock frequency (MHz) for the TX FGT PLL. Range is:
  • 25 – 380 MHz when reference clock is configured for FGT PMA. (If using HDMI protocol, use only 25 – 100 MHz)
  • 100 – 380 MHz when reference clock is configured for System PLL or shared with system PLL and FGT PMA.
TX PMA Interface P0
Note: These interface ports are only available in the base profile (Profile #0) tab.
Enable tx_pmaif_fifo_empty port

On

Off

Off Enables the port which indicates TX PMA Interface FIFO's empty condition.
Enable tx_pmaif_fifo_pempty port

On

Off

Off Enable the port which indicates TX PMA Interface FIFO's partially empty condition.
Enable tx_pmaif_fifo_pfull port

On

Off

Off Enables the port which indicates TX PMA Interface FIFO's partially full condition.
TX Core Interface PN (N=0-32)
TX Clock Options PN (N=0-32)
Selected tx_clkout clock source

Word Clock

Bond Clock

User Clock 1

User Clock 2

Sys PLL clock

Sys PLL Clock Div2

Sys PLL Clock Div2

Specifies the tx_clkout output port source.

Frequency of tx_clkout Output Displays frequency value

Displays the frequency of tx_clkout in MHz based on tx_clkout source selection

Enable tx_clkout2 port
Note: This parameter is available only in the base profile (Profile #0) as it is related to port selection.

On

Off

Off

Enables the optional tx_clkout2 output clock.

Selected tx_clkout2 clock source

Word Clock

Bond Clock

User Clock 1

User Clock 2

Sys PLL clock

Sys PLL Clock Div2

Word Clock

Specifies the tx_clkout2 output port source.

tx_clkout2 clock divby

1

2

4

1

Selects the tx_clkout2 divider setting that divides the tx_clkout2 output port source.

Frequency of tx_clkout2 Output Displays frequency value

Displays the frequency of tx_clkout2 in MHz based on tx_clkout2 source selection and tx_clkout2 clock divide by factor.

Figure 5. IP Parameter Editor: TX FHT Datapath Options P0
Table 21.  Parameter Settings: TX FHT Datapath Options PN (N=0-32)
Parameter Supported Values Default Setting Description
TX FHT PMA PN (N=0-32)
Enable FHT TX P&N Invert Disabled/Enabled Disabled Enable this to invert TX P and N output.
Select FHT Lane PLL refclk source 100, 156.25 156.25 Selects the FHT Lane PLL refclk source.
  • 100 selects 100 MHz output from common PLL to lane PLL.
  • 156.25 selects 156.25 MHz output from common PLL to lane PLL.
FHT user clk div33_34 select

DIV_33

DIV_34

DIV_33_BY_2

DIV_34_BY_2

DIV_33_BY_2

Selects one of the four DIV clock output for the TX user clock. Refer to Clocking for more details on how to use this output.
Enable FHT TX pre-encoder

On

Off

Off Enables FHT TX pre-encoder. This setting must match the link partner's RX pre-encoder setting.
Enable FHT PLL pre-divider

On

Off

Off Enables FHT PLL pre-divider. If disabled, pre-divider value is 1 and if enabled pre-divider value is 2. In certain configurations, where disabling this sets the lane PLL to fractional mode, you must enable this to set the lane PLL in integer mode for better performance.
Enable FHT TX user clk1

On

Off

Off Enables the FHT TX user clk1.
FHT TX user clk1 select DIV3334

DIV40

DIV3334 FHT TX user clk1 select, you can select DIV3334 (one of the four DIV clocks listed in user div33_34) or DIV40 clock. Refer to Clocking for more information.
Enable FHT TX user clk2

On

Off

Off Enables FHT TX user clk2.
FHT TX user clk2 select DIV3334

DIV40

DIV3334 FHT TX user clk2 select, you can select DIV3334 or DIV40 clock. Default value is . Refer to Clocking for more information.
Figure 6. IP Parameter Editor: RX FGT Datapath Options P0
Table 22.  Parameter Settings: RX FGT Datapath Options PN (N=0-32)
Parameter Supported Values Default Setting Description
RX FGT PMA PN (N=0-32)
Enable Gray Coding

