Intel® Stratix® 10 Configuration via Protocol (CvP) Implementation User Guide

Download PDF
ID 683704
Date 9/26/2022
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. Overview 2. CvP Description 3. CvP Topologies 4. Design Considerations 5. CvP Driver and Registers 6. Understanding the Design Steps for CvP Initialization and Update Mode in Intel® Stratix® 10 7. Intel® Stratix® 10 Configuration via Protocol (CvP) Implementation User Guide Archives 8. Document Revision History
1. Overview x
1.1. Benefits of Using CvP 1.2. CvP System 1.3. CvP Modes
1.3. CvP Modes x
1.3.1. CvP Limitations and Restrictions
1.3.1. CvP Limitations and Restrictions x
1.3.1.1. CvP Error Recovery
2. CvP Description x
2.1. Configuration Images 2.2. CvP Modes 2.3. Compression Features 2.4. Pin Description
2.2. CvP Modes x
2.2.1. CvP Initialization Mode 2.2.2. CvP Update Mode
3. CvP Topologies x
3.1. Single Endpoint 3.2. Multiple Endpoints
4. Design Considerations x
4.1. Designing CvP for an Open System 4.2. Designing CvP for a Closed System
4.1. Designing CvP for an Open System x
4.1.1. FPGA Power Supplies Ramp Time Requirement 4.1.2. PCIe* Wake-Up Time Requirement
4.1.2. PCIe* Wake-Up Time Requirement x
4.1.2.1. For CvP Initialization Mode 4.1.2.2. For CvP Update Mode
5. CvP Driver and Registers x
5.1. CvP Driver Support 5.2. CvP Driver Flow 5.3. VSEC Registers for CvP
5.3. VSEC Registers for CvP x
5.3.1. Vendor Specific Capability Header Register 5.3.2. Vendor Specific Header Register 5.3.3. Intel Marker Register 5.3.4. User Configurable Device/Board ID Register 5.3.5. CvP Status Register 5.3.6. CvP Mode Control Register 5.3.7. CvP Data Registers 5.3.8. CvP Programming Control Register 5.3.9. CvP Credit Register
6. Understanding the Design Steps for CvP Initialization and Update Mode in Intel® Stratix® 10 x
6.1. Implementation of CvP Initialization Mode 6.2. Implementation of CvP Update Mode
6.1. Implementation of CvP Initialization Mode x
6.1.1. Generating the Synthesis HDL files for Avalon® -ST Intel® Stratix® 10 Hard IP for PCI Express 6.1.2. Setting up the CvP Parameters in Device and Pin Options 6.1.3. Compiling the Design 6.1.4. Converting the SOF File 6.1.5. Bringing up the Hardware
6.1.5. Bringing up the Hardware x
6.1.5.1. Installing the Upstream Open Source CvP Driver in Linux Systems 6.1.5.2. Modifying MSEL/DIP switch on Intel® Stratix® 10 FPGA Development Kit 6.1.5.3. Programming CvP Images
6.2. Implementation of CvP Update Mode x
6.2.1. Instantiating the PCIe* Hard IP 6.2.2. Setting Up the CvP Parameters 6.2.3. Setting up the Base Revision 6.2.4. Setting up and Compile the Updated Revision 6.2.5. Converting the SOF file of the Updated Revision 6.2.6. Programming the Core RBF file from the Updated Revision via PCIe Link
6.2.3. Setting up the Base Revision x
6.2.3.1. Creating a Reserved Core Partition 6.2.3.2. Defining a Logic Lock Region 6.2.3.3. Compiling and Exporting the Root Partition
1. Overview
2. CvP Description
3. CvP Topologies
4. Design Considerations
5. CvP Driver and Registers
6. Understanding the Design Steps for CvP Initialization and Update Mode in Intel® Stratix® 10
7. Intel® Stratix® 10 Configuration via Protocol (CvP) Implementation User Guide Archives
8. Document Revision History

5.3.6. CvP Mode Control Register

Table 11.  CvP Mode Control Register (Byte Offset: 0xBA0)
Bits Name Reset Value Access Description
[31:3] — 0x0000 RO Reserved.
[2] — 0x0000 RW Reserved3.
[1] PLD_DISABLE 1'b0 RW/RO Enables/disables the PLD interface. This allows Host driver to switch the PLD interface out before USER MODE deasserts, and to switch the PLD interface back in only after USER MODE has been asserted. This helps to prevent any glitches or race conditions during the USER MODE switching.
  • 1: Disable the application layer interface.
  • 0: Enable the application layer interface.
Only change the value of this signal when there has been no other TLP’s to or from the HIP for 10 us. There should be no TLP’s issued to the HIP for 10 us after this value changes. When entering CVP, this bit should be set before CVP_MODE is set. When exiting CVP, it should be cleared after CVP_MODE is clears. This ensures that there is no PLD switching during CVP. This field is RW when cvp_en=1, and RO when cvp_en=0.
[0] CVP_MODE 1'b0 RW Controls whether the Hard IP for PCI Express is in CVP_MODE or normal mode.
  • 1: CVP_MODE is active. Signals to the SDM active and all TLPs are route to the Configuration Space. This CVP_MODE cannot be enabled if CVP_EN = 0.
  • 0: The IP core is in normal mode and TLPs are route to the FPGA fabric.
3 Intel® recommends to set the reserved bit to 0 for write operation. For read operations, the PCIe* IP always generates 0 as the output.
Level Two Title