F-Tile 1G/2.5G/5G/10G Multi-rate Ethernet PHY Intel® FPGA IP User Guide

Download PDF
ID 720989
Date 2/23/2022
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. About the F-Tile 1G/2.5G/5G/10G Multi-rate Ethernet PHY Intel® FPGA IP User Guide 2. 1G/2.5G/5G/10G Multi-rate Ethernet PHY Intel® FPGA IP Overview 3. Getting Started 4. Functional Description 5. 1G/2.5G/5G/10G Multi-rate Ethernet PHY Intel® FPGA IP Parameters 6. Interface Signals 7. Configuration Registers A. Document Revision History for the F-Tile 1G/2.5G/5G/10G Multi-rate Ethernet PHY Intel® FPGA IP User Guide
2. 1G/2.5G/5G/10G Multi-rate Ethernet PHY Intel® FPGA IP Overview x
2.1. Release Information 2.2. Features 2.3. Device Family Support 2.4. Device Speed Grade Support 2.5. Resource Utilization
3. Getting Started x
3.1. Introduction to Intel® FPGA IP Cores 3.2. Installing and Licensing Intel® FPGA IP Cores 3.3. Specifying the IP Core Parameters and Options 3.4. Generated File Structure 3.5. Simulating Intel® FPGA IP Cores 3.6. Upgrading the 1G/2.5G/5G/10G Multi-rate Ethernet PHY Intel® FPGA IP Core 3.7. Integrating Your IP Core in Your Design
3.2. Installing and Licensing Intel® FPGA IP Cores x
3.2.1. Intel® FPGA IP Evaluation Mode
3.7. Integrating Your IP Core in Your Design x
3.7.1. Adding the F-tile Reference and System PLL IP
4. Functional Description x
4.1. Clocking and Reset Sequence 4.2. Timing Constraints 4.3. Switching Operation Speed 4.4. IEEE 802.3 Clause 37 Auto-Negotiation 4.5. USXGMII
4.1. Clocking and Reset Sequence x
4.1.1. Clocking 4.1.2. Reset
6. Interface Signals x
6.1. Clock Signals 6.2. Reset Signals 6.3. Serial Interface Signals 6.4. Avalon® Memory-Mapped Interface Signals 6.5. XGMII Signals 6.6. Transceiver Status and Transceiver Clock Status Signals 6.7. Reconfiguration Signals 6.8. Operating Speed and Status Signals
7. Configuration Registers x
7.1. Register Map 7.2. PHY Registers
1. About the F-Tile 1G/2.5G/5G/10G Multi-rate Ethernet PHY Intel® FPGA IP User Guide
2. 1G/2.5G/5G/10G Multi-rate Ethernet PHY Intel® FPGA IP Overview
3. Getting Started
4. Functional Description
5. 1G/2.5G/5G/10G Multi-rate Ethernet PHY Intel® FPGA IP Parameters
6. Interface Signals
7. Configuration Registers
A. Document Revision History for the F-Tile 1G/2.5G/5G/10G Multi-rate Ethernet PHY Intel® FPGA IP User Guide

3.3. Specifying the IP Core Parameters and Options

The 1G/2.5G/5G/10G Multi-rate Ethernet PHY Intel® FPGA IP parameter editor allows you to quickly configure your custom IP variation. Use the following steps to specify IP core options and parameters in the Intel® Quartus® Prime Pro Edition software:
  1. In the Intel® Quartus® Prime Pro Edition software, click File > New Project Wizard to create a new Intel® Quartus® Prime project, or File > Open Project to open an existing Intel® Quartus® Prime project. The wizard prompts you to specify a device.
  2. In the IP Catalog (Tools > IP Catalog), locate and double-click 1G/2.5G/5G/10G Multi-rate Ethernet PHY Intel FPGA IP core to customize. The New IP Variant window appears.
  3. Specify a top-level name for your custom IP variation. The parameter editor saves the IP variation settings in a file named <your_ip> .ip.
  4. Click Create. The parameter editor appears.
  5. Specify the parameters for your IP core variation in the parameter editor. Refer to Table 14 for information about specific IP core parameters.
  6. Optionally, to generate a MAC+PHY simulation testbench or compilation and hardware design example, follow the instructions in the F-Tile Low Latency Ethernet 10G MAC Intel® FPGA IP Design Example User Guide.
  7. Click Generate HDL. The Generation dialog box appears.
  8. Specify output file generation options, and then click Generate. The IP variation files generate according to your specifications.
  9. Click Finish. The parameter editor adds the top-level .ip file to the current project automatically. If you are prompted to manually add the .ip file to the project, click Project > Add/Remove Files in Project to add the file.
  10. After generating and instantiating your IP variation, make appropriate pin assignments to connect ports.
Related Information
Level Two Title