E-tile Hard IP Intel® Agilex™ Design Example User Guide: Ethernet, E-tile CPRI PHY and Dynamic Reconfiguration

ID 683860
Date 8/04/2021
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents

2.3.1.3. E-tile Ethernet IP for Intel Agilex FPGA 100GE PCS Only with Optional RS-FEC Simulation Design Example

The simulation block diagram below is generated using the following settings in the IP parameter editor:
  1. Under the IP tab:
    1. Single 100GE with optional RSFEC or 100GE or 1 to 4 channel 10GE/25GE with optional RSFEC and PTP as the core variant.
    2. 100GE Channel as Active channel(s) at startup if you choose 100GE or 1 to 4 channel 10GE/25GE with optional RSFEC and PTP as the core variant.
  2. Under the 100GE tab:
    1. 100G as the Ethernet rate.
    2. PCS_Only, PCS+(528,514)RSFEC, or PCS+(544,514)RSFEC as the Ethernet IP layer.
Figure 15. Simulation Block Diagram for E-tile Ethernet IP for Intel Agilex FPGA 100GE PCS Only Design Example

The testbench sends traffic through the IP core, exercising the transmit side and receive side of the IP core.

To speed up simulation, the IP core simulation model sends alignment marker tags at shorter intervals than required by the IEEE Ethernet standard. The standard specifies an alignment marker interval of 16,384 words in each virtual lane. The simulation model with the testbench implements an alignment marker interval of 512 words.

The successful test run displays output confirming the following behavior:

  1. The client logic resets the IP core.
  2. Waits for RX datapath to align.
  3. Once alignment is complete, client logic transmits a series of packets to the IP core through TX MII interface.
  4. A counter drives i_tx_mii_am port with alignment marker insertion requests at the correct intervals.
  5. The client logic receives the same series of packets through RX MII interface.
  6. The client logic then checks the number of packets received.
  7. Displaying Testbench complete.

The following sample output illustrates a successful simulation test run for a 100GE, PCS only IP core variation.

o_tx_lanes_stable is 1 at time             354775000
waiting for tx_dll_lock....
TX DLL LOCK is 1 at time             413726943
waiting for tx_transfer_ready....
TX transfer ready is 1 at time             414046815
waiting for rx_transfer_ready....
RX transfer ready is 1 at time             425122383
EHIP PLD Ready out is 1 at time             425184000
EHIP reset out is 0 at time             425320000
EHIP reset ack is 0 at time             426016853
EHIP TX reset out is 0 at time             426232000
EHIP TX reset ack is 0 at time             476830347
waiting for EHIP Ready....
EHIP READY is 1 at time             476910363
EHIP RX reset out is 0 at time             478680000
waiting for rx reset ack....
EHIP RX reset ack is 0 at time             478777403
Waiting for RX Block Lock
EHIP Rx Block Lock  is high at time             481444603
Waiting for AM lock
EHIP Rx am Lock  is high at time             482711523
Waiting for RX alignment
RX deskew locked
RX lane aligmnent locked
Sending Packets and Receiving Packets
====> writedata = 00000001 

====>MATCH!     ReaddataValid = 1 Readdata = 00000053 Expected_Readdata = 00000053 

**
** Testbench complete.
**
*****************************************