L-Tile and H-Tile Avalon® Memory-mapped Intel® FPGA IP for PCI Express* User Guide

Download PDF
ID 683667
Date 9/13/2024
Public
Document Table of Contents
Document Table of Contents x
1. Introduction 2. Quick Start Guide 3. Interface Overview 4. Parameters 5. Designing with the IP Core 6. Block Descriptions 7. Registers 8. Programming Model for the DMA Descriptor Controller 9. Programming Model for the Avalon® -MM Root Port 10. Avalon-MM Testbench and Design Example 11. Document Revision History A. PCI Express Core Architecture B. Root Port Enumeration C. Troubleshooting and Observing the Link Status
1. Introduction x
1.1. Avalon-MM Interface for PCIe 1.2. Features 1.3. Release Information 1.4. Device Family Support 1.5. Recommended Fabric Speed Grades 1.6. Performance and Resource Utilization 1.7. Transceiver Tiles 1.8. PCI Express IP Core Package Layout 1.9. Channel Availability
2. Quick Start Guide x
2.1. Design Components 2.2. Hardware and Software Requirements 2.3. Directory Structure 2.4. Generating the Design Example 2.5. Simulating the Design Example 2.6. Compiling the Design Example and Programming the Device 2.7. Installing the Linux Kernel Driver 2.8. Running the Design Example Application
3. Interface Overview x
3.1. Avalon-MM DMA Interfaces when Descriptor Controller Is Internally Instantiated 3.2. Avalon-MM DMA Interfaces when Descriptor Controller is Externally Instantiated 3.3. Other Avalon-MM Interfaces 3.4. Clocks and Reset 3.5. System Interfaces
3.3. Other Avalon-MM Interfaces x
3.3.1. Avalon-MM Master Interfaces 3.3.2. Avalon-MM Slave Interfaces 3.3.3. Control Register Access (CRA) Avalon-MM Slave
4. Parameters x
4.1. Avalon-MM Settings 4.2. Base Address Registers 4.3. Device Identification Registers 4.4. PCI Express and PCI Capabilities Parameters 4.5. Configuration, Debug and Extension Options 4.6. PHY Characteristics 4.7. Example Designs
4.4. PCI Express and PCI Capabilities Parameters x
4.4.1. Device Capabilities 4.4.2. Link Capabilities 4.4.3. MSI and MSI-X Capabilities 4.4.4. Slot Capabilities 4.4.5. Power Management 4.4.6. Vendor Specific Extended Capability (VSEC)
5. Designing with the IP Core x
5.1. Generation 5.2. Simulation 5.3. IP Core Generation Output ( Quartus® Prime Pro Edition) 5.4. Channel Layout and PLL Usage
6. Block Descriptions x
6.1. Interfaces
6.1. Interfaces x
6.1.1. Stratix® 10 DMA Avalon-MM DMA Interface to the Application Layer 6.1.2. Avalon-MM Interface to the Application Layer 6.1.3. Clocks and Reset 6.1.4. Interrupts 6.1.5. Flush Requests 6.1.6. Serial Data, PIPE, Status, Reconfiguration, and Test Interfaces
6.1.1. Stratix® 10 DMA Avalon-MM DMA Interface to the Application Layer x
6.1.1.1. Descriptor Controller Interfaces when Instantiated Internally 6.1.1.2. Write DMA Avalon-MM Master Port 6.1.1.3. Descriptor Controller Interfaces when Instantiated Externally
6.1.1.1. Descriptor Controller Interfaces when Instantiated Internally x
6.1.1.1.1. Read Data Mover 6.1.1.1.2. Read Descriptor Controller Avalon-MM Master interface 6.1.1.1.3. Write Descriptor Controller Avalon-MM Master Interface 6.1.1.1.4. Read Descriptor Table Avalon-MM Slave Interface 6.1.1.1.5. Write Descriptor Table Avalon-MM Slave Interface
