Agilex™ 7 Embedded Memory User Guide

Download PDF
ID 683241
Date 4/15/2025
Public

Visible to Intel only — GUID: vgo1459220410722

Ixiasoft

View Details

Document Table of Contents
Document Table of Contents x
1. Agilex™ 7 Embedded Memory Overview 2. Agilex™ 7 Embedded Memory Architecture and Features 3. Agilex™ 7 Embedded Memory Design Considerations 4. Agilex™ 7 Embedded Memory IP References 5. Agilex™ 7 Embedded Memory Debugging 6. Agilex™ 7 Embedded Memory User Guide Archives 7. Document Revision History for the Agilex™ 7 Embedded Memory User Guide
1. Agilex™ 7 Embedded Memory Overview x
1.1. Agilex™ 7 Embedded Memory Features
2. Agilex™ 7 Embedded Memory Architecture and Features x
2.1. Fabric Network-On-Chip (NoC) in Agilex™ 7 M-Series M20K Blocks 2.2. Byte Enable in Agilex™ 7 Embedded Memory Blocks 2.3. Address Clock Enable Support 2.4. Asynchronous Clear and Synchronous Clear 2.5. Memory Blocks Error Correction Code (ECC) Support 2.6. Agilex™ 7 Embedded Memory Clocking Modes 2.7. Agilex™ 7 Embedded Memory Configurations 2.8. Force-to-Zero 2.9. Coherent Read Memory 2.10. Freeze Logic 2.11. True Dual Port Dual Clock Emulator 2.12. Initial Value of Read and Write Address Registers 2.13. Timing/Power Optimization Feature in M20K Blocks 2.14. Agilex™ 7 Supported Embedded Memory IPs
2.2. Byte Enable in Agilex™ 7 Embedded Memory Blocks x
2.2.1. Byte Enable Controls 2.2.2. Data Byte Output 2.2.3. Byte Enable Behavior
2.5. Memory Blocks Error Correction Code (ECC) Support x
2.5.1. Error Correction Code Truth Table 2.5.2. Parity Bit 2.5.3. ECC Parity Flip 2.5.4. ECC Read-During-Write Behavior
2.6. Agilex™ 7 Embedded Memory Clocking Modes x
2.6.1. Single Clock Mode 2.6.2. Read/Write Clock Mode 2.6.3. Input/Output Clock Mode 2.6.4. Asynchronous/Synchronous Clears in Clocking Modes 2.6.5. Output Read Data in Simultaneous Read/Write 2.6.6. Independent Clock Enables in Clocking Modes
2.7. Agilex™ 7 Embedded Memory Configurations x
2.7.1. Mixed-Width Port Configurations
2.9. Coherent Read Memory x
2.9.1. Forwarding Logic
3. Agilex™ 7 Embedded Memory Design Considerations x
3.1. Consider the Memory Block Selection 3.2. Consider the Concurrent Read Behavior 3.3. Read-During-Write (RDW) 3.4. Consider Power-Up State and Memory Initialization 3.5. Reduce Power Consumption 3.6. Avoid Providing Non-Deterministic Input 3.7. Avoid Changing Clock Signals and Other Control Signals Simultaneously 3.8. Advanced Settings in Quartus® Prime Software for Memory 3.9. Consider the Memory Depth Setting 3.10. M20K Embedded Memory Block Input Clock Quality Requirement 3.11. Consider Registering the Memory Output
3.3. Read-During-Write (RDW) x
3.3.1. Customize Read-During-Write Behavior
3.3.1. Customize Read-During-Write Behavior x
3.3.1.1. Same-Port Read-During-Write Mode 3.3.1.2. Mixed-Port Read-During-Write Mode
4. Agilex™ 7 Embedded Memory IP References x