On

Off

Off Enables Gray coding. Applicable for PAM4 encoding only.
Enable precoding

On

Off

Off Enables precoding. Applicable to PAM4 encoding only.
Enable SATA squelch detection

On

Off

Off Enables squelch detection for SATA.
Enable fgt_rx_signal_detect port

On

Off

Off Enables the fgt_rx_signal_detect port.
Enable fgt_rx_signal_detect_lfps port

On

Off

Off Enables the fgt_rx_signal_detect_lfps port.
RX FGT CDR Settings PN (N=0-32)
Output frequency N/A Displays preset frequency Specifies the non editable RX FGT CDR output frequency initial value derived from the IP configuration.
VCO frequency N/A Displays preset frequency Specifies the non editable RX FGT CDR VCO output frequency initial value derived from the IP configuration.
RX FGT CDR reference clock frequency 25.781250-250.000000 156.25 MHz Selects the reference clock frequency for the CDR.
Enable fgt_rx_set_locktoref port

On

Off

Off Asserting this signal keeps CDR in lock to reference mode. Deasserting this signal keeps CDR in auto mode. When switching modes, assert reset. In manual reference clock mode, switch the reset controller to ignore locktodata mode through appropriate write to soft CSRs.
Enable fgt_rx_cdr_freeze port

On

Off

Off This port is for GPON to freeze the CDR lock state during non-active time-slots.
CDR lock mode

auto

manual lock to reference

auto

When auto is selected, during the user-initiated reset (or power-up) CDR first tries to lock to data if present. By default, loss of lock to data re-triggers the RX PMA reset.

When manual lock to reference is selected, fgt_rx_set_locktoref controls the CDR lock behavior. If fgt_rx_set_locktoref is low, CDR operates in auto mode. If fgt_rx_set_locktoref is high CDR operates in lock to reference mode. In manual mode, the reset controller should be configured to ignore the lock to data status through appropriate soft CSR write.

RX User Clock Setting PN (N=0-32)
Enable RX user clock

On

Off

Off Divider values of RX CDR output frequency. If the clock is not used, you can disable the clock to save power. This clock source drives both RX User Clock 1 and User Clock 2 in the Core Interface.
RX user clock div by: 12-139.5 32 Division factor from Fvco of RX CDR to RX user clock. Values from 12 to 139.5 are acceptable in 0.5 increments.
RX PMA Interface P0
Note: These interface ports are only available in the base profile (Profile #0) tab.
Enable rx_pmaif_fifo_empty port

On

Off

Off Enables the port that indicates RX PMA Interface FIFO's empty condition.
Enable rx_pmaif_fifo_pempty port

On

Off

Off Enable the port that indicates RX PMA Interface FIFO's partially empty condition.
Enable rx_pmaif_fifo_pfull port

On

Off

Off Enables the port that indicates RX PMA Interface FIFO's partially full condition.
RX Core Interface PN (N=0-32)
RX Clock Options PN (N=0-32)
Selected rx_clkout clock source

Word Clock

Bond Clock

User Clock 1

User Clock 2

Sys PLL clock

Sys PLL Clock Div2

Sys PLL Clock Div2

Specifies the rx_clkout output port source.

Frequency of rx_clkout Output Displays frequency value

Displays the frequency of rx_clkout in MHz based on rx_clkout source selection

Enable rx_clkout2 port
Note: This parameter is available only in the base profile (Profile #0) as it is related to port selection.

On

Off

Off

Enables the optional rx_clkout2 output clock.

Selected rx_clkout2 clock source

Word Clock

Bond clock

User clock 1

User clock 2

Sys PLL clock

Sys PLL Clock div2

Word Clock

Specifies the rx_clkout2 output port source.

rx_clkout2 clock divby

1

2

1

Selects the rx_clkout2 divider setting that divides the rx_clkout2 output port source.

Frequency of rx_clkout2 Output Displays frequency value

Displays the frequency of rx_clkout2 in MHz based on rx_clkout2 source selection and rx_clkout2 clock divide by factor.

