Stratix® 10 Embedded Memory User Guide

Download PDF
ID 683423
Date 3/29/2024
Public
Document Table of Contents
Document Table of Contents x
1. Stratix® 10 Embedded Memory Overview 2. Stratix® 10 Embedded Memory Architecture and Features 3. Stratix® 10 Embedded Memory Design Considerations 4. Stratix® 10 Embedded Memory IP References 5. Intel Stratix 10 Embedded Memory Design Example 6. Stratix® 10 Embedded Memory User Guide Archives 7. Document Revision History for the Stratix® 10 Embedded Memory User Guide
1. Stratix® 10 Embedded Memory Overview x
1.1. Stratix® 10 Embedded Memory Features
2. Stratix® 10 Embedded Memory Architecture and Features x
2.1. Byte Enable in Stratix® 10 Embedded Memory Blocks 2.2. Address Clock Enable Support 2.3. Asynchronous Clear and Synchronous Clear 2.4. Memory Blocks Error Correction Code (ECC) Support 2.5. Force-to-Zero 2.6. Coherent Read Memory 2.7. Freeze Logic 2.8. True Dual Port Dual Clock Emulator 2.9. 'X' Propagation Support in Simulation 2.10. Stratix® 10 Supported Embedded Memory IPs 2.11. Stratix® 10 Embedded Memory Clocking Modes 2.12. Stratix® 10 Embedded Memory Configurations 2.13. Initial Value of Read and Write Address Registers
2.1. Byte Enable in Stratix® 10 Embedded Memory Blocks x
2.1.1. Byte Enable Controls 2.1.2. Data Byte Output 2.1.3. Byte Enable Behavior
2.4. Memory Blocks Error Correction Code (ECC) Support x
2.4.1. Parity Bit 2.4.2. ECC Parity Flip 2.4.3. ECC Read-During-Write Behavior 2.4.4. Error Correction Code Truth Table
2.6. Coherent Read Memory x
2.6.1. Forwarding Logic
2.8. True Dual Port Dual Clock Emulator x
2.8.1. Reducing the DCFIFO Depth
2.11. Stratix® 10 Embedded Memory Clocking Modes x
2.11.1. Single Clock Mode 2.11.2. Read/Write Clock Mode 2.11.3. Input/Output Clock Mode 2.11.4. Asynchronous/Synchronous Clears in Clocking Modes 2.11.5. Output Read Data in Simultaneous Read/Write 2.11.6. Independent Clock Enables in Clocking Modes
2.12. Stratix® 10 Embedded Memory Configurations x
2.12.1. Mixed-Width Port Configurations
3. Stratix® 10 Embedded Memory Design Considerations x
3.1. Consider the Memory Block Selection 3.2. Consider the Concurrent Read Behavior 3.3. Customize Read-During-Write Behavior 3.4. Consider Power-Up State and Memory Initialization 3.5. Reduce Power Consumption 3.6. Avoid Providing Non-Deterministic Input 3.7. Avoid Changing Clock Signals and Other Control Signals Simultaneously 3.8. Including the Reset Release Intel® FPGA IP in Your Design 3.9. Resource and Timing Optimization Feature in MLAB Blocks 3.10. Consider the Memory Depth Setting 3.11. Consider Registering the Memory Output
3.3. Customize Read-During-Write Behavior x
3.3.1. Same-Port Read-During-Write Mode 3.3.2. Mixed-Port Read-During-Write Mode
4. Stratix® 10 Embedded Memory IP References x
4.1. On Chip Memory RAM and ROM Intel® FPGA IPs 4.2. eSRAM Intel® FPGA IP 4.3. FIFO Intel® FPGA IP 4.4. FIFO2 Intel® FPGA IP 4.5. Shift Register (RAM-based) Intel® FPGA IP
4.1. On Chip Memory RAM and ROM Intel® FPGA IPs x
4.1.1. Release Information for RAM and ROM Intel® FPGA IPs 4.1.2. RAM: 1-PORT Intel® FPGA IP Parameters 4.1.3. RAM: 2-PORT Intel® FPGA IP Parameters 4.1.4. RAM: 4-PORT Intel® FPGA IP Parameters 4.1.5. ROM: 1-PORT Intel® FPGA IP Parameters 4.1.6. ROM: 2-PORT Intel® FPGA IP Parameters 4.1.7. RAM and ROM Interface Signals 4.1.8. Changing Parameter Settings Manually
4.1.8. Changing Parameter Settings Manually x
