Intel® Acceleration Stack User Guide: Intel FPGA Programmable Acceleration Card N3000-N/2

Download
ID 683362
Date 11/01/2021
Public
Document Table of Contents
Document Table of Contents x
1. About this Document 2. System Requirements 3. Hardware Installation 4. Installing the OPAE Software 5. Identify the Intel® MAX® 10 BMC Version 6. Intel XL710 Driver Installation and Firmware Update 7. Updating the Retimer Firmware 8. OPAE Tools 9. Sample Test: Native Loopback 10. Configuring Ethernet Interfaces 11. Testing Network Loopback Using Data Plane Development Kit (DPDK) 12. Graceful Shutdown 13. Single Event Upset (SEU) 14. Document Revision History for Intel Acceleration Stack User Guide: Intel® FPGA PAC N3000-N/2 A. Troubleshooting B. fpgabist Sample Output
1. About this Document x
1.1. Acronym List
3. Hardware Installation x
3.1. Installing the Intel® FPGA PAC N3000-N/2
4. Installing the OPAE Software x
4.1. Install the Release Package
4.1. Install the Release Package x
4.1.1. Remove Previous OPAE Packages 4.1.2. Install the Acceleration Stack for Runtime 4.1.3. Install the Acceleration Stack for Development 4.1.4. Verify the OPAE Installation
4.1.2. Install the Acceleration Stack for Runtime x
4.1.2.1. For RHEL 4.1.2.2. For CentOS
4.1.2.2. For CentOS x
4.1.2.2.1. Download kernel 4.19 4.1.2.2.2. Build and Install kernel 4.19 4.1.2.2.3. Install OPAE in kernel 4.19
5. Identify the Intel® MAX® 10 BMC Version x
5.1. FPGA Factory Image Overview
6. Intel XL710 Driver Installation and Firmware Update x
6.1. Installing the Intel XL710 Driver 6.2. Updating the Intel XL710 Firmware
8. OPAE Tools x
8.1. Using fpgasupdate 8.2. Using fpgainfo 8.3. Test PCIe and External Memories with fpgabist 8.4. Test Network Loopback using fpgadiag
10. Configuring Ethernet Interfaces x
10.1. Modifying the Interface Maximum Transmission Unit (MTU) Size 10.2. Setting Forward Error Correction (FEC) Mode 10.3. Ethernet Pause Flow Control 10.4. Get Link Statistics 10.5. Ethernet Link Status
11. Testing Network Loopback Using Data Plane Development Kit (DPDK) x
11.1. Test Using an External Traffic Generator 11.2. Revert Back from DPDK to OPAE
12. Graceful Shutdown x
12.1. Using OPAE
13. Single Event Upset (SEU) x
13.1. OPAE Handling of SEU
A. Troubleshooting x
A.1. If OPAE installation verification fails, how to install OPAE manually?
B. fpgabist Sample Output x
B.1. For 4x25G Configuration B.2. For 2x2x25G Configuration
1. About this Document
2. System Requirements
3. Hardware Installation
4. Installing the OPAE Software
5. Identify the Intel® MAX® 10 BMC Version
6. Intel XL710 Driver Installation and Firmware Update
7. Updating the Retimer Firmware
8. OPAE Tools
9. Sample Test: Native Loopback
10. Configuring Ethernet Interfaces
11. Testing Network Loopback Using Data Plane Development Kit (DPDK)
12. Graceful Shutdown
13. Single Event Upset (SEU)
14. Document Revision History for Intel Acceleration Stack User Guide: Intel® FPGA PAC N3000-N/2
A. Troubleshooting
B. fpgabist Sample Output

8.4. Test Network Loopback using fpgadiag

The test requires use of an external traffic generator to send traffic through QSFP ports, the --side host enables loopback on the host side of the Intel® Arria® 10 FPGA. 
$	sudo fpgadiag -B 0x3e -m fpgalpbk --side host –-direction remote –-enable
To disable: 
$	sudo fpgadiag -B 0x3e -m fpgalpbk --side host –-direction remote --disable
Note: Since all four Ethernet channels in the 4x25G configuration are in QSFP A, only one QSFP port indicates linkup status through LEDs.
Level Two Title

Did you find the information on this page useful?

Characters remaining:

Feedback Message