Figure 7. IP Parameter Editor: RX FHT Datapath Options P0
Table 23.  Parameter Settings: RX FHT Datapath Options PN (N=0-32)
Parameter Supported Values Default Setting Description
RX FHT PMA PN (N=0-32)
Enable FHT RX PAM4 Level Alternative Coding

On

Off

Off Enable this for RX PAM4 Level Alternative Coding. When disabled, link partner must send gray code set to 0xB4. When enabled, link partner must send gray code set to 0x6C. You must disable this parameter for normal operation or when in internal or external loopback.
Enable FHT RX P&N Invert Disabled/Enabled Disabled Enable this to invert RX P and N input.
Enable FHT RX data profile Disabled/Enabled Enabled Enable FHT RX data profile to set the threshold for number of 1’s in 1M RX Data bits that determine the quality of RX data. If the number of 1's received is not within the specified min and max threshold, then RX bad status is indicated.
Note: This parameter must be Enabled.
FHT RX user clk div33_34 select

RX_DIV_33

RX_DIV_34

RX_DIV_33_BY_2

RX_DIV_34_BY_2

RX_DIV_33_BY_2 Selects one of the four DIV clock output for the RX user clock. Refer to Clocking for more information.
Enable FHT RX pre-encoder

On

Off

Off Enables FHT TX pre-encoder. This setting must match the link partner's RX pre-encoder setting.
Enable FHT RX user clk1

On

Off

Off Enables FHT RX user clk1.
FHT RX user clk1 select

DIV3334

DIV40

DIV3334 FHT RX user clk1 select. Refer to Clocking for more information.
Enable FHT RX user clk2

On

Off

Off Enables FHT RX user clk2.
FHT RX user clk2 select

DIV3334

DIV40

DIV3334 FHT RX user clk2 select. Refer to Clocking for more information.
Figure 8. IP Parameter Editor: RS-FEC P0
Table 24.  Parameter Settings: RS-FEC PN (N=0-32)
Parameter Supported Values Default Setting Description
Enable RS-FEC

On

Off

Off
Enables the RS-FEC module.
RS-FEC Mode:
  • Ethernet Technology Consortium (ETC) RS (272,258)
  • IEEE 802.3 RS (528,514) (CL 91)
  • IEEE 802.3 RS (544,514) (CL 91) ETC
  • Fibre Channel RS (528, 514)
  • FlexO RS (528, 514)
  • IEEE 802.3 RS (544,514) (CL 134)
  • Custom IEEE 802.3 RS (544, 514) (CL 134) @26.5625Gbps
  • Interlaken RS (544, 514)
  • Fibre Channel RS (544, 514)
  • FlexO RS (544, 514)
IEEE 802.3 RS (528,514) (CL 91)

Specifies the RS-FEC mode for various topologies.

Enable RS-FEC data interleave pattern

On

Off

Off

FEC lanes are bit-interleaved on each physical lane. When enabled: 64/80 (only for IEEE 802).

Note: The F-Tile PMA/FEC Direct PHY Multirate Intel FPGA IP does not support RS-FEC loopback.
Figure 9. IP Parameter Editor: FGT Analog Parameters PN (N=0-32)
Table 25.  Parameter Settings: FGT TX Equalization (EQ) PN (N=0-32)
Parameter Values Default Setting Description
FGT TXEQ Post Tap 1, 1.0 step size 0 to 19 0 Options for FGT TX EQ Post Tap 1, in 1.0 step size increments.
FGT TXEQ Pre Tap 1, 1.0 step size 0 to 15 5 Options for FGT TX EQ Pre Tap 1, in 1.0 step size increment
FGT TXEQ Pre Tap 2, 1.0 step size 0 to 7 0

Options for FGT TX EQ Pre Tap 2, in 1.0 step size increments.

