F-Tile Interlaken Intel® FPGA IP Design Example User Guide

Download PDF
ID 683069
Date 12/04/2023
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. Quick Start Guide 2. Design Example Description 3. F-Tile Interlaken Intel® FPGA IP Design Example User Guide Archives 4. Document Revision History for F-Tile Interlaken Intel® FPGA IP Design Example User Guide
1. Quick Start Guide x
1.1. Hardware and Software Requirements 1.2. Generating the Design 1.3. Directory Structure 1.4. Simulating the Design Example Testbench 1.5. Compiling and Configuring the Hardware Design Example 1.6. Testing the Hardware Design Example
2. Design Example Description x
2.1. Design Example Components 2.2. Analog Parameters Settings 2.3. Design Example Flow 2.4. Interface Signals 2.5. Register Map 2.6. Reset
1. Quick Start Guide
2. Design Example Description
3. F-Tile Interlaken Intel® FPGA IP Design Example User Guide Archives
4. Document Revision History for F-Tile Interlaken Intel® FPGA IP Design Example User Guide

1.4. Simulating the Design Example Testbench

Figure 6. Procedure
Follow these steps to simulate the testbench:
  1. At the command prompt, change to the testbench simulation directory. The directory path is <design_example_installation_dir>/example_design/testbench.
  2. Run the simulation script for the supported simulator of your choice. The script compiles and runs the testbench in the simulator. Your script should check that the SOP and EOP counts match after simulation is complete.
    Table 5.  Steps to Run Simulation
    Simulator Instructions
    VCS* In the command line, type: 
    sh run_vcs.sh
    VCS* MX In the command line, type: 
    sh run_vcsmx.sh
    QuestaSim* or Questa*-Intel® FPGA Edition
    In the command line, type: 
    vsim -do run_mentor.tcl
    If you prefer to simulate without bringing up the GUI, type: 
    vsim -c -do run_mentor.tcl
    Xcelium* In the command line, type: 
    sh run_xcelium.sh
  3. Analyze the results. A successful simulation sends and receives packets, and displays "Test PASSED".
    The testbench for the design example completes the following tasks:
    • Instantiates the F-Tile Interlaken Intel® FPGA IP core.
    • Prints PHY status.
    • Checks metaframe synchronization (SYNC_LOCK) and word (block) boundaries (WORD_LOCK).
    • Waits for individual lanes to be locked and aligned.
    • Starts transmitting packets.
    • Checks packet statistics:
      • CRC24 errors
      • SOPs
      • EOPs
    The following sample output illustrates a successful simulation test run: 
    ******************************************
				INFO: Waiting for lanes to be aligned
	  				All of the receiver lanes are aligned and are ready to receive traffic.
***************************************************

***************************************************
				INFO: Start transmitting packets
***************************************************

***************************************************
				INFO: Stop transmitting packets
***************************************************

***************************************************
				INFO: Checking packets statistics
***************************************************

				CRC 24 errors reported: 0
				SOPs transmitted: 100
				EOPs transmitted: 100
				SOPs received: 100
				EOPs received: 100
				ECC error count: 0

***************************************************
				INFO: Test PASSED
***************************************************
    Note: The Interlaken design example simulation testbench sends 100 packets and receives 100 packets.
    The following sample output illustrates a successful simulation test run for Interlaken Look-aside mode: 
    -------------------------------------------------
   check if rx received all of pkt from tx
-------------------------------------------------

-------------------------------------------------
   rx received all of pkt from tx
-------------------------------------------------

-------------------------------------------------
   Check CRC32 errors
-------------------------------------------------
   CRC32 PASS

-------------------------------------------------
   Check TX and RX Counter equal or not
-------------------------------------------------

-------------------------------------------------
   De-assert Counter equal bit
-------------------------------------------------

-------------------------------------------------
   RX_SOP COUNTER
-------------------------------------------------

-------------------------------------------------
   RX_EOP COUNTER
-------------------------------------------------


-------------------------------------------------
   Display Final Report
-------------------------------------------------
     0 Detected Error
     0 CRC24 errors reported
       273 SOPs transmitted
       273 EOPs transmitted
       273 SOPs received
       273 EOPs received
-------------------------------------------------

-------------------------------------------------
   Finish Simulation
-------------------------------------------------

-------------------------------------------------
   TEST PASSED
--------------------------------------------------
Level Two Title