Symmetric Cryptographic Intel FPGA Hard IP User Guide

Download PDF
ID 714305
Date 10/02/2023
Public
Document Table of Contents
Document Table of Contents x
1. Introduction 2. Interface Overview 3. Parameters 4. Designing with the IP Core 5. Block Description 6. Cryptographic IP Data Profiles 7. Configuration Registers 8. Design Example 9. Symmetric Cryptographic Intel FPGA Hard IP User Guide Archives 10. Document Revision History for the Symmetric Cryptographic Intel FPGA Hard IP User Guide
1. Introduction x
1.1. Terminology 1.2. IP Core Overview 1.3. Release Information 1.4. Device Family Support 1.5. Resource Utilization
1.2. IP Core Overview x
1.2.1. IP Core Applications
2. Interface Overview x
2.1. Clock Signals 2.2. Reset Signals 2.3. AXI-ST Interface 2.4. AXI-Lite Interface
4. Designing with the IP Core x
4.1. Installing and Licensing Intel® FPGA IP Cores 4.2. Specifying the IP Core Parameters and Options 4.3. Generated File Structure 4.4. Symmetric Cryptographic IP Core Flow 4.5. Dynamically Disabling SM4 Capability 4.6. Error Handling 4.7. Error Reporting 4.8. Resetting the IP Core 4.9. Channel Definition and Allocation 4.10. Byte Ordering 4.11. AXI-ST Single Packet Mode 4.12. AXI-ST Multiple Packet Mode
4.1. Installing and Licensing Intel® FPGA IP Cores x
4.1.1. Intel® FPGA IP Evaluation Mode
4.6. Error Handling x
4.6.1. Detected Error Handling 4.6.2. Key RAM ECC Error Handling
5. Block Description x
5.1. Reset Sequencer 5.2. AXI-ST Ready Latency 5.3. AXI Adapter 5.4. Integrity Check Value Comparison 5.5. GCM Padding and Depadding
5.3. AXI Adapter x
5.3.1. MAC Packing 5.3.2. Data Last Indicator 5.3.3. Stream and Channel ID Buffering 5.3.4. TKEEP and LAST_SEGMENT Signals Generation 5.3.5. MAC Dropping on Decryption
5.5. GCM Padding and Depadding x
5.5.1. GCM Padding 5.5.2. GCM Depadding
6. Cryptographic IP Data Profiles x
6.1. MAC Security Profile (MACsec) 6.2. IP Security Profile (IPsec) 6.3. Generic GCM Profile (GCM) 6.4. Generic XTS Profile (XTS)
6.1. MAC Security Profile (MACsec) x
6.1.1. MACsec Flow 6.1.2. AXI-ST Interface Using MAC Security (MACsec) Profile Pattern
6.2. IP Security Profile (IPsec) x
6.2.1. AXI-ST Interface Using IP Security (IPsec) Profile Pattern
6.3. Generic GCM Profile (GCM) x
6.3.1. AXI- ST Interface Using Generic GCM Profile Pattern
6.4. Generic XTS Profile (XTS) x
6.4.1. AXI-ST Interface Using Generic XTS Profile Pattern
8. Design Example x
8.1. Functional Description 8.2. Crypto VSIP Top Block Descriptions 8.3. Test Configurations 8.4. Software Requirements 8.5. Simulation Requirements 8.6. Steps to Generate the Design Example 8.7. Running Simulation Tests 8.8. Running Hardware Tests
8.2. Crypto VSIP Top Block Descriptions x
8.2.1. Clock and Reset 8.2.2. Host Interface
8.7. Running Simulation Tests x
8.7.1. Steps to Simulate the Design Example
8.8. Running Hardware Tests x
8.8.1. Supported Boards 8.8.2. Steps to Compile the Design Example for Hardware 8.8.3. Steps to Run the Design Example on Hardware
1. Introduction
2. Interface Overview
3. Parameters
4. Designing with the IP Core
5. Block Description
6. Cryptographic IP Data Profiles
7. Configuration Registers
8. Design Example
9. Symmetric Cryptographic Intel FPGA Hard IP User Guide Archives
10. Document Revision History for the Symmetric Cryptographic Intel FPGA Hard IP User Guide

5.3.2. Data Last Indicator

This section specifies the conditions for inserting the data_last_indicator signal.

When you select the Generic XTS profile, the Symmetric Cryptographic IP core must assert the data_last_indicator signal on the 2nd last data cycle to indicate the last clock cycle that requires CTS. The last clock cycle indicates through the tlast signal that CTS is required when the valid bytes within the last clock cycle are not a multiple of 16 bytes.

The below example depicts an AXI-ST interface request sent to the Symmetric Cryptographic IP core using a generic XTS profile. The last clock cycle of the request contains 4 bytes of a valid payload. When the soft logic sends the request to the AES/SM4 Inline Cryptographic Accelerator, the soft logic asserts the data_last_indicator signal one cycle before the last clock cycle. If CTS is expected in the next clock cycle, you must assert this signal. You must send the last two data cycles back-to-back if CTS is expected.

Table 27.  Generic XTS Profile Example: Asserting tlast Signal
Important: You must assert tlast when you expect the CTS in the next clock cycle.
Profile Generic XTS Generic XTS Generic XTS Generic XTS
tvalid 1 1 1 0
tlast 0 0 1 0
tkeep All 1s All 1s

0000_0000

0000_0000

0000_0000

0000_0000

0000_0000

0000_0000

0000_0000

0000_0000

0000_1111

 All 0s
DATA
tdata[127:0] Data 1 Data 5 {0, Data 9[32:0]} IDLE
tdata[255:128] Data 2 Data 6 IDLE IDLE
tdata[391:256] Data 3 Data 7 IDLE IDLE
tdata[511:392] Data 4 Data 8 IDLE IDLE
Level Two Title