Low Latency 40G Ethernet IP User Guide: Agilex™ 5 FPGAs and SoCs

Download PDF
ID 813652
Date 10/24/2025
Public
Document Table of Contents
Document Table of Contents x
1. About the Low Latency 40G Ethernet IP 2. Low Latency 40G Ethernet IP Parameters 3. Getting Started 4. Functional Description 5. Clocking and Reset Requirements 6. Interfaces and Signal Descriptions 7. Control, Status, and Statistics Register Descriptions 8. Comparison Between Various Low Latency 40G Ethernet IPs 9. Document Revision History for the Low Latency 40G Ethernet IP User Guide: Agilex™ 5 FPGAs and SoCs
1. About the Low Latency 40G Ethernet IP x
1.1. Low Latency 40G Ethernet IP Supported Features 1.2. Low Latency 40G Ethernet IP Device Family and Speed Grade Support 1.3. Resource Utilization 1.4. Release Information
1.2. Low Latency 40G Ethernet IP Device Family and Speed Grade Support x
1.2.1. Low Latency 40G Ethernet Device Family Support 1.2.2. Low Latency 40G Ethernet IP Device Speed Grade Support
3. Getting Started x
3.1. Introduction to Altera IP 3.2. Installing and Licensing IPs 3.3. Specifying the IP Parameters and Options 3.4. Simulating the IP 3.5. Generated File Structure 3.6. Integrating Your IP in Your Design 3.7. Testbench 3.8. Compiling the Full Design and Programming the FPGA
3.6. Integrating Your IP in Your Design x
3.6.1. Pin Assignments 3.6.2. Placement Settings
3.7. Testbench x
3.7.1. Understanding the Testbench Behavior
4. Functional Description x
4.1. Low Latency 40G Ethernet IP Functional Description 4.2. GTS Transceiver Configuration 4.3. Transmitter Datapath 4.4. Receiver Datapath 4.5. Flow Control 4.6. Link Fault Signaling Interface
4.3. Transmitter Datapath x
4.3.1. Transmitter MAC 4.3.2. Transmitter PCS 4.3.3. PMA
4.3.1. Transmitter MAC x
4.3.1.1. Preamble Insertion 4.3.1.2. Frame Padding 4.3.1.3. Inter-Packet Gap Generation and Insertion 4.3.1.4. Frame Check Sequence (CRC-32) Insertion 4.3.1.5. Transmitter Avalon® Streaming Filter
4.4. Receiver Datapath x
4.4.1. Receiver MAC 4.4.2. Receiver PCS
4.4.1. Receiver MAC x
4.4.1.1. IP Core Preamble Processing 4.4.1.2. IP Core CRC Checking and Dynamic Forwarding 4.4.1.3. IP Core Strict SFD Checking 4.4.1.4. Length/Type Field Processing
4.4.1.4. Length/Type Field Processing x
4.4.1.4.1. Frame Type Checking 4.4.1.4.2. Length Checking
4.5. Flow Control x
4.5.1. Transmitter Pause/PFC Flow Control Transmission 4.5.2. XON/XOFF Pause Frames
5. Clocking and Reset Requirements x
5.1. Clocks 5.2. Reset Requirements
6. Interfaces and Signal Descriptions x
6.1. Transmitter MAC Interface to User Logic 6.2. Receiver MAC Interface to User Logic 6.3. Transmitter PCS Interface to User Logic 6.4. Receiver PCS Interface to User Logic 6.5. GTS Transceivers Signals 6.6. GTS Transceiver Reconfiguration Signals 6.7. Avalon® Memory-Mapped Management Interface 6.8. Miscellaneous Status and Debug Signals 6.9. Reset Signals 6.10. Clocks 6.11. Flow Control Interface 6.12. GTS Reset Sequencer IP
7. Control, Status, and Statistics Register Descriptions x
7.1. PHY Registers 7.2. Transmitter MAC Registers 7.3. Receiver MAC Registers 7.4. Pause/PFC Flow Control 7.5. Statistics Counters 7.6. Shadow Register
1. About the Low Latency 40G Ethernet IP
2. Low Latency 40G Ethernet IP Parameters
3. Getting Started
4. Functional Description
5. Clocking and Reset Requirements
6. Interfaces and Signal Descriptions
7. Control, Status, and Statistics Register Descriptions
8. Comparison Between Various Low Latency 40G Ethernet IPs
9. Document Revision History for the Low Latency 40G Ethernet IP User Guide: Agilex™ 5 FPGAs and SoCs

6.8. Miscellaneous Status and Debug Signals

These signals are asynchronous.
Table 21.   Miscellaneous Status and Debug Signals

Signal

Direction

Width

Description
tx_lanes_stable Output 1 Asserted when all transmitter lanes are stable and ready to transmit data.
rx_block_lock Output 1 Asserted when all lanes have identified 66-bit block boundaries in the serial data stream.
rx_am_lock Output 1 Asserted when all lanes have identified alignment markers in the data stream.
rx_pcs_ready Output 1 Asserted when the receiver lanes are fully aligned and ready to receive data.
i_system_pll_lock Input 1 Indicates that Sys PLL is locked.
local_fault_status Output 1 Asserted when the receiver MAC detects a local fault. This signal is available only if you turn on Enable link fault generation in the parameter editor.
remote_fault_status Output 1 Asserted when the receiver MAC detects a remote fault. This signal is available only if you turn on Enable link fault generation in the parameter editor.
tx_pll_locked Output 1 Enabled in PCS and PMA mode. Indicates that the Transmit PMA PLL is locked.
rx_hi_ber Output 1 Asserted to indicate the receiver PCS is in a high BER state.
rx_cdr_lock Output 1 Indicates the recovered clocks are locked to data.
Level Two Title