F-Tile JESD204B Intel® FPGA IP User Guide

Download PDF
ID 723907
Date 4/23/2024
Public
Document Table of Contents
Document Table of Contents x
1. F-Tile JESD204B IP Quick Reference 2. About the F-Tile JESD204B Intel® FPGA IP 3. Getting Started 4. F-Tile JESD204B IP Functional Description 5. F-Tile JESD204B IP Deterministic Latency Implementation Guidelines 6. F-Tile JESD204B IP Debug Guidelines 7. F-Tile JESD204B Intel FPGA IP User Guide Archives 8. Document Revision History for the F-Tile JESD204B Intel® FPGA IP User Guide
2. About the F-Tile JESD204B Intel® FPGA IP x
2.1. Release Information 2.2. Device Family Support 2.3. Datapath Modes 2.4. IP Variation 2.5. F-Tile JESD204B IP Configuration 2.6. Channel Bonding 2.7. Performance and Resource Utilization
3. Getting Started x
3.1. Introduction to Intel® FPGA IP Cores 3.2. Installing and Licensing Intel® FPGA IP Cores 3.3. Intel® FPGA IP Evaluation Mode 3.4. Upgrading IP Cores 3.5. IP Catalog and Parameter Editor 3.6. Design Walkthrough 3.7. F-Tile JESD204B IP Design Considerations 3.8. F-Tile JESD204B Intel® FPGA IP Parameters 3.9. F-Tile JESD204B IP Component Files
3.6. Design Walkthrough x
3.6.1. Creating a New Quartus® Prime Project 3.6.2. Parameterizing and Generating the IP 3.6.3. Compiling the F-Tile JESD204B IP Core Design 3.6.4. Programming an FPGA Device
3.7. F-Tile JESD204B IP Design Considerations x
3.7.1. Integrating the F-Tile JESD204B IP in Platform Designer 3.7.2. Pin Assignments 3.7.3. Adding External System PLL
4. F-Tile JESD204B IP Functional Description x
4.1. Transmitter 4.2. Receiver 4.3. Operation 4.4. Clocking Scheme 4.5. Reset Scheme 4.6. Signals 4.7. Registers
4.1. Transmitter x
4.1.1. TX Data Link Layer 4.1.2. TX PHY Layer
4.1.1. TX Data Link Layer x
4.1.1.1. TX CGS 4.1.1.2. TX ILAS 4.1.1.3. User Data Phase
4.2. Receiver x
4.2.1. RX Data Link Layer 4.2.2. RX PHY Layer
4.2.1. RX Data Link Layer x
4.2.1.1. RX CGS 4.2.1.2. Frame Synchronization 4.2.1.3. Frame Alignment 4.2.1.4. Lane Alignment 4.2.1.5. ILAS Data 4.2.1.6. Initial Lane Synchronization
4.3. Operation x
4.3.1. Operating Modes 4.3.2. Scrambler/Descrambler 4.3.3. SYNC_N Signal 4.3.4. Link Reinitialization 4.3.5. Link Startup Sequence 4.3.6. Error Reporting Through SYNC_N Signal
4.3.1. Operating Modes x
4.3.1.1. Subclass 0 Operating Mode 4.3.1.2. Subclass 1 Operating Mode 4.3.1.3. Subclass 2 Operating Mode
4.4. Clocking Scheme x
4.4.1. Device Clock 4.4.2. Link Clock 4.4.3. Local MultiFrame Clock 4.4.4. Clock Correlation 4.4.5. System PLL Clock
4.5. Reset Scheme x
4.5.1. Reset Sequence 4.5.2. ADC–FPGA Subsystem Reset Sequence 4.5.3. FPGA–DAC Subsystem Reset Sequence
4.6. Signals x
4.6.1. Transmitter Signals 4.6.2. Receiver Signals
4.7. Registers x
4.7.1. Register Access Type Convention 4.7.2. Register Map and Definition 4.7.3. Transmitter Registers 4.7.4. Receiver Registers
5. F-Tile JESD204B IP Deterministic Latency Implementation Guidelines x
5.1. Constraining Incoming SYSREF Signal 5.2. Programmable RBD Offset 5.3. Programmable LMFC Offset 5.4. Maintaining Deterministic Latency during Link Reinitialization
6. F-Tile JESD204B IP Debug Guidelines x
6.1. Clocking Scheme 6.2. F-Tile JESD204B Parameters 6.3. SPI Programming 6.4. Converter and FPGA Operating Conditions 6.5. Signal Polarity and FPGA Pin Assignment
1. F-Tile JESD204B IP Quick Reference
2. About the F-Tile JESD204B Intel® FPGA IP
3. Getting Started
4. F-Tile JESD204B IP Functional Description
5. F-Tile JESD204B IP Deterministic Latency Implementation Guidelines
6. F-Tile JESD204B IP Debug Guidelines
7. F-Tile JESD204B Intel FPGA IP User Guide Archives
8. Document Revision History for the F-Tile JESD204B Intel® FPGA IP User Guide

2. About the F-Tile JESD204B Intel® FPGA IP

The F-Tile JESD204B Intel® FPGA IP is a high-speed point-to-point serial interface for digital-to-analog (DAC) or analog-to-digital (ADC) converters to transfer data to FPGA devices. This unidirectional serial interface runs at a maximum data rate of 20 Gbps. This protocol offers higher bandwidth, low I/O count and supports scalability in both number of lanes and data rates. The F-Tile JESD204B Intel® FPGA IP addresses multi-device synchronization by introducing Subclass 1 and Subclass 2 to achieve deterministic latency.
Note: The full product name, F-Tile JESD204B Intel® FPGA IP, is shortened to F-Tile JESD204B IP in this document.

The F-Tile JESD204B IP incorporates:

  • Media access control (MAC)—data link layer (DLL) block that controls the link states and character replacement.
  • Physical layer (PHY)—physical coding sublayer (PCS) and physical media attachment (PMA) block.

The F-Tile JESD204B IP does not incorporate the Transport Layer (TL) that controls the frame assembly and disassembly. The TL and test components are provided as part of a design example component where you can customize the design for different converter devices.

Figure 1. Typical System Application for F-Tile JESD204B IPThe F-Tile JESD204B IP uses the Avalon® streaming source and sink interfaces, with unidirectional flow of data, to transmit and receive data on the FPGA fabric interface.


Key features of the F-Tile JESD204B IP:
  • Data rate of up to 20 Gbps (characterization up to 12.5 G)
  • Subclass 0 mode for backward compatibility to JESD204A
  • Subclass 1 mode for deterministic latency support (using SYSREF) between the ADC/DAC and logic device
  • Subclass 2 mode for deterministic latency support (using SYNC_N) between the ADC/DAC and logic device
  • Multi-device synchronization

Section Content
Release Information
Device Family Support
Datapath Modes
IP Variation
F-Tile JESD204B IP Configuration
Channel Bonding
Performance and Resource Utilization

Related Information
Level Two Title