Low Latency 40G Ethernet IP User Guide: Agilex™ 5 FPGAs and SoCs

Download PDF
ID 813652
Date 10/24/2025
Public
Document Table of Contents
Document Table of Contents x
1. About the Low Latency 40G Ethernet IP 2. Low Latency 40G Ethernet IP Parameters 3. Getting Started 4. Functional Description 5. Clocking and Reset Requirements 6. Interfaces and Signal Descriptions 7. Control, Status, and Statistics Register Descriptions 8. Comparison Between Various Low Latency 40G Ethernet IPs 9. Document Revision History for the Low Latency 40G Ethernet IP User Guide: Agilex™ 5 FPGAs and SoCs
1. About the Low Latency 40G Ethernet IP x
1.1. Low Latency 40G Ethernet IP Supported Features 1.2. Low Latency 40G Ethernet IP Device Family and Speed Grade Support 1.3. Resource Utilization 1.4. Release Information
1.2. Low Latency 40G Ethernet IP Device Family and Speed Grade Support x
1.2.1. Low Latency 40G Ethernet Device Family Support 1.2.2. Low Latency 40G Ethernet IP Device Speed Grade Support
3. Getting Started x
3.1. Introduction to Altera IP 3.2. Installing and Licensing IPs 3.3. Specifying the IP Parameters and Options 3.4. Simulating the IP 3.5. Generated File Structure 3.6. Integrating Your IP in Your Design 3.7. Testbench 3.8. Compiling the Full Design and Programming the FPGA
3.6. Integrating Your IP in Your Design x
3.6.1. Pin Assignments 3.6.2. Placement Settings
3.7. Testbench x
3.7.1. Understanding the Testbench Behavior
4. Functional Description x
4.1. Low Latency 40G Ethernet IP Functional Description 4.2. GTS Transceiver Configuration 4.3. Transmitter Datapath 4.4. Receiver Datapath 4.5. Flow Control 4.6. Link Fault Signaling Interface
4.3. Transmitter Datapath x
4.3.1. Transmitter MAC 4.3.2. Transmitter PCS 4.3.3. PMA
4.3.1. Transmitter MAC x
4.3.1.1. Preamble Insertion 4.3.1.2. Frame Padding 4.3.1.3. Inter-Packet Gap Generation and Insertion 4.3.1.4. Frame Check Sequence (CRC-32) Insertion 4.3.1.5. Transmitter Avalon® Streaming Filter
4.4. Receiver Datapath x
4.4.1. Receiver MAC 4.4.2. Receiver PCS
4.4.1. Receiver MAC x
4.4.1.1. IP Core Preamble Processing 4.4.1.2. IP Core CRC Checking and Dynamic Forwarding 4.4.1.3. IP Core Strict SFD Checking 4.4.1.4. Length/Type Field Processing
4.4.1.4. Length/Type Field Processing x
4.4.1.4.1. Frame Type Checking 4.4.1.4.2. Length Checking
4.5. Flow Control x
4.5.1. Transmitter Pause/PFC Flow Control Transmission 4.5.2. XON/XOFF Pause Frames
5. Clocking and Reset Requirements x
5.1. Clocks 5.2. Reset Requirements
6. Interfaces and Signal Descriptions x
6.1. Transmitter MAC Interface to User Logic 6.2. Receiver MAC Interface to User Logic 6.3. Transmitter PCS Interface to User Logic 6.4. Receiver PCS Interface to User Logic 6.5. GTS Transceivers Signals 6.6. GTS Transceiver Reconfiguration Signals 6.7. Avalon® Memory-Mapped Management Interface 6.8. Miscellaneous Status and Debug Signals 6.9. Reset Signals 6.10. Clocks 6.11. Flow Control Interface 6.12. GTS Reset Sequencer IP
7. Control, Status, and Statistics Register Descriptions x
7.1. PHY Registers 7.2. Transmitter MAC Registers 7.3. Receiver MAC Registers 7.4. Pause/PFC Flow Control 7.5. Statistics Counters 7.6. Shadow Register
1. About the Low Latency 40G Ethernet IP
2. Low Latency 40G Ethernet IP Parameters
3. Getting Started
4. Functional Description
5. Clocking and Reset Requirements
6. Interfaces and Signal Descriptions
7. Control, Status, and Statistics Register Descriptions
8. Comparison Between Various Low Latency 40G Ethernet IPs
9. Document Revision History for the Low Latency 40G Ethernet IP User Guide: Agilex™ 5 FPGAs and SoCs

4.4.2. Receiver PCS

In MAC, PCS and PMA variant, the receiver PCS module is an internal block and this block is connected to the internal receiver MAC block. Whereas in PCS and PMA variant, the MII data and control bus along with the other PCS control and status signals are provided as the user interface.

The receiver PCS interfaces with Hard PCS/PMA block is configured in 66:40 10G PCS Basic Generic Mode, with bit slip enabled and single data-rate. Each input stream thus carries an individual virtual lane for the 40G PCS. The PCS operates at 312.5 MHz. A read control/enable logic controls the incoming data throughput by reading the hard-PCS FIFOs only half of the cycles (66*4×312.5/2 = 41.250 Gbps).

The soft Receiver-PCS logically consists of five stages:
  • Word Lock: The word lock is achieved for each virtual lane/word-stream by utilizing the hard-PCS bit-slipping functionality (in the PCS gearbox). This is done through a soft control logic that sends the bit-slipping command and monitors incoming stream to declare when a corresponding lane is word-locked.
  • Merge: The four incoming streams/virtual-lanes from the hard-PCS are each 66-bit wide, that are read-in with a cadence that alternates inputting data from even/odd FIFOs at every clock cycle. The four input channels thus have twice the capability to required bandwidth. This redundant capability is not available at later stages that are two 66-bit words wide. The merge stage therefore translates those four input channels into two words by merging two physical/virtual lanes on to one.
  • Lane Reordering, De-skew and Lane Alignment: The locked virtual lanes are next de-skewed in receiver PCS and lanes are aligned together. This stage declares lane alignment lock status.
  • Descrambler: The aligned lanes are descrambled in this stage.
  • MII Decoding: MII data is decoded and two 64-bit words along with control signals are provided to the receiver MAC.
Level Two Title