E-tile Hard IP Intel® Agilex™ Design Example User Guide: Ethernet, E-tile CPRI PHY and Dynamic Reconfiguration

ID 683860
Date 8/04/2021
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents

2.3.2.2. 100GE MAC+PCS with Optional RS-FEC and PTP Hardware Design Example

Figure 19. 100GE MAC + PCS with Optional RS-FEC and PTP Hardware Design Examples High Level Block Diagram
The E-tile Ethernet IP for Intel Agilex FPGA hardware design example includes the following components:
  • E-tile Ethernet IP for Intel Agilex FPGA core.
  • Client logic that coordinates the programming of the IP core and packet generation.
  • Time-of-day (ToD) module to provide a continuous flow of current time-of-day information to the IP core.
  • PIO block to store RX and TX PTP timestamp for accuracy calculation and to send PTP 2-step timestamp request.
  • Avalon® memory-mapped interface address decoder to decode reconfiguration address space for MAC, transceiver, and RS-FEC modules during reconfiguration accesses.
  • JTAG controller that communicates with the System Console. You communicate with the client logic through the System Console.

The following sample output illustrates a successful hardware test run for a 100GE, MAC+PCS with RS-FEC, non-PTP IP core variation. The test results are located at <design_example_dir>/hardware_test_design/hwtest_ptp/c3_elane_xcvr_loopback_test.log or <design_example_dir>/hardware_test_design/hwtest_ptp/c3_elane_traffic_basic_test.log.

Result from c3_elane_xcvr_loopback_test.log file:

Info: Set JTAG Master Service Path


Info: Opened JTAG Master Service

	Test Start time is: 13:25:08
	Test Start date is: 03/04/2019


Info: Cycling reset ...
	Successfully Write Channel 0 XCVR CSR Register offset = 0x84, data = 0x1 
.
.
.
	Successfully Read  Channel 0 XCVR CSR Register offset = 0x88, data = 0x8 

	C3 EHIP XCVR Channel 0 Loopback mode is successfully enabled 

	Successfully Write Channel 1 XCVR CSR Register offset = 0x84, data = 0x1 
.
.
.
	Successfully Read  Channel 1 XCVR CSR Register offset = 0x88, data = 0x8 

	C3 EHIP XCVR Channel 1 Loopback mode is successfully enabled 
.
.
.
	Successfully Read  Channel 2 XCVR CSR Register offset = 0x88, data = 0x8 

	C3 EHIP XCVR Channel 2 Loopback mode is successfully enabled 

	Successfully Write Channel 3 XCVR CSR Register offset = 0x84, data = 0x1 
.
.
.
	Successfully Write Channel 3 XCVR CSR Register offset = 0x8a, data = 0x80 
	Successfully Read  Channel 3 XCVR CSR Register offset = 0x88, data = 0x8 

	C3 EHIP XCVR Channel 3 Loopback mode is successfully enabled 

	Successfully Write EHIP User Register phy_ehip_csr_soft_reset               , offset = 0x310, data = 0x0 
.
.
.
	Successfully Read  EHIP User Register phy_ehip_csr_soft_reset               , offset = 0x310, data = 0x0 

	C3 EHIP System Reset is successfully 

	Test End time is: 13:25:09
	Test End date is: 03/04/2019

Info: Closed JTAG Master Service


Info: Test <c3_ehip_xcvr_loopback_test> Passed
Result from c3_elane_traffic_basic_test_log file:
Info: Set JTAG Master Service Path


Info: Opened JTAG Master Service

	Test Start time is: 13:25:09
	Test Start date is: 03/04/2019


Info: Read all EHIP CSR registers

	Successfully Read  EHIP User Register phy_revid                              , offset = 0x300, data = 0x11112015 
	Successfully Read  EHIP User Register phy_scratch                           , offset = 0x301, data = 0x0 
.
.
.
	Successfully Read  EHIP User Register phy_ehip_csr_soft_reset               , offset = 0x310, data = 0x0 

	C3 EHIP System Reset is successfully 


Info: Stopping the traffic generator

	Successfully Write EHIP Traffic GEN/CHK Register, offset = 0x10, data = 0x87 

Info: clearing the statistics

	Successfully Write EHIP User Register cntr_tx_config                        , offset = 0x845, data = 0x1 
	Successfully Write EHIP User Register cntr_rx_config                        , offset = 0x945, data = 0x1 

Info: Enabling the statistics

	Successfully Write EHIP User Register cntr_tx_config                        , offset = 0x845, data = 0x0 
	Successfully Write EHIP User Register cntr_rx_config                        , offset = 0x945, data = 0x0 