4.1. On-Chip Memory RAM and ROM FPGA IPs 4.2. eSRAM Agilex™ FPGA IP 4.3. FIFO Intel FPGA IP 4.4. Shift Register (RAM-based) FPGA IP
4.1. On-Chip Memory RAM and ROM FPGA IPs x
4.1.1. Release Information for RAM and ROM IPs 4.1.2. RAM: 1-PORT FPGA IP Parameters 4.1.3. RAM: 2-PORT FPGA IP Parameters 4.1.4. RAM: 4-PORT FPGA IP Parameters 4.1.5. ROM: 1-PORT FPGA IP Parameters 4.1.6. ROM: 2-PORT FPGA IP Parameters 4.1.7. Changing Parameter Settings Manually 4.1.8. RAM and ROM Interface Signals
4.1.7. Changing Parameter Settings Manually x
4.1.7.1. RAM and ROM Parameter Settings
4.2. eSRAM Agilex™ FPGA IP x
4.2.1. Release Information for eSRAM Agilex™ FPGA IP 4.2.2. eSRAM System Features 4.2.3. eSRAM Agilex™ FPGA IP Parameters 4.2.4. eSRAM Agilex™ FPGA IP Interface Signals 4.2.5. eSRAM Timing Diagrams
4.2.2. eSRAM System Features x
4.2.2.1. eSRAM Specifications
4.3. FIFO Intel FPGA IP x
4.3.1. Release Information for FIFO Intel FPGA IP 4.3.2. Configuration Methods 4.3.3. Specifications 4.3.4. FIFO Functional Timing Requirements 4.3.5. SCFIFO ALMOST_EMPTY Functional Timing 4.3.6. FIFO Output Status Flag and Latency 4.3.7. FIFO Metastability Protection and Related Options 4.3.8. FIFO Synchronous Clear and Asynchronous Clear Effect 4.3.9. SCFIFO and DCFIFO Show-Ahead Mode 4.3.10. Different Input and Output Width 4.3.11. DCFIFO Timing Constraint Setting 4.3.12. Coding Example for Manual Instantiation 4.3.13. Gray-Code Counter Transfer at the Clock Domain Crossing 4.3.14. Guidelines for Embedded Memory ECC Feature 4.3.15. FIFO Intel FPGA IP Parameters 4.3.16. Reset Scheme
4.3.3. Specifications x
4.3.3.1. Verilog HDL Prototype 4.3.3.2. VHDL Component Declaration 4.3.3.3. VHDL LIBRARY-USE Declaration 4.3.3.4. HDL Code from Parameterizable Macros Template 4.3.3.5. FIFO Signals 4.3.3.6. FIFO Parameter Settings
4.3.8. FIFO Synchronous Clear and Asynchronous Clear Effect x
4.3.8.1. Recovery and Removal Timing Violation Warnings when Compiling a DCFIFO
4.3.11. DCFIFO Timing Constraint Setting x
4.3.11.1. Embedded Timing Constraint 4.3.11.2. User Configurable Timing Constraint
4.3.11.2. User Configurable Timing Constraint x
4.3.11.2.1. SDC Commands
4.4. Shift Register (RAM-based) FPGA IP x
4.4.1. Release Information for Shift Register (RAM-based) FPGA IP 4.4.2. Shift Register (RAM-based) FPGA IP 4.4.3. Shift Register (RAM-based) FPGA IP General Description 4.4.4. Shift Register (RAM-based) FPGA IP Parameter Settings 4.4.5. Shift Register Ports and Parameters Setting
1. Agilex™ 7 Embedded Memory Overview
2. Agilex™ 7 Embedded Memory Architecture and Features
3. Agilex™ 7 Embedded Memory Design Considerations
4. Agilex™ 7 Embedded Memory IP References
5. Agilex™ 7 Embedded Memory Debugging
6. Agilex™ 7 Embedded Memory User Guide Archives
7. Document Revision History for the Agilex™ 7 Embedded Memory User Guide

