F-Tile Low Latency 50G Ethernet Intel® FPGA Soft-IP User Guide

ID 758946
Date 5/10/2023
Public
Document Table of Contents

8.3. Pause/PFC Flow Control Registers

Some of the registers in this table cannot be updated during normal operation.
Table 23.  TX Flow Control Registers
Addr Bit Name Description Reset Access
0x600 31:0 TX Flow Control Revision ID

Specifies the revision ID, "50GEFCTx CSR".

TBD

RO
0x601 31:0 TX Flow Control Scratch Pad Scratch register for testing. 0 RW
0x602 31:0 TX Flow Control IP Core Variant 0

Specifies first 4 characters of IP core variation identifier ASCII string, "50GE ".

TBD

RO
0x603 31:0 TX Flow Control IP Core Variant 1 Next 4 characters of IP core variation identifier ASCII string, "FCTx". 0x4643_5478 RO
0x604 31:0 TX Flow Control IP Core Variant 2

Final 4 characters of IP core variation identifier ASCII string, "0CSR". The "0" is unprintable.

0x0043_5352 RO
0x605

(FCQN-1):0

TX Flow Control Enable

Enables the IP core to generate XON and XOFF Pause/PFC flow control frames to the remote partner. The following encodings are defined:
  • 1'b0: XON or XOFF Pause/PFC flow control is disabled.
  • 1'b1: XON or XOFF Pause/PFC flow control is enabled.

You can change this field dynamically.

1'b1 in each bit that corresponds to a queue

RW

31:FCQN

Reserved Reserved 0 RO
0x606

(FCQN-1):0

TX Flow Control CSR XON/XOFF Request 0

One bit per queue

XON/XOF flow control frame request bit 0. Interpretation depends on whether the IP core is in 1-bit FC request mode or in 2-bit FC request mode. This register affects a flow control queue only if the corresponding bit of the TX Flow Control Enable register has the value of 1.

In 2-bit mode, in addition, this register is active for a specific flow control queue only if the corresponding bit in the TX 2-bit Flow Control Request Mode register field (bits [(FCQN-1):0] of the register at offset 0x641) specifies that the flow control logic accepts input from this register.

The following encodings are defined for 1-bit mode. The IP core reads the 1-bit mode value in TX Flow Control CSR XON/XOFF Request 0.

  • 0 = No request
  • 0 to 1 = Generate XOFF request
  • 1 = Continue to generate XOFF request
  • 1 to 0 = Generate XON request

The following encodings are defined for 2-bit mode. The IP core reads the 2-bit mode value in {TX Flow Control CSR XON/XOFF Request 1, TX Flow Control CSR XON/XOFF Request 1}.

  • 00 = No request
  • 01 = XON request
  • 10 = XOFF request
  • 11 = Invalid

You can modify the value of this field dynamically.

0 RW

15:FCQN

Reserved Reserved 0 RO

(FCQN+15):16

TX Flow Control CSR XON/XOFF Request 1

1-bit per queue

In conjunction with Flow Control XON/XOFF Request 0 specifies a 2-bit request for XON/XOFF flow control frame transmission. This bit is the upper bit of the 2-bit control field.

You can change the value of this field dynamically.

0 RW

31:(FCQN+16)

Reserved Reserved 0 RO
0x607 31:0 Reserved Reserved N/A RO
0x608 31:0 Reserved Reserved N/A RO
0x609 31:0 Reserved Reserved N/A RO
0x60A 0

TX Pause Enable

1-bit

Determines whether receiving a valid Pause frame stops TX user data transmission.

1'b0: Transmission is not stopped

1'b1: Transmission stops

You cannot change the value of this field dynamically.

0 RW
31:1 Reserved Reserved 0 RO
0x60B 31:0 Reserved Reserved N/A RO
0x60C 31:0 Reserved Reserved N/A RO
0x60D 31:0 TX Flow Control Destination Address Lower

Specifies the 48-bit Destination Address of the flow control frame. Contains the 32 LSB of the address field.

You cannot modify the value of this field dynamically.

0xC2000001 RW
0x60E 15:0 TX Flow Control Destination Address Upper

Specifies the 48-bit Destination Address of flow control frame. Contains the 16 MSB of the address field.

