4.3.1.10. Transceiver Native PHY (TX)

HDMI Intel® FPGA IP User Guide

Download PDF

ID 683798

Date 12/04/2023

Version

Public

Visible to Intel only — GUID: vgo1441790426547

Ixiasoft

View Details

4.3.1.10. Transceiver Native PHY (TX)

The Arria V and Stratix V Transceiver Native PHY (TX) configuration settings are typically the same as RX.

Table 16. Arria V and Stratix V Transceiver Native PHY (TX) Configuration Settings (6,000 Mbps)This table shows an example of Arria V and Stratix V Transceiver Native PHY (TX) configuration settings for TMDS bit rate of 6,000 Mbps.
Parameters	Settings
Datapath Options
Enable TX datapath	On
Enable RX datapath	Off
Enable Standard PCS	On
Initial PCS datapath selection	Standard
Number of data channels	4
Bonding mode	xN
Enable simplified data interface	On
TX PMA
Data rate	6,000 Mbps
TX local clock division factor	1
Enable TX PLL dynamic reconfiguration	On
Use external TX PLL	Off
Number of TX PLLs	1
Main TX PLL logical index	0
Number of TX PLL reference clocks	1
PLL type	CMU
Reference clock frequency	600 MHz
Selected reference clock source	0
Selected clock network	xN
Standard PCS
Standard PCS protocol	Basic
Standard PCS/PMA interface width	10 (for 1 symbol per clock) 20 (for 2 and 4 symbols per clock)
Enable TX byte serializer	Off (for 1 and 2 symbols per clock) On (for 4 symbols per clock)

Table 17. Arria V and Stratix V Transceiver Native PHY (TX) Common Interface PortsThis table describes the Arria V and Stratix V Transceiver Native PHY (TX) common interface ports.
Signals	Direction	Description
Clocks
`tx_pll_refclk`	Input	The reference clock input to the TX PLL.
`tx_std_clkout[3:0]`	Output	TX parallel clock output.
`tx_std_coreclkin[3:0]`	Input	TX parallel clock that drives the write side of the TX phase compensation FIFO. Connect to `tx_std_clkout[0]` ports.
Resets
`tx_analogreset[3:0]`	Input	When asserted, resets all the blocks in TX PMA. Connect to Transceiver PHY Reset Controller (TX) IP core.
`tx_digitalreset[3:0]`	Input	When asserted, resets all the blocks in TX PCS. Connect to the Transceiver PHY Reset Controller (TX) IP core.
TX PLL
`pll_powerdown`	Input	When asserted, resets the TX PLL. Connect to the Transceiver PHY Reset Controller (TX) IP core.
`pll_locked`	Output	When asserted, indicates that the TX PLL is locked. Connect to the Transceiver PHY Reset Controller (TX) IP core.
PCS Ports
`unused_tx_parallel_data`	Input	Leave unconnected.
`tx_parallel_data[S410-1:0]`	Input	PCS TX parallel data. Note: S=Symbols per clock.
PMA Port
`tx_serial_data[3:0]`	Output	TX differential serial output data.
Calibration Status Port
`tx_cal_busy[3:0]`	Output	When asserted, indicates that the initial TX calibration is in progress. This port is also asserted if the reconfiguration controller is reset. Connect to the Transceiver PHY Reset Controller (TX) IP core.
Reconfiguration Ports
`reconfig_to_xcvr[349:0]`	Input	Reconfiguration signals from the Transceiver Reconfiguration Controller.
`reconfig_from_xcvr[229:0]`	Output	Reconfiguration signals to the Transceiver Reconfiguration Controller.

Select Your Language

Using Intel.com Search

Quick Links

Recent Searches

Advanced Search

Only search in

HDMI Intel® FPGA IP User Guide

4.3.1.10. Transceiver Native PHY (TX)