6.1.1.3. Descriptor Controller Interfaces when Instantiated Externally x
6.1.1.3.1. Avalon® -ST Descriptor Source
6.1.2. Avalon-MM Interface to the Application Layer x
6.1.2.1. Bursting and Non-Bursting Avalon® -MM Module Signals 6.1.2.2. Non-Bursing Slave Module 6.1.2.3. 32-Bit Control Register Access (CRA) Slave Signals 6.1.2.4. Bursting Slave Module
6.1.3. Clocks and Reset x
6.1.3.1. Clocks 6.1.3.2. Resets
6.1.4. Interrupts x
6.1.4.1. MSI Interrupts for Endpoints 6.1.4.2. Legacy Interrupts
6.1.6. Serial Data, PIPE, Status, Reconfiguration, and Test Interfaces x
6.1.6.1. Serial Data Interface 6.1.6.2. PIPE Interface 6.1.6.3. Hard IP Status Interface 6.1.6.4. Hard IP Reconfiguration 6.1.6.5. Test Interface
7. Registers x
7.1. Configuration Space Registers 7.2. Avalon-MM DMA Bridge Registers
7.1. Configuration Space Registers x
7.1.1. Register Access Definitions 7.1.2. PCI Configuration Header Registers 7.1.3. PCI Express Capability Structures 7.1.4. Intel Defined VSEC Capability Header 7.1.5. Uncorrectable Internal Error Status Register 7.1.6. Uncorrectable Internal Error Mask Register 7.1.7. Correctable Internal Error Status Register 7.1.8. Correctable Internal Error Mask Register
7.1.4. Intel Defined VSEC Capability Header x
7.1.4.1. Intel Defined Vendor Specific Header 7.1.4.2. Intel Marker 7.1.4.3. JTAG Silicon ID 7.1.4.4. User Configurable Device and Board ID
7.2. Avalon-MM DMA Bridge Registers x
7.2.1. PCI Express Avalon-MM Bridge Register Address Map 7.2.2. DMA Descriptor Controller Registers
7.2.1. PCI Express Avalon-MM Bridge Register Address Map x
7.2.1.1. Avalon-MM to PCI Express Interrupt Status Registers 7.2.1.2. Avalon-MM to PCI Express Interrupt Enable Registers 7.2.1.3. Address Mapping for High-Performance Avalon-MM 32-Bit Slave Modules 7.2.1.4. PCI Express to Avalon-MM Interrupt Status and Enable Registers for Endpoints 7.2.1.5. PCI Express Configuration Information Registers
7.2.2. DMA Descriptor Controller Registers x
7.2.2.1. Read DMA Internal Descriptor Controller Registers 7.2.2.2. Write DMA Internal Descriptor Controller Registers
8. Programming Model for the DMA Descriptor Controller x
8.1. Read DMA Example 8.2. Write DMA Example 8.3. Software Program for Simultaneous Read and Write DMA 8.4. Read DMA and Write DMA Descriptor Format
9. Programming Model for the Avalon® -MM Root Port x
9.1. Root Port TLP Data Control and Status Registers 9.2. Sending a TLP 9.3. Receiving a Non-Posted Completion TLP 9.4. Example of Reading and Writing BAR0 Using the CRA Interface
10. Avalon-MM Testbench and Design Example x
10.1. Avalon-MM Endpoint Testbench 10.2. Endpoint Design Example 10.3. Avalon® -MM Test Driver Module 10.4. Root Port BFM 10.5. BFM Procedures and Functions
10.2. Endpoint Design Example x
10.2.1. BAR Setup
10.4. Root Port BFM x
10.4.1. Overview 10.4.2. Issuing Read and Write Transactions to the Application Layer 10.4.3. Configuration of Root Port and Endpoint 10.4.4. Configuration Space Bus and Device Numbering 10.4.5. BFM Memory Map
10.5. BFM Procedures and Functions x