4.1.8.1. RAM and ROM Parameter Settings
4.2. eSRAM Intel® FPGA IP x
4.2.1. Release Information for eSRAM Intel® FPGA IP 4.2.2. eSRAM System Features 4.2.3. eSRAM Intel® FPGA IP Parameters 4.2.4. eSRAM Intel® FPGA IP Interface Signals 4.2.5. eSRAM Intel® FPGA IP Simulation Walk-Through 4.2.6. eSRAM Timing Diagrams
4.2.2. eSRAM System Features x
4.2.2.1. eSRAM Specifications 4.2.2.2. eSRAM Usage Model
4.3. FIFO Intel® FPGA IP x
4.3.1. Release Information for FIFO Intel® FPGA IP 4.3.2. Configuration Methods 4.3.3. Specifications 4.3.4. FIFO Functional Timing Requirements 4.3.5. SCFIFO ALMOST_EMPTY Functional Timing 4.3.6. FIFO Output Status Flag and Latency 4.3.7. FIFO Metastability Protection and Related Options 4.3.8. FIFO Synchronous Clear and Asynchronous Clear Effect 4.3.9. SCFIFO and DCFIFO Show-Ahead Mode 4.3.10. Different Input and Output Width 4.3.11. DCFIFO Timing Constraint Setting 4.3.12. Coding Example for Manual Instantiation 4.3.13. Design Example 4.3.14. Gray-Code Counter Transfer at the Clock Domain Crossing 4.3.15. Guidelines for Embedded Memory ECC Feature 4.3.16. FIFO Intel® FPGA IP Parameters 4.3.17. Reset Scheme
4.3.3. Specifications x
4.3.3.1. Verilog HDL Prototype 4.3.3.2. VHDL Component Declaration 4.3.3.3. VHDL LIBRARY-USE Declaration 4.3.3.4. FIFO Signals 4.3.3.5. FIFO Parameter Settings
4.3.8. FIFO Synchronous Clear and Asynchronous Clear Effect x
4.3.8.1. Recovery and Removal Timing Violation Warnings when Compiling a DCFIFO
4.3.11. DCFIFO Timing Constraint Setting x
4.3.11.1. Embedded Timing Constraint 4.3.11.2. User Configurable Timing Constraint
4.3.11.2. User Configurable Timing Constraint x
4.3.11.2.1. SDC Commands
4.4. FIFO2 Intel® FPGA IP x
4.4.1. Release Information for FIFO2 Intel® FPGA IP 4.4.2. Configuration Methods 4.4.3. Fmax Target Measuring Methodology 4.4.4. Performance Considerations 4.4.5. FIFO2 Intel® FPGA IP Features 4.4.6. FIFO2 Intel® FPGA IP Parameters 4.4.7. FIFO2 Intel® FPGA IP Interface Signals 4.4.8. Reset and Clock Schemes
4.4.5. FIFO2 Intel® FPGA IP Features x
4.4.5.1. FIFO2 Specifications
4.4.6. FIFO2 Intel® FPGA IP Parameters x
4.4.6.1. FIFO2 Parameter Settings
4.4.7. FIFO2 Intel® FPGA IP Interface Signals x
4.4.7.1. SCFIFO Signals 4.4.7.2. DCFIFO Signals
4.4.8. Reset and Clock Schemes x
4.4.8.1. Clock Domains 4.4.8.2. Reset
4.4.8.2. Reset x
4.4.8.2.1. FIFO2 Intel® FPGA IP Reset Guidelines
4.5. Shift Register (RAM-based) Intel® FPGA IP x
4.5.1. Release Information for Shift Register (RAM-based) Intel® FPGA IP 4.5.2. Shift Register (RAM-based) Intel® FPGA IP Features 4.5.3. Shift Register (RAM-based) Intel® FPGA IP General Description 4.5.4. Shift Register (RAM-based) Intel® FPGA IP Parameter Settings 4.5.5. Shift Register Ports and Parameters Setting
5. Intel Stratix 10 Embedded Memory Design Example x
5.1. FIFO and FIFO2 Design Example
5.1. FIFO and FIFO2 Design Example x
5.1.1. Generating the Design Example 5.1.2. Simulating the Design Example
5.1.2. Simulating the Design Example x
5.1.2.1. Simulation Results
1. Stratix® 10 Embedded Memory Overview
2. Stratix® 10 Embedded Memory Architecture and Features
3. Stratix® 10 Embedded Memory Design Considerations
4. Stratix® 10 Embedded Memory IP References
5. Intel Stratix 10 Embedded Memory Design Example
6. Stratix® 10 Embedded Memory User Guide Archives
7. Document Revision History for the Stratix® 10 Embedded Memory User Guide