Info: Starting the traffic generator

	Successfully Write EHIP Traffic GEN/CHK Register, offset = 0x10, data = 0x85 
	Successfully Read  EHIP User Register cntr_tx_fragments_lo                  , offset = 0x800, data = 0x0 

Info: Stopping the traffic generator

	Successfully Write EHIP Traffic GEN/CHK Register, offset = 0x10, data = 0x87 
	Successfully Read  EHIP Traffic GEN/CHK Register, offset = 0x10, data = 0x87 
.
.
.
	Successfully Read  EHIP User Register cntr_rx_badlt_hi                      , offset = 0x969, data = 0x0 

Info: Test iteration 1 is completed 

	Successfully Read  RSFEC Register rsfec_top_rx_cfg                     , offset = 0x14, data = 0x1111 
	Successfully Read  RSFEC Register arbiter_base_cfg                      , offset = 0x0, data = 0x1 
	Successfully Read  RSFEC Register rsfec_top_clk_cfg                    , offset = 0x4, data = 0xf00 
	Successfully Read  RSFEC Register rsfec_top_tx_cfg                     , offset = 0x10, data = 0x0 
	Successfully Write RSFEC Register rsfec_top_tx_cfg                     , offset = 0x10, data = 0x10001666 
	Successfully Read  RSFEC Register rsfec_top_tx_cfg                     , offset = 0x10, data = 0x10001666 
	Successfully Write RSFEC Register rsfec_top_tx_cfg                     , offset = 0x10, data = 0x0 
	Successfully Read  RSFEC Register rsfec_top_tx_cfg                     , offset = 0x10, data = 0x0 

	Test End time is: 13:25:21
	Test End date is: 03/04/2019

Info: Closed JTAG Master Service


Info: Test <c3_ehip_traffic_basic_test> Passed
The following sample output illustrates a successful hardware test run for a 100GE, MAC+PCS with RS-FEC, PTP IP core variation. The test result is located at <design_example_dir>/hardware_test_design/hwtest_ptp/c3_elane_ptp_traffic_basic_test.log.
Info: Set JTAG Master Service Path


Info: Opened JTAG Master Service

	Test Start time is: 13:25:21
	Test Start date is: 03/04/2019

	Successfully Write EHIP User Register phy_ehip_csr_soft_reset               , offset = 0x310, data = 0x0 
	Successfully Write EHIP User Register phy_ehip_csr_soft_reset               , offset = 0x310, data = 0x1 
.
.
.
	Successfully Read  EHIP User Register phy_ehip_csr_soft_reset               , offset = 0x310, data = 0x0 

	C3 EHIP System Reset is successfully 

	Successfully Write Channel 0 XCVR CSR Register offset = 0x84, data = 0x0 
	Successfully Write Channel 0 XCVR CSR Register offset = 0x85, data = 0x0 
.
.
.
	Successfully Write Channel 3 XCVR CSR Register offset = 0x93, data = 0x0 
Internal Loopback iCal Status
	Successfully Write Channel 0 XCVR CSR Register offset = 0x84, data = 0x0 
.
.
.
	Successfully Write Channel 0 XCVR CSR Register offset = 0x93, data = 0x0 
iCal is done successfully on channel 0
	Successfully Write Channel 1 XCVR CSR Register offset = 0x84, data = 0x0 
.
.
. 

	Successfully Write Channel 3 XCVR CSR Register offset = 0x93, data = 0x0 

Info: Cycling reset ...
	Successfully Write EHIP Traffic GEN/CHK Register, offset = 0x8, data = 0x40 
	Successfully Write EHIP Traffic GEN/CHK Register, offset = 0x9, data = 0x1 
	Successfully Read  EHIP Traffic GEN/CHK Register, offset = 0x9, data = 0x1 

Info: clearing the statistics

	Successfully Write EHIP User Register cntr_tx_config                        , offset = 0x845, data = 0x1 
	Successfully Write EHIP User Register cntr_rx_config                        , offset = 0x945, data = 0x1 

Info: Enabling the statistics

	Successfully Write EHIP User Register cntr_tx_config                        , offset = 0x845, data = 0x0 
	Successfully Write EHIP User Register cntr_rx_config                        , offset = 0x945, data = 0x0 

Info: Accuracy measurement settings

Info: UI Value = 0x0009EE01 

Info: TX Extra Latency = 0xc69814 

Info: RX Extra Latency = 0x5467088 

	Successfully Write EHIP User Register tx_ptp_extra_latency                  , offset = 0xa0a, data = 0xc698 
	Successfully Read  EHIP User Register tx_ptp_extra_latency                  , offset = 0xa0a, data = 0xc698 
	Successfully Write EHIP User Register rx_ptp_extra_latency                  , offset = 0xb06, data = 0x80054670 
	Successfully Read  EHIP User Register rx_ptp_extra_latency                  , offset = 0xb06, data = 0x80054670 

Info: Waiting for VL offset data ready

	Successfully Read  EHIP Soft PTP Register vl_offset_data0_lo                    , offset = 0xc10, data = 0xc000008c 

Info: All VL data reading, calculation of VL offset and reloading new VL offset...