10.5.1. ebfm_barwr Procedure 10.5.2. ebfm_barwr_imm Procedure 10.5.3. ebfm_barrd_wait Procedure 10.5.4. ebfm_barrd_nowt Procedure 10.5.5. ebfm_cfgwr_imm_wait Procedure 10.5.6. ebfm_cfgwr_imm_nowt Procedure 10.5.7. ebfm_cfgrd_wait Procedure 10.5.8. ebfm_cfgrd_nowt Procedure 10.5.9. BFM Configuration Procedures 10.5.10. BFM Shared Memory Access Procedures 10.5.11. BFM Log and Message Procedures 10.5.12. Verilog HDL Formatting Functions
10.5.9. BFM Configuration Procedures x
10.5.9.1. ebfm_cfg_rp_ep Procedure 10.5.9.2. ebfm_cfg_decode_bar Procedure
10.5.10. BFM Shared Memory Access Procedures x
10.5.10.1. Shared Memory Constants 10.5.10.2. shmem_write Task 10.5.10.3. shmem_read Function 10.5.10.4. shmem_display Verilog HDL Function 10.5.10.5. shmem_fill Procedure 10.5.10.6. shmem_chk_ok Function
10.5.11. BFM Log and Message Procedures x
10.5.11.1. ebfm_display Verilog HDL Function 10.5.11.2. ebfm_log_stop_sim Verilog HDL Function 10.5.11.3. ebfm_log_set_suppressed_msg_mask Task 10.5.11.4. ebfm_log_set_stop_on_msg_mask Verilog HDL Task 10.5.11.5. ebfm_log_open Verilog HDL Function 10.5.11.6. ebfm_log_close Verilog HDL Function
10.5.12. Verilog HDL Formatting Functions x
10.5.12.1. himage1 10.5.12.2. himage2 10.5.12.3. himage4 10.5.12.4. himage8 10.5.12.5. himage16 10.5.12.6. dimage1 10.5.12.7. dimage2 10.5.12.8. dimage3 10.5.12.9. dimage4 10.5.12.10. dimage5 10.5.12.11. dimage6 10.5.12.12. dimage7
11. Document Revision History x
11.1. Document Revision History for the L-Tile and H-Tile Avalon® Memory-mapped Intel® FPGA IP for PCI Express* User Guide
A. PCI Express Core Architecture x
A.1. Transaction Layer A.2. Data Link Layer A.3. Physical Layer
C. Troubleshooting and Observing the Link Status x
C.1. Troubleshooting C.2. PCIe Link Inspector Overview
C.1. Troubleshooting x
C.1.1. Simulation Fails To Progress Beyond Polling.Active State C.1.2. Hardware Bring-Up Issues C.1.3. Link Training C.1.4. Use Third-Party PCIe Analyzer
C.2. PCIe Link Inspector Overview x
C.2.1. PCIe* Link Inspector Hardware
C.2.1. PCIe* Link Inspector Hardware x
C.2.1.1. Enabling the PCIe* Link Inspector C.2.1.2. Launching the PCIe* Link Inspector C.2.1.3. The PCIe* Link Inspector LTSSM Monitor C.2.1.4. Accessing the Configuration Space and Transceiver Registers C.2.1.5. Additional Status Commands
C.2.1.3. The PCIe* Link Inspector LTSSM Monitor x
C.2.1.3.1. LTSSM Monitor Registers C.2.1.3.2. ltssm_save2file <file_name> C.2.1.3.3. ltssm_file2console C.2.1.3.4. ltssm_debug_check C.2.1.3.5. ltssm_display <num_states> C.2.1.3.6. ltssm_save_oldstates
C.2.1.4. Accessing the Configuration Space and Transceiver Registers x
C.2.1.4.1. PCIe* Link Inspector Commands C.2.1.4.2. NPDME PLL and Channel Commands C.2.1.4.3. Register Address Map
C.2.1.5. Additional Status Commands x
C.2.1.5.1. Displaying PLL Lock and Calibration Status Registers
1. Introduction
2. Quick Start Guide
3. Interface Overview
4. Parameters
5. Designing with the IP Core
6. Block Descriptions
7. Registers
8. Programming Model for the DMA Descriptor Controller
9. Programming Model for the Avalon® -MM Root Port
10. Avalon-MM Testbench and Design Example
11. Document Revision History
A. PCI Express Core Architecture
B. Root Port Enumeration
C. Troubleshooting and Observing the Link Status

