FIR II IP Core: User Guide

Download PDF
ID 683208
Date 6/12/2020
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. About the FIR II IP Core 2. FIR II IP Core Getting Started 3. FIR II IP Core Parameters 4. FIR II IP Core Functional Description 5. Document Revision History for the FIR II IP User Guide A. FIR II IP Core Document Archive
1. About the FIR II IP Core x
1.1. DSP Intel® FPGA IP Features 1.2. FIR II IP Core Features 1.3. FIR II IP Device Support 1.4. DSP Intel® FPGA IP Verification 1.5. FIR II IP Core Release Information 1.6. FIR II IP Core Performance and Resource Utilization
2. FIR II IP Core Getting Started x
2.1. Installing and Licensing Intel® FPGA IP Cores 2.2. IP Catalog and Parameter Editor 2.3. Specifying the IP Core Parameters and Options ( Intel® Quartus® Prime Pro Edition) 2.4. Simulating Intel® FPGA IP Cores 2.5. Simulating the FIR II IP Core Testbench in MATLAB 2.6. DSP Builder for Intel® FPGAs Design Flow
2.1. Installing and Licensing Intel® FPGA IP Cores x
2.1.1. Intel® FPGA IP Evaluation Mode 2.1.2. FIR II IP Core Intel® FPGA IP Evaluation Mode Timeout Behavior
2.3. Specifying the IP Core Parameters and Options ( Intel® Quartus® Prime Pro Edition) x
2.3.1. IP Core Generation Output ( Intel® Quartus® Prime Pro Edition)
3. FIR II IP Core Parameters x
3.1. FIR II IP Core Filter Specification 3.2. FIR II IP Core Coefficient Settings 3.3. FIR II IP Core Coefficients 3.4. FIR II IP Core Input and Output Options 3.5. FIR II IP Core Implementation Options 3.6. FIR II IP Core Reconfigurability
3.3. FIR II IP Core Coefficients x
3.3.1. Loading Coefficients from a File
3.4. FIR II IP Core Input and Output Options x
3.4.1. Signed Fractional Binary 3.4.2. MSB and LSB Truncation, Saturation, and Rounding
3.5. FIR II IP Core Implementation Options x
3.5.1. Memory and Multiplier Trade-Offs
3.5.1. Memory and Multiplier Trade-Offs x
3.5.1.1. Using Memory Block Threshold 3.5.1.2. Using Dual-port RAM Threshold 3.5.1.3. Using Large RAM Threshold 3.5.1.4. Using Hard Multiplier Threshold
4. FIR II IP Core Functional Description x
4.1. FIR II IP Core Interpolation Filters 4.2. FIR Decimation Filters 4.3. FIR II IP Core Time-Division Multiplexing 4.4. FIR II IP Core Multichannel Operation 4.5. FIR II IP Core Multiple Coefficient Banks 4.6. FIR II IP Core Coefficient Reloading 4.7. Reconfigurable FIR Filters 4.8. FIR II IP Core Interfaces and Signals
4.4. FIR II IP Core Multichannel Operation x
4.4.1. Vectorized Inputs 4.4.2. Channelization 4.4.3. Channel Input and Output Format
4.4.3. Channel Input and Output Format x
4.4.3.1. Eight Channels on Three Wires 4.4.3.2. Four Channels on Four Wires 4.4.3.3. 15 Channels with 15 Valid Cycles and 17 Invalid Cycles 4.4.3.4. 22 Channels with 11 Valid Cycles and 9 Invalid Cycles 4.4.3.5. Super Sample Rate
4.8. FIR II IP Core Interfaces and Signals x
4.8.1. Avalon Streaming Interfaces in DSP Intel FPGA IP 4.8.2. FIR II IP Core Avalon-ST Interfaces 4.8.3. FIR II IP Core Signals
4.8.2. FIR II IP Core Avalon-ST Interfaces x
4.8.2.1. Avalon-ST Sink Interface 4.8.2.2. Avalon-ST Source Interface
4.8.2.1. Avalon-ST Sink Interface x
4.8.2.1.1. Single Channel on Single Wire 4.8.2.1.2. Multiple Channels on Single Wire 4.8.2.1.3. Multiple Channels on Multiple Wires
1. About the FIR II IP Core
2. FIR II IP Core Getting Started
3. FIR II IP Core Parameters
4. FIR II IP Core Functional Description
5. Document Revision History for the FIR II IP User Guide
A. FIR II IP Core Document Archive

3.5.1.4. Using Hard Multiplier Threshold

This FIR II IP core threshold is the trade-off between hard and soft multipliers. For devices that support hard multipliers or DSP blocks, use these resources instead of a soft multiplier made from LEs.
For example, a 2-bit × 10-bit multiplier consumes very few LEs. The hard multiplier threshold value corresponds to the number of LEs that save a multiplier. If the hard multiplier threshold value is 100, you are allowing 100 LEs. Therefore, an 18 × 18 multiplier (that requires approximately 182–350 LEs) does not transfer to LEs because it requires more LEs than the threshold value. However, the IP core implements a 16 × 4 multiplier that requires approximately 64 LEs as a soft multiplier with this setting.
  1. Set the default to always use hard multipliers. With this value, IP core implements a 24 × 18 multiplier as two 18 × 18 multipliers.
  2. Set a value of approximately 300 to keep 18 × 18 multipliers hard, but transform smaller multipliers to LEs. The IP core implements a 24 × 18 multiplier as a 6 × 18 multiplier and an 18 × 18 multiplier, so this setting builds the hybrid multipliers that you require.
  3. Set a value of approximately 1,000 to implement the multipliers entirely as LEs. Essentially, you are allowing a high number (1000) of LEs to save using an 18 × 18 multiplier.
  4. Set a value of approximately 10 to implement a 24 × 16 multiplier as a 36 × 36 multiplier. With the value, you are not even allowing the adder to combine two multipliers. Therefore, the system has to use a 36 × 36 multiplier in a single DSP block.
Level Two Title