F-Tile Low Latency Ethernet 10G MAC Intel® FPGA IP Design Example User Guide

Download PDF
ID 720987
Date 7/08/2024
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. About the F-Tile Low Latency Ethernet 10G MAC Intel® FPGA IP Design Example User Guide 2. Quick Start Guide 3. 10M/100M/1G/2.5G/5G/10G (USXGMII) Ethernet Design Example 4. Interface Signals Description 5. Configuration Registers Description 6. F-Tile Low Latency Ethernet 10G MAC Intel FPGA IP Design Example User Guide Archives 7. Document Revision History for the F-Tile Low Latency Ethernet 10G MAC Intel® FPGA IP Design Example User Guide
2. Quick Start Guide x
2.1. Directory Structure 2.2. Generating the Design 2.3. Compiling and Simulating the Design 2.4. Compiling and Testing the Design in Hardware 2.5. Signal Tap Debugging
2.2. Generating the Design x
2.2.1. Procedure 2.2.2. Design Example Parameters
2.3. Compiling and Simulating the Design x
2.3.1. Procedure 2.3.2. Testbench
2.4. Compiling and Testing the Design in Hardware x
2.4.1. Procedure 2.4.2. Hardware Setup
2.5. Signal Tap Debugging x
2.5.1. Signal Tap Debug Signals
3. 10M/100M/1G/2.5G/5G/10G (USXGMII) Ethernet Design Example x
3.1. Features 3.2. Hardware and Software Requirements 3.3. Functional Description 3.4. Simulation 3.5. Hardware Testing 3.6. Interface Signals 3.7. Configuration Registers
3.3. Functional Description x
3.3.1. Design Components 3.3.2. Clocking Scheme 3.3.3. Reset Scheme
3.3.3. Reset Scheme x
3.3.3.1. Reset Sequence
3.3.3.1. Reset Sequence x
3.3.3.1.1. Run-time Reset Sequence—TX 3.3.3.1.2. Run-time Reset Sequence—RX 3.3.3.1.3. Run-time Reset Sequence—TX + RX
3.4. Simulation x
3.4.1. Test Case—Design Example with the IEEE 1588v2 Feature 3.4.2. Test Case—Design Example without the IEEE 1588v2 Feature
3.5. Hardware Testing x
3.5.1. Test Procedure 3.5.2. Design Constraints
4. Interface Signals Description x
4.1. Clock and Reset Interface Signals 4.2. Avalon® Memory-Mapped Interface Signals 4.3. Avalon® Streaming Interface Signals 4.4. PHY Interface Signals 4.5. Status Interface 4.6. IEEE 1588v2 Timestamp Interface Signals 4.7. Packet Classifier Interface Signals 4.8. TOD Interface Signals
5. Configuration Registers Description x
5.1. Register Access Definition 5.2. Low Latency Ethernet 10G MAC 5.3. PHY 5.4. TOD
5.3. PHY x
5.3.1. 1G/2.5G/5G/10G Multirate PHY
1. About the F-Tile Low Latency Ethernet 10G MAC Intel® FPGA IP Design Example User Guide
2. Quick Start Guide
3. 10M/100M/1G/2.5G/5G/10G (USXGMII) Ethernet Design Example
4. Interface Signals Description
5. Configuration Registers Description
6. F-Tile Low Latency Ethernet 10G MAC Intel FPGA IP Design Example User Guide Archives
7. Document Revision History for the F-Tile Low Latency Ethernet 10G MAC Intel® FPGA IP Design Example User Guide

2.5. Signal Tap Debugging

The IP provides a list of predefined debug signals to capture the behavior of the design example components.
To program the hardware design example on Agilex™ 7 devices:
  1. Click Tools > Signal Tap Logic Analyzer.
  2. Click Hardware Setup and select respective hardware for programming.
  3. Click on Scan Chain to select the proper JTAG.
  4. Click on the SOF Manager to browse and program the SOF.
  5. After the programming is complete, click any of the signals under the Setup window to view the signal behavior.
  6. In the Instance Manager toolbar, click Run Analysis. The signal capture and signal transitions is displayed in the Data window.
  7. Refer to the Signal Tap Logic Analyzer Introduction for more information about Signal Tap.
To start the signal tap debugging:
  1. Generate the design example for the Low Latency Ethernet 10G MAC IP.
  2. Open the .qpf file in the intel_eth_em10g32_0_EXAMPLE_DESIGN/LL10G_10G_USXGMII/ directory.
  3. In the Quartus® Prime Pro Edition software, click File > Open > <LL10G_10G_USXGMII*> > *.stp

Section Content
Signal Tap Debug Signals

Related Information
Level Two Title