F-Tile Interlaken Intel® FPGA IP User Guide

Download PDF
ID 683622
Date 3/28/2022
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. About the F-Tile Interlaken Intel® FPGA IP Core 2. Getting Started 3. Parameter Settings 4. Functional Description 5. Interface Signals 6. IP Registers 7. F-Tile Interlaken Intel® FPGA IP User Guide Archives 8. Document Revision History for F-Tile Interlaken Intel® FPGA IP User Guide
1. About the F-Tile Interlaken Intel® FPGA IP Core x
1.1. Features 1.2. Device Family Support 1.3. Performance and Resource Utilization 1.4. Round-trip Latency 1.5. Release Information
2. Getting Started x
2.1. Installing and Licensing Intel® FPGA IP Cores 2.2. Generated File Structure 2.3. Specifying the IP Core Parameters and Options 2.4. Reference and System PLL Clock for your IP Design 2.5. Simulating the IP Core 2.6. Compiling the Full Design and Programming the FPGA
2.1. Installing and Licensing Intel® FPGA IP Cores x
2.1.1. Intel® FPGA IP Evaluation Mode
2.4. Reference and System PLL Clock for your IP Design x
2.4.1. System PLL Configuration
4. Functional Description x
4.1. Data Path Flow 4.2. Interlaken Look-aside Data Path Flow 4.3. Modes of Operation 4.4. Performance 4.5. IP Reset 4.6. M20K ECC Support 4.7. Out-of-Band Flow Control
4.1. Data Path Flow x
4.1.1. Interlaken TX Path 4.1.2. Interlaken RX Path
4.1.1. Interlaken TX Path x
4.1.1.1. Transmit Path Blocks 4.1.1.2. In-Band Calendar Bits on Transmit Side
4.1.2. Interlaken RX Path x
4.1.2.1. Receive Path Blocks 4.1.2.2. In-Band Calendar Bits on Receive Side 4.1.2.3. RX Errored Packet Handling
4.1.2.3. RX Errored Packet Handling x
4.1.2.3.1. Example With Errors and In-Band Calendar Bits
4.2. Interlaken Look-aside Data Path Flow x
4.2.1. Interlaken Look-aside TX Path 4.2.2. Interlaken Look-aside RX Path
4.2.1. Interlaken Look-aside TX Path x
4.2.1.1. Transmit Path Blocks
4.2.2. Interlaken Look-aside RX Path x
4.2.2.1. Receive Path Blocks 4.2.2.2. RX Error Handling
4.3. Modes of Operation x
4.3.1. Interleaved and Packet Modes 4.3.2. Multi-Segment Mode 4.3.3. Interlaken Look-aside Mode
4.3.1. Interleaved and Packet Modes x
4.3.1.1. Transmit User Data Interface Examples 4.3.1.2. Receive User Data Interface Example
4.3.2. Multi-Segment Mode x
4.3.2.1. Multi-Segment Interface Example
4.3.3. Interlaken Look-aside Mode x
4.3.3.1. Transmit User Data Interface Example 4.3.3.2. Receive User Data Interface Examples
5. Interface Signals x
5.1. Clock and Reset Interface Signals 5.2. Transmit User Interface Signals 5.3. Receive User Interface Signals 5.4. Management Interface Signals 5.5. Reconfiguration Interface Signals 5.6. Interlaken Link and Miscellaneous Signals
1. About the F-Tile Interlaken Intel® FPGA IP Core
2. Getting Started
3. Parameter Settings
4. Functional Description
5. Interface Signals
6. IP Registers
7. F-Tile Interlaken Intel® FPGA IP User Guide Archives
8. Document Revision History for F-Tile Interlaken Intel® FPGA IP User Guide

2.4. Reference and System PLL Clock for your IP Design

Each F-tile system must instantiate one F-Tile Reference and System PLL Clocks Intel FPGA IP. The F-Tile Reference and System PLL Clocks Intel FPGA IP performs three main functions:
  1. Configure reference clock for FHT PMA:
    • Enable the FHT common PLLs and select the reference clock source for FHT common PLL
    • Specify the FHT reference clock source frequency
  2. Configure reference clock for FGT PMA:
    • Enable FGT reference clocks and specify the reference clock frequency
    • Specify FGT CDR output
  3. Configure system PLL:
    • Enable system PLL and specify its mode
    • Specify the reference clock source and frequency for system PLL
Note: In your IP design, you must include an F-Tile Reference and System PLL Clocks Intel FPGA IP core to pass logic generation flow.

The F-Tile Reference and System PLL Clocks Intel FPGA IP must always connect to a protocol based Intel FPGA IP. The F-Tile Reference and System PLL Clocks Intel FPGA IP cannot be compiled or simulated as a standalone IP. For more information on parameters and port list for F-Tile Reference and System PLL Clocks Intel FPGA IP core, refer to the F-tile Architecture and PMA/FEC Direct PHY IP User Guide.

When you design multiple interfaces or protocol-based IP cores within a single F-tile, you must use only one instance of the F-Tile Reference and System PLL Clocks Intel FPGA IP core to configure:
  • All required reference clocks for FGT PMA (up to 10) and FHT PMA (up to 2) to implement multiple interfaces within a single F-tile.
  • All required FHT common PLLs (up to 2) to implement multiple interfaces within a single F-tile.
  • All required System PLLs (up to 3) to implement multiple interfaces within a single F-tile.
  • All required reference clocks for system PLLs (up to 8 – shared with FGT PMA) to implement multiple interfaces within a single F-tile.

When you design multiple interfaces or protocol-based IP cores within a single F-tile, you can only use three System PLLs. For example, you can use one System PLL for PCIe and two for Ethernet and other protocols. However, there are other use cases where you can use all three for various interfaces within the Ethernet and PMA-Direct digital blocks. As there are only three System PLLs, multiple interfaces or protocol-based IP cores with different line rates may have to share a System PLL. While sharing a System PLL, the interface with the highest line rate determines the system PLL frequency, and the interfaces with the lower line rates must be overclocked. For more information, refer to the F-tile Architecture and PMA/FEC Direct PHY IP User Guide.


Section Content
System PLL Configuration

Related Information
Level Two Title