1. Stratix® 10 Embedded Memory Overview
2. Stratix® 10 Embedded Memory Architecture and Features
3. Stratix® 10 Embedded Memory Design Considerations
4. Stratix® 10 Embedded Memory IP References
5. Stratix 10 Embedded Memory Design Example
6. Stratix® 10 Embedded Memory User Guide Archives
7. Document Revision History for the Stratix® 10 Embedded Memory User Guide
2.1. Byte Enable in Stratix® 10 Embedded Memory Blocks
2.2. Address Clock Enable Support
2.3. Asynchronous Clear and Synchronous Clear
2.4. Memory Blocks Error Correction Code (ECC) Support
2.5. Force-to-Zero
2.6. Coherent Read Memory
2.7. Freeze Logic
2.8. True Dual Port Dual Clock Emulator
2.9. 'X' Propagation Support in Simulation
2.10. Stratix® 10 Supported Embedded Memory IPs
2.11. Stratix® 10 Embedded Memory Clocking Modes
2.12. Stratix® 10 Embedded Memory Configurations
2.13. Initial Value of Read and Write Address Registers
3.1. Consider the Memory Block Selection
3.2. Consider the Concurrent Read Behavior
3.3. Read-During-Write (RDW)
3.4. Consider Power-Up State and Memory Initialization
3.5. Reduce Power Consumption
3.6. Avoid Providing Non-Deterministic Input
3.7. Avoid Changing Clock Signals and Other Control Signals Simultaneously
3.8. Including the Reset Release FPGA IP in Your Design
3.9. Resource and Timing Optimization Feature in MLAB Blocks
3.10. Consider the Memory Depth Setting
3.11. Consider Registering the Memory Output
4.1.1. Release Information for RAM and ROM IPs
4.1.2. RAM: 1-PORT FPGA IP Parameters
4.1.3. RAM: 2-PORT FPGA IP Parameters
4.1.4. RAM: 4-PORT FPGA IP Parameters
4.1.5. ROM: 1-PORT FPGA IP Parameters
4.1.6. ROM: 2-PORT FPGA IP Parameters
4.1.7. RAM and ROM Interface Signals
4.1.8. Changing Parameter Settings Manually
4.3.1. Release Information for FIFO FPGA IP
4.3.2. Configuration Methods
4.3.3. Specifications
4.3.4. FIFO Functional Timing Requirements
4.3.5. SCFIFO ALMOST_EMPTY Functional Timing
4.3.6. FIFO Output Status Flag and Latency
4.3.7. FIFO Metastability Protection and Related Options
4.3.8. FIFO Synchronous Clear and Asynchronous Clear Effect
4.3.9. SCFIFO and DCFIFO Show-Ahead Mode
4.3.10. Different Input and Output Width
4.3.11. DCFIFO Timing Constraint Setting
4.3.12. Coding Example for Manual Instantiation
4.3.13. Design Example
4.3.14. Gray-Code Counter Transfer at the Clock Domain Crossing
4.3.15. Guidelines for Embedded Memory ECC Feature
4.3.16. FIFO IP Parameters
4.3.17. Reset Scheme
4.1.8. Changing Parameter Settings Manually
When the IP has been generated using the IP Parameter Editor, you can use this flow to change of the parameter settings within the specified memory mode. However, to change the memory mode, use the IP Parameter Editor to configure and regenerate the IP.
Follow these steps to change the parameter settings manually:
- Locate the Verilog design file: <project directory>/<project name_software version>/synth/<projectName_coreName_QuartusVersion_random>.v.
- Change the parameter settings in the design file. Ensure that you use only legal parameter values as specified in Parameters and Signals topic. Failing to do so results in compilation errors.
- Compile the design using the Quartus® Prime software.
For example, the following codes enable the ECC feature and specify the initialization file.
altera_syncram_component.enable_ecc = "TRUE", altera_syncram_component.ecc_pipeline_stage_enabled = "FALSE", altera_syncram_component.init_file = "mif1.mif",
To disable the ECC feature and specify a different .mif file, make the following changes.
altera_syncram_component.enable_ecc = "FALSE", altera_syncram_component.ecc_pipeline_stage_enabled = "FALSE", altera_syncram_component.init_file = "mif2.mif",