F-Tile 1G/2.5G/5G/10G Multi-rate Ethernet PHY Intel® FPGA IP User Guide

Download PDF
ID 720989
Date 2/23/2022
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. About the F-Tile 1G/2.5G/5G/10G Multi-rate Ethernet PHY Intel® FPGA IP User Guide 2. 1G/2.5G/5G/10G Multi-rate Ethernet PHY Intel® FPGA IP Overview 3. Getting Started 4. Functional Description 5. 1G/2.5G/5G/10G Multi-rate Ethernet PHY Intel® FPGA IP Parameters 6. Interface Signals 7. Configuration Registers A. Document Revision History for the F-Tile 1G/2.5G/5G/10G Multi-rate Ethernet PHY Intel® FPGA IP User Guide
2. 1G/2.5G/5G/10G Multi-rate Ethernet PHY Intel® FPGA IP Overview x
2.1. Release Information 2.2. Features 2.3. Device Family Support 2.4. Device Speed Grade Support 2.5. Resource Utilization
3. Getting Started x
3.1. Introduction to Intel® FPGA IP Cores 3.2. Installing and Licensing Intel® FPGA IP Cores 3.3. Specifying the IP Core Parameters and Options 3.4. Generated File Structure 3.5. Simulating Intel® FPGA IP Cores 3.6. Upgrading the 1G/2.5G/5G/10G Multi-rate Ethernet PHY Intel® FPGA IP Core 3.7. Integrating Your IP Core in Your Design
3.2. Installing and Licensing Intel® FPGA IP Cores x
3.2.1. Intel® FPGA IP Evaluation Mode
3.7. Integrating Your IP Core in Your Design x
3.7.1. Adding the F-tile Reference and System PLL IP
4. Functional Description x
4.1. Clocking and Reset Sequence 4.2. Timing Constraints 4.3. Switching Operation Speed 4.4. IEEE 802.3 Clause 37 Auto-Negotiation 4.5. USXGMII
4.1. Clocking and Reset Sequence x
4.1.1. Clocking 4.1.2. Reset
6. Interface Signals x
6.1. Clock Signals 6.2. Reset Signals 6.3. Serial Interface Signals 6.4. Avalon® Memory-Mapped Interface Signals 6.5. XGMII Signals 6.6. Transceiver Status and Transceiver Clock Status Signals 6.7. Reconfiguration Signals 6.8. Operating Speed and Status Signals
7. Configuration Registers x
7.1. Register Map 7.2. PHY Registers
1. About the F-Tile 1G/2.5G/5G/10G Multi-rate Ethernet PHY Intel® FPGA IP User Guide
2. 1G/2.5G/5G/10G Multi-rate Ethernet PHY Intel® FPGA IP Overview
3. Getting Started
4. Functional Description
5. 1G/2.5G/5G/10G Multi-rate Ethernet PHY Intel® FPGA IP Parameters
6. Interface Signals
7. Configuration Registers
A. Document Revision History for the F-Tile 1G/2.5G/5G/10G Multi-rate Ethernet PHY Intel® FPGA IP User Guide

7.1. Register Map

You can access the 32-bit configuration registers via the Avalon® memory-mapped interface as described in Avalon Memory-Mapped Interface Signals.
Table 23.  Register Map Overview
Address Range Usage Register Width Configuration
0x400–0x41F USXGMII 32 10M/100M/1G/2.5G/5G/10G (USXGMII)
Note: Refer to the F-tile Ethernet Hard IP User Guide and F-tile Architecture and PMA and FEC Direct PHY IP User Guide for register map of Ethernet and Transceiver Reconfiguration Interfaces.
Table 24.  Types of Register Access
Access Definition
RO Read only.
RW Read and write.
RWC Read, write, and clear. The user application writes 1 to the register bit(s) to invoke a defined instruction. The IP core clears the bit(s) upon executing the instruction.
Observe the following guidelines when accessing the registers:
  • Do not write to reserved or undefined registers.
  • When writing to the registers, perform read-modify-write operation to ensure that reserved or undefined register bits are not overwritten.
Related Information
Level Two Title