F-Tile Low Latency Ethernet 10G MAC Intel® FPGA IP Design Example User Guide

Download PDF
ID 720987
Date 7/08/2024
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. About the F-Tile Low Latency Ethernet 10G MAC Intel® FPGA IP Design Example User Guide 2. Quick Start Guide 3. 10M/100M/1G/2.5G/5G/10G (USXGMII) Ethernet Design Example 4. Interface Signals Description 5. Configuration Registers Description 6. F-Tile Low Latency Ethernet 10G MAC Intel FPGA IP Design Example User Guide Archives 7. Document Revision History for the F-Tile Low Latency Ethernet 10G MAC Intel® FPGA IP Design Example User Guide
2. Quick Start Guide x
2.1. Directory Structure 2.2. Generating the Design 2.3. Compiling and Simulating the Design 2.4. Compiling and Testing the Design in Hardware 2.5. Signal Tap Debugging
2.2. Generating the Design x
2.2.1. Procedure 2.2.2. Design Example Parameters
2.3. Compiling and Simulating the Design x
2.3.1. Procedure 2.3.2. Testbench
2.4. Compiling and Testing the Design in Hardware x
2.4.1. Procedure 2.4.2. Hardware Setup
2.5. Signal Tap Debugging x
2.5.1. Signal Tap Debug Signals
3. 10M/100M/1G/2.5G/5G/10G (USXGMII) Ethernet Design Example x
3.1. Features 3.2. Hardware and Software Requirements 3.3. Functional Description 3.4. Simulation 3.5. Hardware Testing 3.6. Interface Signals 3.7. Configuration Registers
3.3. Functional Description x
3.3.1. Design Components 3.3.2. Clocking Scheme 3.3.3. Reset Scheme
3.3.3. Reset Scheme x
3.3.3.1. Reset Sequence
3.3.3.1. Reset Sequence x
3.3.3.1.1. Run-time Reset Sequence—TX 3.3.3.1.2. Run-time Reset Sequence—RX 3.3.3.1.3. Run-time Reset Sequence—TX + RX
3.4. Simulation x
3.4.1. Test Case—Design Example with the IEEE 1588v2 Feature 3.4.2. Test Case—Design Example without the IEEE 1588v2 Feature
3.5. Hardware Testing x
3.5.1. Test Procedure 3.5.2. Design Constraints
4. Interface Signals Description x
4.1. Clock and Reset Interface Signals 4.2. Avalon® Memory-Mapped Interface Signals 4.3. Avalon® Streaming Interface Signals 4.4. PHY Interface Signals 4.5. Status Interface 4.6. IEEE 1588v2 Timestamp Interface Signals 4.7. Packet Classifier Interface Signals 4.8. TOD Interface Signals
5. Configuration Registers Description x
5.1. Register Access Definition 5.2. Low Latency Ethernet 10G MAC 5.3. PHY 5.4. TOD
5.3. PHY x
5.3.1. 1G/2.5G/5G/10G Multirate PHY Register Map Register Definitions
1. About the F-Tile Low Latency Ethernet 10G MAC Intel® FPGA IP Design Example User Guide
2. Quick Start Guide
3. 10M/100M/1G/2.5G/5G/10G (USXGMII) Ethernet Design Example
4. Interface Signals Description
5. Configuration Registers Description
6. F-Tile Low Latency Ethernet 10G MAC Intel FPGA IP Design Example User Guide Archives
7. Document Revision History for the F-Tile Low Latency Ethernet 10G MAC Intel® FPGA IP Design Example User Guide

5.3.1. 1G/2.5G/5G/10G Multirate PHY

This topic lists the byte offsets of the 1G/2.5G/5G/10G Multirate variant registers for Agilex™ 7 (F-Tile) devices.

Register Map

You can access the 32-bit configuration registers via the Avalon® memory-mapped interface.

Table 25.  Register Map Overview
Address Range Usage Register Width Configuration

0x400 : 0x43F

 USXGMII 32

10M/100M/1G/2.5G/5G/10G (USXGMII)

Register Definitions

Observe the following guidelines when accessing the registers:
  • Do not write to reserved or undefined registers.
  • When writing to the registers, perform read-modify-write operation to ensure that reserved or undefined register bits are not overwritten.
Table 26.  1G/2.5G/5G/10G Multirate PHY Register Definitions
Word Offset Name Description Access HW Reset Value
0x400 usxgmii_control Control Register — —
Bit [0]: USXGMII_ENA:
  • 0: None
  • 1: USXGMII mode
 RW 0
Bit [1]: USXGMII_AN_ENA is used when USXGMII_ENA is set to 1:
  • 0: Disables USXGMII Auto-Negotiation and manually configures the operating speed with the USXGMII_SPEED register.
  • 1: Enables USXGMII Auto-Negotiation, and automatically configures operating speed with link partner ability advertised during USXGMII Auto-Negotiation.
RW 1
Bit [4:2]: USXGMII_SPEED is the operating speed of the PHY in USXGMII mode and USE_USXGMII_AN is set to 0.
  • 3’b000: 10M
  • 3’b001: 100M
  • 3’b010: 1G
  • 3’b011: 10G
  • 3’b100: 2.5G
  • 3’b101: 5G
  • 3’b110: Reserved
  • 3’b111: Reserved
 RW 0
Bit [8:5]: Reserved — —
Bit [9]: RESTART_AUTO_NEGOTIATION

Write 1 to restart Auto-Negotiation sequence The bit is cleared by hardware when Auto-Negotiation is restarted.