4.1.2. RAM: 1-PORT FPGA IP Parameters

Table 24.   RAM: 1-PORT FPGA IP Parameters—Widths/Blk Type/Clks Tab
Parameter Allowed Values Description
How wide should the ‘q’ output bus be? — Specifies the width of the ‘q’ output bus.
How many words of memory? — Specifies the number of bit words.
What should the memory block type be?
  • Auto
  • MLAB
  • M20K
  • LCs
Specifies the memory block type. The types of memory block that are available for selection depends on your target device.
Set the maximum block depth to
  • Auto: Auto, 32, 64, 128, 256, 512, 1024, 2048, or 4096
  • MLAB: Auto or 32
  • M20K: Auto, 512, 1024, or 2048
  • LCs: Auto
Specifies the maximum block depth in words.
How should the memory be implemented? Use default logic cell style

Specifies the logic cell implementation method.

Select Use default logic cell style if you prefer smaller and faster memory capacity.

Which clocking method would you like to use?
  • Single clock
  • Dual clock: use separate ‘input’ and ‘output’ clocks
Specifies the clocking method to use.
  • Single clock—a single clock and a clock enable controls all registers of the memory block.
  • Dual clock: use separate ‘input’ and ‘output’ clocks—an input clock controls all registers related to the data input to the embedded memory block including data, address, byte enables, read enables, and write enables. An output clock controls the data output registers.
Table 25.   RAM: 1-PORT FPGA IP Parameters—Regs/Clken/Byte Enable/Aclrs Tab
Parameter Allowed Values Description
Which ports should be registered? ‘data’ and ‘wren’ input ports On/Off Specifies whether to register the input and output ports.
‘address’ input port
‘q’ output port
Create one clock enable signal for each clock signal On/Off Specifies whether to turn on the option to create one clock enable signal for each clock signal.
Note: All registered ports are controlled by the enable signal(s).
Use clock enable for port A input registers On/Off Specifies whether to use clock enable for port A input registers.
Use clock enable for port A output registers On/Off Specifies whether to use clock enable for port A output registers.
Create an ‘addressstall_a’ input port. On/Off Specifies whether to create an addressstall_a input port. You can create this port to act as an extra active low clock enable input for the address registers.
Create byte enable for port A On/Off Specifies whether to create a byte enable for port A. Turn on this option if you want to mask the input data so that only specific bytes, nibbles, or bits of data are written.

To enable byte enable for port A and port B, the data width ratio has to be 1 or 2 for the RAM: 1-PORT and RAM: 2-PORT IPs.

What is the width of a byte for byte enables?
  • MLAB: 5 or 10
  • M20K: 8, 9, or 10
Specifies the byte width of the byte enable port. The width of the data input port must be divisible by the byte size.
Which registered ports should be affected by the 'aclr' port? 'q' port On/Off Specifies whether the registered ports are affected by an asynchronous clear port.
Which registered ports should be affected by the 'sclr' port? 'q' port On/Off Specifies whether the registered ports are affected by a synchronous clear port.
Create a 'rden' read enable signal On/Off Turn on if you want to create a read enable signal.
Table 26.   RAM: 1-PORT FPGA IP Parameters—Read During Write Option Tab
Parameter Allowed Values Description
What should the ‘q’ output be when reading from a memory location being written to?
  • Don’t Care
  • Old Data
Specifies the output behavior when read-during-write occurs.

Don’t Care—The RAM outputs “don't care” or “unknown” values for read-during-write operation.

Old Data—The RAM outputs reflect the old data at that address before the write operation proceeds.

Get x's for write masked bytes instead of old data when byte enable is used On/Off Turn on this option to obtain ‘X’ on the masked byte.
Table 27.   RAM: 1-PORT FPGA IP Parameters—Mem Init Tab
Parameter Allowed Values Description
Do you want to specify the initial content of the memory?
  • No, leave it blank
  • Yes, use this file for the memory content data
Specifies the initial content of the memory.

To initialize the memory to zero, select No, leave it blank.

To use a memory initialization file (.mif) or a hexadecimal (Altera-format) file (.hex), select Yes, use this file for the memory content data.

Initialize memory content data to XX..X on power-up in simulation On/Off Specifies whether to initialize memory content data to XX..X on power-up in simulation. Memory must be blank to turn on this option.
File name — Specify a file name if initial content of the memory is not set to blank. The file must be in .hex or .mif format.
Implement clock-enable circuitry for use in a partial reconfiguration region On/Off Specifies whether to implement clock-enable circuitry for use in a partial reconfiguration region.
Table 28.   RAM: 1-PORT FPGA IP Parameters—Performance Optimization Tab
Parameter Allowed Values Description
Enable Force To Zero On/Off Specifies whether to set the output to zero when you deassert the read enable signal.

Enabling this feature helps improve the glue logic performance when the selected memory depth is larger than a single memory block.

Which timing/power optimization option do you want to use?
  • Auto
  • High Speed 8
  • Low Power
Specifies the timing/power optimization option to use. This option is only applicable when you select M20K memory type on Agilex™ 7 devices.
8 For Agilex™ 7 M-Series, only HIGH_SPEED option is available.
Level Two Title