Symmetric Cryptographic Accelerator Hard IP User Guide

Download PDF
ID 714305
Date 11/28/2025
Public
Document Table of Contents
Document Table of Contents x
1. Introduction 2. Interface Overview 3. Parameters 4. Designing with the IP 5. Block Description 6. Cryptographic IP Data Profiles 7. Configuration Registers 8. Design Example 9. Document Revision History for the Symmetric Cryptographic Accelerator Hard IP User Guide
1. Introduction x
1.1. Terminology 1.2. IP Overview 1.3. Release Information 1.4. Device Family Support 1.5. Resource Utilization
1.2. IP Overview x
1.2.1. IP Applications
2. Interface Overview x
2.1. Clock Signals 2.2. Reset Signals 2.3. AXI-ST Interface 2.4. AXI-Lite Interface
4. Designing with the IP x
4.1. Installing and Licensing IP Cores 4.2. Specifying the IP Parameters and Options 4.3. Generated File Structure 4.4. Symmetric Cryptographic Accelerator Hard IP Flow 4.5. Dynamically Disabling the SM4 Capability 4.6. Error Handling 4.7. Error Reporting 4.8. Resetting the IP 4.9. Channel Definition and Allocation 4.10. Byte Ordering 4.11. AXI-ST Single Packet Mode 4.12. AXI-ST Multiple Packet Mode
4.1. Installing and Licensing IP Cores x
4.1.1. IP Evaluation Mode
4.6. Error Handling x
4.6.1. Steps to Record and Report the Received Errors to the Soft Logic 4.6.2. Detected Error Handling 4.6.3. Key RAM ECC Error Handling
4.6.2. Detected Error Handling x
4.6.2.1. Recovering from a Recoverable Error 4.6.2.2. Recovering from an Internal Error
5. Block Description x
5.1. Reset Sequencer 5.2. AXI-ST Ready Latency 5.3. AXI Adapter 5.4. Integrity Check Value Comparison 5.5. GCM Padding and Depadding
5.3. AXI Adapter x
5.3.1. MAC Packing 5.3.2. Data Last Indicator 5.3.3. Stream and Channel ID Buffering 5.3.4. TKEEP and LAST_SEGMENT Signals Generation 5.3.5. MAC Dropping on Decryption
5.5. GCM Padding and Depadding x
5.5.1. GCM Padding 5.5.2. GCM Depadding
6. Cryptographic IP Data Profiles x
6.1. MAC Security Profile (MACsec) 6.2. IP Security Profile (IPsec) 6.3. Generic GCM Profile (GCM) 6.4. Generic XTS Profile (XTS)
6.1. MAC Security Profile (MACsec) x
6.1.1. MACsec Flow 6.1.2. AXI-ST Interface Using MAC Security (MACsec) Profile Pattern
6.2. IP Security Profile (IPsec) x
6.2.1. AXI-ST Interface Using IP Security (IPsec) Profile Pattern
6.3. Generic GCM Profile (GCM) x
6.3.1. AXI- ST Interface Using Generic GCM Profile Pattern
6.4. Generic XTS Profile (XTS) x
6.4.1. AXI-ST Interface Using Generic XTS Profile Pattern
8. Design Example x
8.1. Functional Description 8.2. Crypto VSIP Top Block Descriptions 8.3. Test Configurations 8.4. Software Requirements 8.5. Simulation Requirements 8.6. Steps to Generate the Design Example 8.7. Running Simulation Tests 8.8. Running Hardware Tests
8.2. Crypto VSIP Top Block Descriptions x
8.2.1. Clock and Reset 8.2.2. Host Interface
8.7. Running Simulation Tests x
8.7.1. Steps to Simulate the Design Example
8.8. Running Hardware Tests x
8.8.1. Supported Boards 8.8.2. Steps to Compile the Design Example for Hardware 8.8.3. Steps to Run the Design Example on Hardware
1. Introduction
2. Interface Overview
3. Parameters
4. Designing with the IP
5. Block Description
6. Cryptographic IP Data Profiles
7. Configuration Registers
8. Design Example
9. Document Revision History for the Symmetric Cryptographic Accelerator Hard IP User Guide

4.6.2.1. Recovering from a Recoverable Error

Follow these steps to recover from a recoverable error:

  1. Read the error log on the AXI-Lite interface by reading the ferr_log, pacer_log1, and pacer_log2 registers.
  2. Clear the error log by writing clear on the registers in 1.
  3. Understand and correct the cause of the error.
  4. Assert the tuser.error_clear signal using the profile ID where the error occurred. This step clears the specified profile of the errors.
Level Two Title