MAX® 10 External Memory Interface User Guide

Download PDF
ID 683087
Date 3/17/2025
Public
Document Table of Contents
Document Table of Contents x
1. MAX® 10 External Memory Interface Overview 2. MAX® 10 External Memory Interface Architecture and Features 3. MAX® 10 External Memory Interface Design Considerations 4. MAX® 10 External Memory Interface Implementation Guides 5. UniPHY IP References for MAX® 10 Devices 6. MAX® 10 External Memory Interface User Guide Archives 7. Document Revision History for the MAX® 10 External Memory Interface User Guide
1. MAX® 10 External Memory Interface Overview x
1.1. MAX® 10 External Memory Interface Support and Performance
2. MAX® 10 External Memory Interface Architecture and Features x
2.1. MAX® 10 I/O Banks for External Memory Interface 2.2. MAX® 10 DQ/DQS Groups 2.3. MAX® 10 External Memory Interfaces Maximum Width 2.4. MAX® 10 Memory Controller 2.5. MAX® 10 External Memory Read Datapath 2.6. MAX® 10 External Memory Write Datapath 2.7. MAX® 10 Address/Command Path 2.8. MAX® 10 PHY Clock (PHYCLK) Network 2.9. Phase Detector for VT Tracking 2.10. On-Chip Termination 2.11. Phase-Locked Loop 2.12. MAX® 10 Low Power Feature
2.5. MAX® 10 External Memory Read Datapath x
2.5.1. DDR Input Registers
2.6. MAX® 10 External Memory Write Datapath x
2.6.1. DDR Output Registers
3. MAX® 10 External Memory Interface Design Considerations x
3.1. MAX® 10 DDR2 and DDR3 Design Considerations 3.2. LPDDR2 Design Considerations 3.3. Guidelines: DDR3, DDR2, and LPDDR2 External Memory Interface I/O Limitation 3.4. Guidelines: Board Design Requirement for DDR2, DDR3, and LPDDR2 3.5. Guidelines: Reading the MAX® 10 Pin-Out Files
3.1. MAX® 10 DDR2 and DDR3 Design Considerations x
3.1.1. DDR2/DDR3 External Memory Interface Pins 3.1.2. DDR2/DDR3 Recommended Termination Schemes for MAX® 10 Devices
3.1.1. DDR2/DDR3 External Memory Interface Pins x
3.1.1.1. MAX® 10 Data and Data Clock (Data Strobe) Pins 3.1.1.2. Data Mask Pins 3.1.1.3. DDR2/DDR3 Error Correction Coding Pins 3.1.1.4. DDR2/DDR3 Address and Control/Command Pins 3.1.1.5. Memory Clock Pins
3.1.1.1. MAX® 10 Data and Data Clock (Data Strobe) Pins x
3.1.1.1.1. MAX® 10 I/O Bank DQ/DQS Support for DDR2/DDR3
3.2. LPDDR2 Design Considerations x
3.2.1. LPDDR2 External Memory Interface Pins 3.2.2. LPPDDR2 Power Supply Variation Constraint 3.2.3. LPDDR2 Recommended Termination Schemes for MAX® 10 Devices
3.2.1. LPDDR2 External Memory Interface Pins x
3.2.1.1. MAX® 10 Data and Data Clock (Data Strobe) Pins 3.2.1.2. Data Mask Pins 3.2.1.3. LPDDR2 Address and Control/Command Pins 3.2.1.4. Memory Clock Pins
3.2.1.1. MAX® 10 Data and Data Clock (Data Strobe) Pins x
3.2.1.1.1. MAX® 10 I/O Bank DQ/DQS Support for LPDDR2
4. MAX® 10 External Memory Interface Implementation Guides x
4.1. UniPHY IP Core 4.2. LPDDR2 External Memory Interface Implementation 4.3. DDR2 and DDR3 External Memory Interface Implementation
4.2. LPDDR2 External Memory Interface Implementation x
4.2.1. Supported LPDDR2 Topology
4.3. DDR2 and DDR3 External Memory Interface Implementation x
4.3.1. MAX® 10 Supported DDR2 or DDR3 Topology
5. UniPHY IP References for MAX® 10 Devices x
5.1. UniPHY Parameter Settings for MAX® 10
5.1. UniPHY Parameter Settings for MAX® 10 x
5.1.1. UniPHY Parameters—PHY Settings 5.1.2. UniPHY Parameters—Memory Parameters 5.1.3. UniPHY Parameters—Memory Timing 5.1.4. UniPHY Parameters—Board Settings 5.1.5. UniPHY Parameters—Controller Settings 5.1.6. UniPHY Parameters—Diagnostics
1. MAX® 10 External Memory Interface Overview
2. MAX® 10 External Memory Interface Architecture and Features
3. MAX® 10 External Memory Interface Design Considerations
4. MAX® 10 External Memory Interface Implementation Guides
5. UniPHY IP References for MAX® 10 Devices
6. MAX® 10 External Memory Interface User Guide Archives
7. Document Revision History for the MAX® 10 External Memory Interface User Guide

3.4. Guidelines: Board Design Requirement for DDR2, DDR3, and LPDDR2

  • For DDR2, DDR3, and LPDDR2 interfaces, the maximum board skew between pins must be lower than 40 ps. This guideline applies to all pins (address, command, clock, and data).
  • To minimize unwanted inductance from the board via, Altera recommends that you keep the PCB via depth for VCCIO banks below 49.5 mil.
  • For devices with DDR3 interface implementation, onboard termination is required for the DQ, DQS, and address signals. Altera recommends that you use termination resistor value of 80 Ω to VTT.
  • For the DQ, address, and command pins, keep the PCB trace routing length less than six inches for DDR3, or less than three inches for LPDDR2.
Related Information
Level Two Title