F-Tile Low Latency 100G Ethernet Intel® FPGA IP User Guide

Download PDF
ID 792946
Date 3/31/2025
Public
Document Table of Contents
Document Table of Contents x
1. About the F-Tile Low Latency 100G Ethernet Intel® FPGA IP User Guide 2. About this IP 3. Getting Started 4. F-Tile Low Latency 100G Ethernet Intel® FPGA IP Parameters 5. Functional Description 6. Reset 7. Interfaces and Signal Descriptions 8. Control, Status, and Statistics Register Descriptions 9. Document Revision History for the F-Tile Low Latency 100G Ethernet Intel® FPGA IP User Guide
2. About this IP x
2.1. Release Information 2.2. Features 2.3. Device Family Support
3. Getting Started x
3.1. Installing and Licensing Intel FPGA IP Cores 3.2. Specifying the IP Core Parameters and Options 3.3. Simulating the IP Core 3.4. Generated File Structure 3.5. Integrating Your IP Core in Your Design 3.6. Compiling the Full Design and Programming the FPGA
3.1. Installing and Licensing Intel FPGA IP Cores x
3.1.1. Intel FPGA IP Evaluation Mode
3.5. Integrating Your IP Core in Your Design x
3.5.1. Pin Assignments 3.5.2. Adding the F-Tile Reference and System PLL Clocks Intel FPGA IP 3.5.3. Placement Settings for the 100G Ethernet Intel FPGA IP Core
4. F-Tile Low Latency 100G Ethernet Intel® FPGA IP Parameters x
4.1. Main Tab Options 4.2. Analog Parameter Tab Options
5. Functional Description x
5.1. F-Tile Low Latency 100G Ethernet Intel® FPGA IP Functional Description 5.2. User Interface to Ethernet Transmission
5.1. F-Tile Low Latency 100G Ethernet Intel® FPGA IP Functional Description x
5.1.1. F-Tile Low Latency 100G Ethernet Intel® FPGA IP TX MAC Datapath 5.1.2. 100 GbE TX PCS 5.1.3. F-Tile Low Latency 100G Ethernet Intel® FPGA IP Core RX MAC Datapath 5.1.4. Link Fault Signaling Interface 5.1.5. 100 GbE RX PCS 5.1.6. Flow Control
5.1.1. F-Tile Low Latency 100G Ethernet Intel® FPGA IP TX MAC Datapath x
5.1.1.1. Frame Padding 5.1.1.2. Preamble Insertion 5.1.1.3. Inter-Packet Gap Generation and Insertion 5.1.1.4. Frame Check Sequence (CRC32) Insertion
5.1.3. F-Tile Low Latency 100G Ethernet Intel® FPGA IP Core RX MAC Datapath x
5.1.3.1. IP Core Preamble Processing 5.1.3.2. IP Core Malformed Packet Handling 5.1.3.3. Length/Type Field Processing
5.1.3.3. Length/Type Field Processing x
5.1.3.3.1. Length Checking 5.1.3.3.2. RX CRC Checking and Dynamic Forwarding
5.1.6. Flow Control x
5.1.6.1. TX Pause/PFC Flow Control Frame Transmission Request 5.1.6.2. XON/XOFF Pause Frames
5.2. User Interface to Ethernet Transmission x
5.2.1. Order of Transmission 5.2.2. Bit Order For TX and RX Datapaths
7. Interfaces and Signal Descriptions x
7.1. TX MAC Interface to User Logic 7.2. RX MAC Interface to User Logic 7.3. Transceivers 7.4. Transceiver Reconfiguration Signals 7.5. Avalon Memory-Mapped Management Interface 7.6. Miscellaneous Status and Debug Signals 7.7. Flow Control Signals 7.8. Clock Signals 7.9. Reset Signals
8. Control, Status, and Statistics Register Descriptions x
8.1. TX MAC Registers 8.2. RX MAC Registers 8.3. Pause/PFC Flow Control Registers 8.4. Statistics Registers 8.5. Hard IP Registers
8.4. Statistics Registers x
8.4.1. Statistics Registers
1. About the F-Tile Low Latency 100G Ethernet Intel® FPGA IP User Guide
2. About this IP
3. Getting Started
4. F-Tile Low Latency 100G Ethernet Intel® FPGA IP Parameters
5. Functional Description
6. Reset
7. Interfaces and Signal Descriptions
8. Control, Status, and Statistics Register Descriptions
9. Document Revision History for the F-Tile Low Latency 100G Ethernet Intel® FPGA IP User Guide

2.2. Features

This IP core is designed to the 25G & 50G Ethernet Specification, Draft 1.6 from the 25 Gigabit Ethernet Consortium and designed to the IEEE 802.3by 25Gb Ethernet specification, as well as the IEEE 802.3ba-2012 High Speed Ethernet Standard available on the IEEE website (www.ieee.org). The MAC provides RX cut-through frame processing to optimize latency. The IP supports the following features:

  • PHY features:
    • IEEE 802.3-2018 Ethernet Standard Clause 107 for 25GBASE-R.
    • IEEE 802.3-2018 Ethernet Standard Clause 109 elective physical medium attachment (PMA) for interface to 25GBASE-SR optical PMD transceiver.
  • Frame structure control features:
    • Support for jumbo packets, defined as packets greater than 1500 bytes.
    • Receive (RX) CRC removal and pass-through control.
    • Transmit (TX) CRC generation and insertion.
    • RX and TX preamble pass-through option for applications that require proprietary user management information transfer.
    • TX automatic frame padding to meet the 64-byte minimum Ethernet frame length.
  • Frame monitoring and statistics:
    • RX CRC checking and error reporting.
    • RX malformed packet checking per IEEE specification.
    • Optional statistics counters.
    • Optional fault signaling detects and reports local fault and generates remote fault, with IEEE 802.3ba-2012 Ethernet Standard Clause 46 support.
    • Unidirectional transport as defined in Clause 66 of the IEEE 802.3-2012 Ethernet Standard.
  • Flow control:
    • Standard IEEE 802.3 Clause 31 and Priority-Based IEEE 802.1Qbb flow control.
  • Debug and testability features:
    • Programmable serial PMA local loopback (TX to RX) at the serial transceiver for self-diagnostic testing.
    • TX error insertion capability.
  • User system interfaces:
    • Avalon® memory-mapped management interface to access the IP control and status registers.
    • Avalon® streaming data path interface connects to client logic.
    • Configurable ready latency of 0 or 3 clock cycles for Avalon® streaming TX interface.
    • Hardware and software reset control.

For a detailed specification of the Ethernet protocol refer to the IEEE 802.3 Ethernet Standard.

Related Information
Level Two Title