You cannot modify the value of this field dynamically.

0x0180 RW
31:16 Reserved Reserved 0 RO
0x60F 31:0 TX Flow Control Source Address Lower

Specifies the 48-bit Source Address of flow control frame. Contains the 32 LSB of the address field.

0xCBFC5ADD RW
0x610 15:0 TX Flow Control Source Address Upper

Specifies the 48-bit Source Address of flow control frame. Contains the 16 MSB of the address field.

You cannot modify the value of this field dynamically.

0xE100 RW
31:16 Reserved Reserved 0 RO

0x620 + (QN), where QN = 0 to 7

15:0

TX Flow Control Quanta

16-bit per queue

Specifies the pause quanta of Pause/PFC flow control frames to be sent to remote partner.

You cannot modify the value of this field dynamically.

0xFFFF RW
31:16 Reserved Reserved 0 RO
0x628 + (QN), where QN = 0 to 7 15:0

TX Flow Control Signal XOFF Request Hold Quanta

16-bit per queue

Specifies the separation between 2 consecutive XOFF flow control frames.

You cannot modify the value of this field dynamically.

0xFFFF RW
31:16 Reserved Reserved 0 RO
0x640 0

TX Flow Control Select

1-bit

Specifies whether the TX hardware generates Pause or PFC frames. Affects only PFC Queue 0.

Usage example:

You can synthesize a single PFC queue and use it for both Pause and PFC purpose.

1'b0: Pause

1'b1: PFC

You cannot modify the value of this field dynamically.

1 RW
31:1 Reserved. Reserved. 0 RO
0x641 (FCQN-1):0

TX 2-bit Flow Control Request Mode

1-bit for all FQCN

Determines whether the TX Flow Control CSR XON/XOFF Request register or the pause_insert_tx0 and pause_insert_tx1 signals control XON/XOFF mode in 2-bit control mode.

1'b0: The pause_insert_tx0 and pause_insert_tx1 signals control requests

1'b1: The TX Flow Control CSR XON/XOFF Request register fields control requests

You cannot modify the value of this field dynamically.

0 RW
16

TX Flow Control Request Mode

1 bit for all queues

Determines whether the IP core is in TX flow control 1-bit mode or 2-bit mode.

1'b0: Use 1-bit mode to make TX flow control requests

1'b1: Use 2-bit mode to make TX flow control requests

0 RW
31:17 Reserved Reserved 0 RO
Table 24.  RX Flow Control Registers
Addr Bit Name Description Reset Access
0x700 31:0 RX Flow Control Revision ID

Provides the flow control revision, "50GEFCRx CSR".

0x0916 2016 RO
0x701 31:0 RX Flow Control Scratch Pad Provides a register for debug. 0 RW
0x702 31:0 RX Flow Control IP Core Variant 0

First 4 characters of IP core variation identifier ASCII string,

"50GE".

0x3235_4745

RO
0x703 31:0 RX Flow Control IP Core Variant 1 Next 4 characters of IP core variation identifier ASCII string, "FCRx". 0x4643_5278 RO
0x704 31:0 RX Flow Control IP Core Variant 2 Final 4 characters of IP core variation identifier ASCII string, "0CSR". The "0" is unprintable. 0x0043_5352 RO
0x705 (FCQN-1):0]

RX PFC Enable

1 bit per queue

Determines whether receiving a valid PFC frame causes the PFC duration user interface to indicate a valid pause quanta duration to the user logic.

1'b0: Disable

1'b1: Enable

You cannot modify the value of this field dynamically.

1'b1 in each bit that corresponds to a queue RW
31:FCQN Reserved Reserved 0 RO
0x706 31:0 Reserved Reserved N/A RO
0x707 31:0 RX Flow Control Destination Address Lower

Specifies the 48-bit Destination Address of the flow control frame. Contains the 32 LSB of the address field.

You cannot modify the value of this field dynamically.

0xC2000001 RW
0x708 15:0 RX Flow Control Destination Address Upper

Specifies the 48-bit Destination Address of flow control frame. Contains the 16 MSB of the address field.

You cannot modify the value of this field dynamically.

0x0180 RW
31:16 Reserved Reserved 0 RO

Did you find the information on this page useful?

Characters remaining:

Feedback Message