7.2.2.1. Read DMA Internal Descriptor Controller Registers

Figure 57. Address Offsets for Read DMA and Write DMA Internal Descriptor Controller Registers

The internal Read DMA Descriptor registers provide the following information:

  • Original location of descriptor table in host memory.
  • Required location of descriptor table in the internal Endpoint read controller FIFO memory.
  • Table size. The maximum size is 128 entries. Each entry is 32 bytes. The memory requirement is 4096 KB.
  • Additional fields to track completion of the DMA descriptors.

When you choose an internal these registers are accessed through the Read Descriptor Controller Slave.When you choose an externally instantiated Descriptor Controller these registers are accessed through BAR0. The Endpoint read controller FIFO is at offset 0x0000

The following table describes the registers in the internal Read DMA Descriptor Controller and specifies their offsets. These registers are accessed through the Read Descriptor Controller Slave. When you choose an externally instantiated DMA Descriptor Controller, these registers are accessed through a user-defined BAR. Software must add the address offsets to the base address, RdDC_SLV_ADDR of the Read DMA Descriptor Controller. When you choose an internal Descriptor Controller these registers are accessed through BAR0. The Read DMA Descriptor Controller registers start at offset 0x0000.

Table 70.  Read DMA Descriptor Controller Registers

Address Offset

Register

Access

Description

Reset Value

0x0000

Read Status and Descriptor Base (Low)

RW

Specifies the lower 32-bits of the base address of the read status and descriptor table in the PCIe* system memory. This address must be on a 32-byte boundary.

Unknown

0x0004

Read Status and Descriptor Base (High)

RW

Specifies the upper 32-bits of the base address of the read status and descriptor table in the PCIe* system memory.

Unknown

0x0008

Read Descriptor FIFO Base (Low)

RW

Specifies the lower 32 bits of the base address of the read descriptor FIFO in Endpoint memory.The address must be the Avalon-MM address of the Descriptor Controller's Read Descriptor Table Avalon-MM Slave Port as seen by the Read Data Mover Avalon-MM Master Port.

Unknown

0x000C

Read Descriptor FIFO Base (High)

RW

Specifies the upper 32 bits of the base address of the read descriptor FIFO in Endpoint Avalon-MM memory. This must be the Avalon-MM address of the descriptor controller's Read Descriptor Table Avalon-MM Slave Port as seen by the Read Data Mover Avalon-MM Master Port.

Unknown

0x0010

RD_DMA_LAST_PTR

RW

[31:8]: Reserved.

[7:0]: DescriptorID.

When read, returns the ID of the last descriptor requested. If the DMA is in reset, returns a value 0xFF.

When written, specifies the ID of the last descriptor requested. The difference between the value read and the value written is the number of descriptors to be processed.

For example, if the value reads 4, the last descriptor requested is 4. To specify 5 more descriptors, software should write a 9 into the RD_DMA_LAST_PTR register. The DMA executes 5 more descriptors.

To have the read DMA record the Update bit of every descriptor, program this register to transfer one descriptor at a time, or set the Update bit in the RD_CONTROL register.

The descriptor ID loops back to 0 after reaching RD_TABLE_SIZE.

If you want to process more pointers than RD_TABLE_SIZE - RD_DMA_LAST_PTR, you must proceed in two steps. First, process pointers up to RD_TABLE_SIZE by writing the same value as is in RD_TABLE_SIZE, Wait for that to complete. Then, write the number of remaining descriptors to RD_DMA_LAST_PTR.

[31:8]: Unknown

[7:0]:0xFF
0x0014 RD_TABLE_SIZE

RW

[31:7]: Reserved.

[6:0]: Size -1.

This register provides for a table size less than the default size of 128 entries. The smaller size saves memory. Program this register with the value desired -1.

This value specifies the last Descriptor ID.

[31:7]: Unknown

[6:0]: 0x7F
0x0018 RD_CONTROL

RW

[31:1]: Reserved.

[0]: Update.

Controls how the descriptor processing status is reported. When the Update bit is set, returns status for every descriptor processed. If not set, then sends status back for latest entry in the RD_DMA_LAST_PTR register.

The default value is 0.

[31:1]: Unknown

[0]: 0x0
Level Two Title