4.4.6.1. FIFO2 Parameter Settings

Table 60.  FIFO2 Parameters Description
Parameter Description
DATAWIDTH FIFO Write and Read Data Width.

The user width granularity is as below, depending on the RAM block type:

  • M20K: 32n; where n = 1 to 128
  • MLAB: 20n; where n = 1 to 205

This allows up to 4096 bit width which should be more than enough for different applications.

All unused bits (for example, bits that do not carry any information) should be tied-off. For instance, if the user data width were 20-bit and M20K RAM block is used, there would be 12 unused bits to be tied-off.

The default value for n is 1.

SCFIFO_MODE SCFIFO Mode.

Specify whether the FIFO should operate in SCFIFO mode, in which the clock crossing logic structure between Write and Read clock domains shall be removed.

  • 1— SCFIFO mode
  • 0 (default)—DCFIFO mode
RAM_BLK_TYPE RAM Block Type.

Specify the embedded RAM blocks to be used as the main FIFO storage.

  • "M20K" (default)—Use M20K
  • "MLAB"—Use MLAB
USE_ACLR_PORT Use Asynchronous Clear Port.

Specify whether the asynchronous reset ports (for example, w_aclr and r_aclr) of the IP should have effect.

  • 1—Ports are used to asynchronously reset the IP
  • 0 (default)—Ports are not used and have no effect
WRPTR_GRY_SYNC_CHAIN_LEN Write Gray-Code Pointer Synchronizer Chain Length.

Specify the number of flop stages used to synchronize Write Gray-Code Pointer to the r_clk domain.

  • 3 (default)—Use 3-stage synchronizer
  • 4—Use 4-stage synchronizer
RDPTR_GRY_SYNC_CHAIN_LEN Read Gray-Code Pointer Synchronizer Chain Length.

Specify the number of flop stages used to synchronize Read Gray-Code Pointer to the w_clk domain.

  • 3 (default)—Use 3-stage synchronizer
  • 4—Use 4-stage synchronizer
RAM_WRPTR_DUPLICATE RAM Write Address Duplication.

Specify whether RAM Write Address and associated logic (where appropriate) should be duplicated per RAM block.

  • 1—Enable per RAM block preserve/duplication. This may increase Fmax at the expense of resources
  • 0 (default)—Do not enable per RAM block preserve/duplication. You can determine which registers should be duplicated through assignment.
RAM_RDPTR_DUPLICATE RAM Read Address Duplication.

Specify whether RAM Read Address (and associated logic where appropriate should be duplicated per RAM block. U

  • 1—Enable per RAM block preserve/duplication. This may increase Fmax at the expense of resources
  • 0 (default)—Do not enable per RAM block preserve/duplication. You can determine which registers should be duplicated through assignment.
Level Two Title