Hard Processor System Component Reference Manual: Agilex™ 5 SoCs

Download PDF
ID 813752
Date 4/10/2025
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. Introduction to the Agilex™ 5 Hard Processor System Component 2. Configuring the Agilex™ 5 Hard Processor System Component 3. Simulating the Agilex™ 5 HPS Component 4. Simulating the Agilex™ 5 HPS bridges (H2F, LWH2F, and F2SDRAM) 5. Design Guidelines 6. Document Revision History for the Hard Processor System Component Reference Manual Agilex™ 5 SoCs
1. Introduction to the Agilex™ 5 Hard Processor System Component x
1.1. Release Notes 1.2. Micro Processor Unit 1.3. Application Processor Subsystem 1.4. Peripheral Subsystem 1.5. CoreSight* Debug Components 1.6. Interconnect 1.7. FPGA Bridges 1.8. Introduction to the Agilex™ 5 Hard Processor System Component Revision History
1.1. Release Notes x
1.1.1. HPS IP 7.0.0 1.1.2. HPS IP 6.0.0 1.1.3. HPS IP 5.1.0 1.1.4. HPS IP 4.0.0
2. Configuring the Agilex™ 5 Hard Processor System Component x
2.1. Parameterizing the HPS Component 2.2. HPS-FPGA Interfaces 2.3. SDRAM 2.4. HPS Clocks, Reset, Power 2.5. I/O Delays 2.6. Pin Mux and Peripherals 2.7. Generating and Compiling the HPS Component 2.8. Using the Address Span Extender Component 2.9. Configuring the Agilex™ 5 Hard Processor System Component Revision History
2.2. HPS-FPGA Interfaces x
2.2.1. General 2.2.2. HPS FPGA Bridges 2.2.3. DMA Controller Interface 2.2.4. Interrupts
2.2.1. General x
2.2.1.1. Enable MPU Standby and Event Signals 2.2.1.2. Enable General Purpose Signals 2.2.1.3. Enable Debug APB* Interface 2.2.1.4. Enable System Trace Macrocell (STM) Hardware Events 2.2.1.5. Enable SWJ-DP JTAG Interface 2.2.1.6. Enable FPGA Cross Trigger Interface 2.2.1.7. Enable AMBA* Trace Bus (ATB)
2.2.2. HPS FPGA Bridges x
2.2.2.1. FPGA to HPS Subordinate 2.2.2.2. FPGA to SDRAM Subordinate 2.2.2.3. HPS to FPGA Manager 2.2.2.4. Lightweight HPS to FPGA Manager
2.2.4. Interrupts x
2.2.4.1. FPGA-to-HPS 2.2.4.2. HPS-to-FPGA
2.3. SDRAM x
2.3.1. Configurations for HPS IP 2.3.2. Configurations for HPS EMIF IP 2.3.3. Graphical Connections of HPS to HPS-EMIF 2.3.4. Configuration when using ECC 2.3.5. Configuration of HPS EMIF Calibration Settings 2.3.6. Supported Memory Protocols Among Device Families 2.3.7. IO96 Bank and Lane Usage for HPS EMIF 2.3.8. Quartus Report of I/O Bank Usage 2.3.9. Debugging with the External Memory Interface Debug Toolkit
2.4. HPS Clocks, Reset, Power x
2.4.1. Input Clocks 2.4.2. PLL Clocks 2.4.3. Power and Resets
2.4.1. Input Clocks x
2.4.1.1. External Clocks 2.4.1.2. FPGA-to-HPS Clocks 2.4.1.3. Peripheral FPGA Clocks
2.4.2. PLL Clocks x
2.4.2.1. Main PLL Output 2.4.2.2. Peripheral PLL Output 2.4.2.3. MPU Clocks 2.4.2.4. NOC Clocks 2.4.2.5. Peripheral Clocks 2.4.2.6. HPS-to-FPGA User Clocks
2.4.3. Power and Resets x
2.4.3.1. Power Configurations 2.4.3.2. Reset Signals
2.6. Pin Mux and Peripherals x
2.6.1. Pin Mux GUI 2.6.2. EMAC PTP Interface 2.6.3. HPS I/O Open Drain 2.6.4. HPS I/O Locations