 RWC 0
Bit [31:10]: Reserved — —
0x401 usxgmii_status Status Register — —
Bit [1:0]: Reserved — —
Bit [2]: LINK_STATUS indicates link status for USXGMII all speeds
  • 1: Link is established
  • 0: Link synchronization is lost, a 0 is latched
 RO 0
Bit [4:3]: Reserved — —
Bit [5]: AUTO_NEGOTIATION_COMPLETE

A value of 1 indicates the Auto-Negotiation process is completed.

 RO 0
Bit [31:6]: Reserved — —
0x402:0x404 Reserved — — —
0x405 usxgmii_partner_ability Device abilities advertised to the link partner during Auto-Negotiation — —
Bit [6:0]: Reserved — —
Bit [7]: EEE_CLOCK_STOP_CAPABILITY
Indicates whether or not energy efficient Ethernet (EEE) clock stop is supported.
  • 0: Not supported
  • 1: Supported
 RO 0
Bit [8]: EEE_CAPABILITY
Indicates whether or not EEE is supported.
  • 0: Not supported
  • 1: Supported
 RO 0
Bit [11:9]: SPEED
  • 3'b000: 10M
  • 3'b001: 100M
  • 3'b010: 1G
  • 3'b011: 10G
  • 3'b100: 2.5G
  • 3'b101: 5G
  • 3'b110: Reserved
  • 3'b111: Reserved
 RO 0
Bit [12]: DUPLEX
Indicates the duplex mode.
  • 0: Half duplex
  • 1: Full duplex
 RO 0
Bit [13]: Reserved — —
Bit [14]: ACKNOWLEDGE

A value of 1 indicates that the device has received three consecutive matching ability values from its link partner.

 RO 0
Bit [15]: LINK
Indicates the link status.
  • 0: Link down
  • 1: Link up
 RO 0
Bit [31:16]: Reserved — —
0x406:0x411 Reserved — — —
0x412 usxgmii_link_timer

Auto-Negotiation link timer. Sets the link timer value in bit [19:14] from 0 to 2 ms in approximately 0.05-ms steps. You must program the link timer to ensure that it matches the link timer value of the external NBASE-T PHY IP.

The reset value sets the link timer to approximately 1.6 ms.

Bits [13:0] are reserved and always set to 0.

 [19:14]: RW

[13:0]: RO

 [19:14]: 1F

[13:0]: 0
0x413:0x41F Reserved — — —
0x420 ptp_dl Bit [0]: tx_measure_valid
Indicates whether the TX deterministic latency measurement values are valid.
  • 0: Not valid
  • 1: Valid
 RO 0x0
Bit [1]: rx_measure_valid
Indicates whether the RX deterministic latency measurement values are valid.
  • 0: Not valid
  • 1: Valid
 RO 0x0
Bit [2]: tx_dl_reset
TX Deterministic Latency (DL) soft reset. Provides a soft reset to the TX DL block.
  • 0: TX DL block is not under reset
  • 1: TX DL block is being reset
Note: This is not a self-clearing reset.
RW 0x0
Bit [3]: rx_dl_reset
RX Deterministic Latency (DL) soft reset. Provides a soft reset to the RX DL block.
  • 0: RX DL block is not under reset
  • 1: RX DL block is being reset
Note: This is not a self-clearing reset.
RW 0x0
0x421 ptp_dl_tx Bit [20:0]: TX Datapath Latency.
Provides the TX datapath deterministic latency values measured in sampling_clk cycles. Fixed point format Q13.8.
  • Bit [20:8]: The number of clock cycles.
  • Bit [7:0]: The fractional number of clock cycles.

tx_measure_valid (bit 0 of register 0x420) must be asserted before taking the measurement.

RO 0x0
0x422 ptp_dl_rx Bit [20:0]: RX Datapath Latency.
Provides the RX datapath deterministic latency values measured in sampling_clk cycles. Fixed point format Q13.8.
  • Bit [20:8]: The number of clock cycles.
  • Bit [7:0]: The fractional number of clock cycles.

rx_measure_valid (bit 0 of register 0x420) must be asserted before taking the measurement.

RO 0x0
Related Information
Level Two Title