Cyclone® V SoC Development Kit User Guide

Download PDF
ID 830285
Date 10/07/2024
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Getting Started 3. Development Kit Setup 4. Board Update Portal 5. Board Test System 6. Document Revision History for the Cyclone® V SoC Development Kit User Guide A. Development Kit Components B. Additional Information
1. Overview x
1.1. Block Diagram 1.2. Feature Summary 1.3. Box Contents
2. Getting Started x
2.1. Before You Begin 2.2. Inspecting the Boards 2.3. Software and Driver Installation
2.3. Software and Driver Installation x
2.3.1. Installing the Quartus® Prime Standard Edition Software 2.3.2. Installing the Intel® SoC EDS 2.3.3. Installing the Development Kit 2.3.4. Installing the Intel® FPGA Download Cable II Driver
3. Development Kit Setup x
3.1. Setting Up the Development Kit 3.2. Factory Default Switch and Jumper Settings 3.3. Restoring the MAX® V CPLD to the Factory Setting 3.4. Restoring CFI Flash Device to the Factory Defaults
3.2. Factory Default Switch and Jumper Settings x
3.2.1. Restoring the Default Settings for Power Solution 2 Board 3.2.2. Restoring the Default Settings for Power Solution 1 Board
4. Board Update Portal x
4.1. Connecting to the Board Update Portal Web Page
5. Board Test System x
5.1. Preparing the Board for the Board Test System 5.2. Running the Board Test System 5.3. Using the Board Test System 5.4. The Power Monitor 5.5. The Clock Control 5.6. Configuring the FPGA Using the Quartus® Prime Programmer
5.3. Using the Board Test System x
5.3.1. The Configure Menu 5.3.2. The System Info Tab 5.3.3. The GPIO Tab Character LCD User DIP Switches User LEDs Push Buttons 5.3.4. The I2C Tab 5.3.5. The DDR3 Tab 5.3.6. The SDI Video Tab 5.3.7. The HSMC Tab
5.6. Configuring the FPGA Using the Quartus® Prime Programmer x
5.6.1. Before Configuring 5.6.2. Configuring the FPGA
A. Development Kit Components x
A.1. Board Overview A.2. Programming Flash Memory A.3. Power
A.2. Programming Flash Memory x
A.2.1. CFI Flash Memory A.2.2. quad SPI Flash Memory A.2.3. SD Card Memory
A.2.1. CFI Flash Memory x
A.2.1.1. CFI Flash Memory Map A.2.1.2. Programming CFI Flash Using the Quartus® Prime Programmer A.2.1.3. Converting .sof Files to a .pof
A.2.2. quad SPI Flash Memory x
A.2.2.1. Programming quad SPI Flash Using the Quartus® Prime Programmer
A.2.3. SD Card Memory x
A.2.3.1. Programming the SD Card Boot Image
B. Additional Information x
B.1. Safety and Regulatory Information B.2. Compliance Information
B.1. Safety and Regulatory Information x
B.1.1. Safety Warnings B.1.2. Safety Cautions
1. Overview
2. Getting Started
3. Development Kit Setup
4. Board Update Portal
5. Board Test System
6. Document Revision History for the Cyclone® V SoC Development Kit User Guide
A. Development Kit Components
B. Additional Information

5.3.3. The GPIO Tab

The GPIO tab allows you to interact with all the general-purpose user I/O components on your board. You can write to the character LCD, read DIP switch settings, turn LEDs on or off, and detect push button presses.
Figure 10. The GPIO Tab

The following sections describe the controls on the GPIO tab.

Character LCD

The Character LCD controls allow you to display text strings on the character LCD on your board. Type text in the text boxes and then click Display.
Attention: If you exceed the 16 character display limit on either line, a warning message appears.

User DIP Switches

The read-only User DIP switches control displays the current positions of the switches in the user DIP switch bank. Change the switches on the board to see the graphical display change accordingly.

User LEDs

The User LEDs control displays the current state of the user LEDs. Click the graphical representation of the LEDs to turn the board LEDs on and off. You can click ALL to turn on and off all of the user LEDs at once.

Push Buttons

The read-only Push Buttons control displays the current state of the board user push buttons. Press a push button on the board to see the graphical display change accordingly

Level Two Title