Reading FEC lane mapping and deskew ...
Lane map 0 = 0
Lane map 1 = 1
Lane map 2 = 2
Lane map 3 = 3
Lane 0 skew = 1
Lane 1 skew = 2
Lane 2 skew = 1
Lane 3 skew = 2

++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
gen_vl_data_fec: Input Deskew_delay = 0x00000001
gen_vl_data_fec: Input Selected_pl  = 0
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

============================================================================================

before-rotation: VL[PL] 0[0], deskew_delay = 0x1 UI, vl_offset_bits = 1
After Rotation: calc_vl_offset done - RVL 4, LPL 0, LVL 0 Sign=0, NS=0, FNS=2542


For LOCAL_VL=0 --> CALC_VL_OFFSET=0x000009EE, LOCAL_PL=0, REMOTE_VL=4
Final Calculated value - 325380

============================================================================================
.
.
.
============================================================================================

before-rotation: VL[PL] 19[0], deskew_delay = 0x1 UI, vl_offset_bits = 5
before-rotation: VL[PL] 19[0], deskew_delay = 0x1 UI, vl_offset_bits_shifted = -325
After Rotation: calc_vl_offset done - RVL 3, LPL 0, LVL 19 Sign=1, NS=12, FNS=39719


For LOCAL_VL=19 --> CALC_VL_OFFSET=0x800C9B27, LOCAL_PL=0, REMOTE_VL=3
Final Calculated value - 274983654275

============================================================================================


	
Writing new VL offsets ...
write_vl_offset Loading vls data.....
	Successfully Write EHIP Soft PTP Register vl_offset0_lo                         , offset = 0xc40, data = 0x4 
.
.
.
	Successfully Write EHIP Soft PTP Register vl_offset19_hi                        , offset = 0xc67, data = 0x800c9b27 

Info: Waiting for PTP RX ready...

	Successfully Read  EHIP PIO Register, offset = 0x0, data = 0x7 
.
.
.
	Successfully Read  EHIP PIO Register, offset = 0xc, data = 0x101 

Info: Iteration = 1 : TX Timestamp = 0000000000060ca82f0f8fa7,  RX Timestamp = 0000000000060ca82f0e78eb,  Accuracy Difference = -1.08880615 ns 

	Successfully Write EHIP PIO Register, offset = 0xc, data = 0x0 
	Successfully Write EHIP Traffic GEN/CHK Register, offset = 0x10, data = 0x57 
	Successfully Write EHIP PIO Register, offset = 0xc, data = 0x102 
	Successfully Write EHIP Traffic GEN/CHK Register, offset = 0x10, data = 0x55 
	Successfully Read  EHIP User Register cntr_tx_64b_lo                        , offset = 0x816, data = 0x2 
	Successfully Read  EHIP User Register cntr_rx_64b_lo                        , offset = 0x916, data = 0x2 
	Successfully Read  EHIP PIO Register, offset = 0x4, data = 0x90e52f43 
	Successfully Read  EHIP PIO Register, offset = 0x5, data = 0x60f25 
	Successfully Read  EHIP PIO Register, offset = 0x6, data = 0x0 
	Successfully Read  EHIP PIO Register, offset = 0x8, data = 0x90e68e57 
	Successfully Read  EHIP PIO Register, offset = 0x9, data = 0x60f25 
	Successfully Read  EHIP PIO Register, offset = 0xa, data = 0x0 
	Successfully Read  EHIP PIO Register, offset = 0x7, data = 0x2 
	Successfully Read  EHIP PIO Register, offset = 0xc, data = 0x102 

.
.
.

Info: Iteration = 100 : TX Timestamp = 00000000000a1d8d0ad81ed6,  RX Timestamp = 00000000000a1d8d0ad982d9,  Accuracy Difference = 1.39067078 ns 


Info: Stopping the traffic generator

	Successfully Write EHIP PIO Register, offset = 0xc, data = 0x0 
.
.
.
	Successfully Read  EHIP User Register cntr_rx_badlt_hi                      , offset = 0x969, data = 0x0 

	Test End time is: 13:25:39
	Test End date is: 03/04/2019

Info: Closed JTAG Master Service



Info: Test <c3_ehip_ptp_traffic_basic_test> Passed