2.6.1. Pin Mux GUI x
2.6.1.1. Auto-Place IP 2.6.1.2. Advanced
2.6.1.1. Auto-Place IP x
2.6.1.1.1. Options for NAND, SDMMC, TRACE, TPIU, EMAC
2.6.1.1.1. Options for NAND, SDMMC, TRACE, TPIU, EMAC x
2.6.1.1.1.1. HPS IO Placement Priority
2.6.1.2. Advanced x
2.6.1.2.1. Advanced IP Placement 2.6.1.2.2. Advanced FPGA Placement
3. Simulating the Agilex™ 5 HPS Component x
3.1. Simulation Flows 3.2. Clock and Reset Interface 3.3. FPGA-to-HPS AXI* Subordinate Interface 3.4. FPGA-to-SDRAM AXI* Subordinate Interface 3.5. HPS-to-FPGA AXI* Manager Interface 3.6. Lightweight HPS-to-FPGA AXI* Manager Interface 3.7. Simulating the Agilex™ 5 HPS Component Revision History
3.1. Simulation Flows x
3.1.1. Setting Up the HPS Component for Simulation 3.1.2. Generating the HPS Simulation Model in Platform Designer 3.1.3. RTL Simulation Setup Scripts
3.1.3. RTL Simulation Setup Scripts x
3.1.3.1. QuestaSim* Simulation Steps 3.1.3.2. Cadence® Xcelium* Simulation Steps 3.1.3.3. Synopsys* VCS* MX Simulation Steps 3.1.3.4. Riviera-PRO* Simulation Steps 3.1.3.5. Synopsys* VCS* Simulation Steps 3.1.3.6. VSIM Command Line Aliases and Variables
3.2. Clock and Reset Interface x
3.2.1. Clock Interface 3.2.2. Reset Interface
4. Simulating the Agilex™ 5 HPS bridges (H2F, LWH2F, and F2SDRAM) x
4.1. Setting up the HPS Component for Simulation 4.2. Generating the HPS Simulation Model in Platform Designer 4.3. Editing the TestBench scripts 4.4. Running the TestBench scripts 4.5. Simulating the Agilex™ 5 HPS Bridges (H2F, LWH2F, and F2SRAM) Revision History
4.3. Editing the TestBench scripts x
4.3.1. my_simple_tb.sv 4.3.2. test_lwh2f.sv 4.3.3. test_h2f_128b.sv 4.3.4. test_f2sdram_256b.sv
4.4. Running the TestBench scripts x
4.4.1. Questa* Intel® FPGA Edition Simulation Steps
5. Design Guidelines x
5.1. HPS System Reset Considerations 5.2. Design Guidelines Revision History
1. Introduction to the Agilex™ 5 Hard Processor System Component
2. Configuring the Agilex™ 5 Hard Processor System Component
3. Simulating the Agilex™ 5 HPS Component
4. Simulating the Agilex™ 5 HPS bridges (H2F, LWH2F, and F2SDRAM)
5. Design Guidelines
6. Document Revision History for the Hard Processor System Component Reference Manual Agilex™ 5 SoCs

2.3.2. Configurations for HPS EMIF IP

The External Memory Interfaces for HPS IP contains the TOPOLOGY_GROUP. In this section, select the appropriate EMIF Technology Generation for your design.

Figure 11. EMIF IP Technology Generation
The EMIF Technology Generation drop-down can configure as:
  • ddr4 component
  • ddr5 component
  • lpddr4
  • lpddr5

Also in this section, select the appropriate HPS-EMIF Configuration for your design.

Figure 12. EMIF IP HPS-EMIF Configuration

You can configure the HPS-EMIF using the configuration drop-down:

  • 1x16 bit (uses one EMIF)
  • 1x32 bit (uses one EMIF)
  • 2x16 bit (uses one EMIF)
  • 2x32 bit (uses two EMIFs)
  • 4x16 bit (uses two EMIFs)
Level Two Title