FGT TXEQ Main Tap, 1.0 step size 0 to 55 35 Options for FGT TX EQ Main Tap, in 1.0 step size increments.
Table 26.  Parameter Settings: FGT RX PN (N=0-32)
Parameter Values Default Setting Description
Select FGT RX Onchip Termination RX_ONCHIP_TERMINATION_R_1(85 Ohms)

RX_ONCHIP_TERMINATION_R_2(100 ohms)

RX_ONCHIP_TERMINATION_R_1(85 Ohms) Selects FGT RX termination resistor setting.
Enable FGT RX AC Couple DISABLE

ENABLE

ENABLE Enable RX external AC coupling setting.
Enable FGT VSR mode VSR_MODE_LOW_LOSS

VSR_MODE_HIGH_LOSS

VSR_MODE_DISABLE

VSR_MODE_LOW_LOSS Enable VSR mode setting.
RXEQ VGA Gain 0 to 63 0 Options for RX EQ VGA gain value, in 1.0 step size increments.
Note: This parameter is only available when the Adaptation mode is set to manual in RX Datapath Options.
RXEQ High Frequency Boost 0 to 63 0 Options for RX EQ high frequency boost value, in 1.0 step size increments.
Note: This parameter is only available when the Adaptation mode is set to manual in RX Datapath Options.
RXEQ DFE Data Tap1 0 to 63 0 Options for RX EQ DFE data tap1 value, in 1.0 step size increments.
Note: This parameter is only available when the Adaptation mode is set to manual in RX Datapath Options.
Figure 10. IP Parameter Editor: FHT Analog Parameters PN (N=0-32)
Table 27.  Parameter Settings: FHT TX PN (N=0-32)
Parameter Values Default Setting Description
Enable FHT TX P&N Invert Disabled

Enabled

Disabled Enable FHT TX P and N inversion.
Enable FHT TXOUT Tristate Disabled

Enabled

Disabled Enable tristate on FHT TX serial outputs.
Select FHT TX Termination TXTERM_OFFSET_P0(90 Ohms)

TXTERM_OFFSET_M1(96.8 Ohms)

TXTERM_OFFSET_P0(90 Ohms) Selects FHT TX termination resistor setting.
Table 28.  Parameter Settings: FHT TX Equalization (EQ) PN (N=0-32)
Parameter Values Default Setting Description

Post-Cursor 4, 0.25 step size

-8.0 to +7.75 0.0 FHT post tap 4 coefficients, 0.25 step size.
Post-Cursor 3, 0.25 step size -8.0 to +7.75 0.0 FHT post tap 3 coefficients, 0.25 step size.
Post-Cursor 2, 0.25 step size -8.0 to +7.75 0.0 FHT post tap 2 coefficients, 0.25 step size.
Post-Cursor 1, 0.5 step size -16.0 to +15.5 0.0 FHT post tap coefficient, 0.5 step size.
Main-Cursor,0.5 step size 0.0 to 41.5 41.5 FHT main tap coefficient, 0.5 step size.
Pre-Cursor 1,0.5 step size -16.0 to +15.5 0.0 FHT pre tap 1 coefficient, 0.5 step size.
Pre-Cursor 2,0.25 step size -8.0 to +7.75 0.0 FHT pre tap 2 coefficients, 0.25 step size.
Pre-Cursor 3,0.25 step size -8.0 to +7.75 0.0 FHT pre tap 3 coefficients, 0.25 step size.
Table 29.  Parameter Settings: FHT RX PN (N=0-32)
Parameter Values Default Setting Description
Enable FHT RX P&N Invert Disabled

Enabled

Disabled Enable FHT RX P and N inversion.
Select FHT RX Termination RXTERM_OFFSET_P0(90 Ohms)

RXTERM_OFFSET_P2(94.6 Ohms)

RXTERM_OFFSET_P3(97.7 Ohms)

RXTERM_OFFSET_P4(100 Ohms)

RXTERM_OFFSET_P5(102.3 Ohms)

RXTERM_OFFSET_P6(105.4 Ohms)

RXTERM_OFFSET_P7(107.7 Ohms)

RXTERM_OFFSET_P8(110 Ohms)

RXTERM_OFFSET_M4(80.8 Ohms)

RXTERM_OFFSET_M5(83.1 Ohms)

RXTERM_OFFSET_M6(85.4 Ohms)

RXTERM_OFFSET_M7(87.7 Ohms)

RXTERM_OFFSET_P0(90 Ohms) Selects FHT RX termination resistor setting.
Select FHT external AC Cap EXTERNAL_AC_CAP_ENABLE

EXTERNAL_AC_CAP_DISABLE

EXTERNAL_AC_CAP_ENABLE Enable external AC coupling capacitance.