GTS Serial Lite IV IP User Guide

Download PDF
ID 813966
Date 10/24/2025
Public
Document Table of Contents
Document Table of Contents x
1. About the GTS Serial Lite IV IP User Guide: Agilex™ 5 E-Series/D-Series and Agilex™ 3 Devices 2. GTS Serial Lite IV IP Overview 3. Getting Started 4. Functional Description 5. Parameters 6. GTS Serial Lite IV IP Interface Signals 7. Designing with GTS Serial Lite IV IP 8. Document Revision History for the GTS Serial Lite IV IP User Guide
2. GTS Serial Lite IV IP Overview x
2.1. Release Information 2.2. Supported Features 2.3. IP Version Support Level 2.4. Device Speed Grade Support 2.5. Resource Utilization and Latency 2.6. Bandwidth Efficiency
3. Getting Started x
3.1. Installing and Licensing IP Cores 3.2. Specifying the IP Parameters and Options 3.3. Generated File Structure 3.4. Simulating IP Cores 3.5. Synthesizing IP Cores in Other EDA Tools 3.6. Compiling the Full Design
3.1. Installing and Licensing IP Cores x
3.1.1. IP Evaluation Mode
3.4. Simulating IP Cores x
3.4.1. Simulating and Verifying the Design
4. Functional Description x
4.1. TX Datapath 4.2. RX Datapath 4.3. GTS Serial Lite IV IP Clock Architecture 4.4. Reset and Link Initialization 4.5. Link Rate and Bandwidth Efficiency Calculation
4.1. TX Datapath x
4.1.1. TX MAC Adapter 4.1.2. Control Word (CW) Insertion 4.1.3. TX CRC 4.1.4. TX MII Encoder 4.1.5. TX PCS and PMA
4.1.2. Control Word (CW) Insertion x
4.1.2.1. Start-of-burst CW 4.1.2.2. End-of-burst CW 4.1.2.3. Alignment Paired CW 4.1.2.4. Empty-cycle CW 4.1.2.5. Idle CW 4.1.2.6. Data Word
4.2. RX Datapath x
4.2.1. RX PCS and PMA 4.2.2. RX MII Decoder 4.2.3. RX CRC 4.2.4. RX Deskew 4.2.5. RX CW Removal
4.4. Reset and Link Initialization x
4.4.1. TX Reset and Initialization Sequence 4.4.2. RX Reset and Initialization Sequence
6. GTS Serial Lite IV IP Interface Signals x
6.1. Clock Signals 6.2. Reset Signals 6.3. MAC Signals 6.4. Transceiver Reconfiguration Signals 6.5. PMA/PCS Signals
7. Designing with GTS Serial Lite IV IP x
7.1. Reset Guidelines 7.2. Error Handling Guidelines 7.3. Analog Parameter Settings
1. About the GTS Serial Lite IV IP User Guide: Agilex™ 5 E-Series/D-Series and Agilex™ 3 Devices
2. GTS Serial Lite IV IP Overview
3. Getting Started
4. Functional Description
5. Parameters
6. GTS Serial Lite IV IP Interface Signals
7. Designing with GTS Serial Lite IV IP
8. Document Revision History for the GTS Serial Lite IV IP User Guide

4.1.2.1. Start-of-burst CW

Figure 11. Start-of-burst CW Format
In Full mode, you can insert the START CW by asserting the tx_avs_startofpacket signal. When you assert only the tx_avs_startofpacket signal, the sop bit is set. When you assert both the tx_avs_startofpacket and tx_avs_endofpacket signals, the seop bit is set.
Table 12.   START CW Field Values
Field Value
sop/seop 1
usr 8 Depending on the tx_is_usr_cmd signal:
  • 1: When tx_is_usr_cmd = 1
  • 0: When tx_is_usr_cmd = 0
align 0

In Basic mode, the MAC sends a START CW after the reset is deasserted. If no data is available, the MAC continuously sends EMPTY_CYC paired with END and START CWs until you start sending data.

8 This is supported only in Full mode.
Level Two Title