Intel® Quartus® Prime Timing Analyzer Cookbook

ID 683081
Date 11/12/2018
Public

A newer version of this document is available. Customers should click here to go to the newest version.

JTAG Signals

Many in-system debugging tools use the JTAG interface in Intel FPGAs.

When you debug your design with the JTAG interface, the JTAG signals TCK, TMS, TDI, and TDO are implemented as part of the design. Because of this, the Timing Analyzer flags these signals as unconstrained when an unconstrained path report is generated.

Table 1.  JTAG Signals That Might Appear as Unconstrained
Signal Name Description
altera_reserved_tck 1 2 JTAG test clock input port
altera_reserved_tms 2 JTAG test mode select input port
altera_reserved_tdi 2 JTAG test data input line input port
altera_reserved_tdo 2 JTAG test data output line output port

You can constrain the JTAG signals by applying the following SDC commands:

JTAG Signal Constraints

# Search "---customize here---" for the few decisions you need to make 
#
# By default, the most challenging timing spec is applied to work in 
# many JTAG chain setup situations

set_time_format -unit ns -decimal_places 3

# This is the main entry point called at the end of this SDC file.
proc set_jtag_timing_constraints { } {
    # If the timing characteristic outside of FPGA is well understood, and 
    # there is a need to provide more slack to allow flexible placement of 
    # JTAG logic in the FPGA core, use the timing constraints for both 
    # timing analysis and fitter; otherwise, use the default fitter timing
    # constraints.

    # ---customize here---
    set use_fitter_specific_constraint 1

    if { $use_fitter_specific_constraint && [string equal quartus_fit $::TimeQuestInfo(nameofexecutable)] } {
        # Define a different set of timing spec to influence place-and-route 
        # result in the jtag clock domain. The slacks outside of FPGA are 
        # maximized.

        set_default_quartus_fit_timing_directive
    }  else {
        # Define a set of timing constraints that describe the JTAG paths 
        # for the Timing Analyzer to analyze. The Timing Analyzer timing reports show whether 
        # the JTAG logic in the FPGA core will operates in this setup.

        set_jtag_timing_spec_for_timing_analysis
    }
}

proc set_default_quartus_fit_timing_directive { } {
    # A10 supports max 33.3Mhz clock
    set jtag_33Mhz_t_period 30

    create_clock -name {altera_reserved_tck} -period $jtag_33Mhz_t_period [get_ports {altera_reserved_tck}] 
    set_clock_groups -asynchronous -group {altera_reserved_tck} 
    # Force fitter to place register driving TDO pin to be as close to 
    # the JTAG controller as possible to maximize the slack outside of FPGA.
    set_max_delay -to [get_ports { altera_reserved_tdo } ] 0 
}

proc set_jtag_timing_spec_for_timing_analysis { } {
derive_clock_uncertainty

    # There are few possible JTAG chain configurations:
    # a. This device is the only device in the JTAG chain
    # b. This device is the first one in the JTAG chain
    # c. This device is in the middle of the JTAG chain
    # d. This device is the last one in the JTAG chain

    # No matter where the device is in the chain. The tck and tms are driven
    # directly from JTAG hardware.
    set_tck_timing_spec
    set_tms_timing_spec

    # Depending on where the device is located along the chain, tdi can be 
    # either driven by blaster hw (a. b.) or driven by another device in the 
    # chain(c. d.)
    # ---customize here---
    set tdi_is_driven_by_blaster 1

    if { $tdi_is_driven_by_blaster } {
    set_tdi_timing_spec_when_driven_by_blaster
    } else {
    set_tdi_timing_spec_when_driven_by_device
    }

    # Depending on where the device is located along the chain, tdo can  
    # drive either blaster hw (a. d.) or another device in the chain (b. c.)
    # ---customize here---
    set tdo_drive_blaster 1

    if { $tdo_drive_blaster } {
        set_tdo_timing_spec_when_drive_blaster
    } else {
        set_tdo_timing_spec_when_drive_device
    }

    set_optional_ntrst_timing_spec

    # Cut a few timing paths that are not related to JTAG logic in 
    # the FPGA core, such as security mode.
    set_false_path -from [get_ports {altera_reserved_tdi}] -to [get_ports {altera_reserved_tdo}]
    if { [get_collection_size [get_registers -nowarn *~jtag_reg]] > 0 } {
        set_false_path -from [get_registers *~jtag_reg] -to [get_ports {altera_reserved_tdo}]
    }

}

proc set_tck_timing_spec { } {
    # USB Blaster 1 uses 6 MHz clock = 166.666 ns period
    set ub1_t_period 166.666
    # USB Blaster 2 uses 24 MHz clock = 41.666 ns period
    set ub2_default_t_period 41.666
    # USB Blaster 2 running at 16 MHz clock safe mode = 62.5 ns period
    set ub2_safe_t_period 62.5

    # ---customize here---
    set tck_t_period $ub2_default_t_period

    create_clock -name {altera_reserved_tck} -period $tck_t_period  [get_ports {altera_reserved_tck}]
    set_clock_groups -asynchronous -group {altera_reserved_tck}
}

proc get_tck_delay_max { } {
    set tck_blaster_tco_max 14.603
    set tck_cable_max 11.627

    # tck delay on the PCB depends on the trace length from JTAG 10-pin 
    # header to FPGA on board. In general on the PCB, the signal travels 
    # at the speed of ~160 ps/inch (1000 mils = 1 inch).
    # ---customize here---
    set tck_header_trace_max 0.5

    return [expr $tck_blaster_tco_max + $tck_cable_max + $tck_header_trace_max]
}

proc get_tck_delay_min { } {
    set tck_blaster_tco_min 14.603
    set tck_cable_min 10.00

    # tck delay on the PCB depends on the trace length from JTAG 10-pin 
    # header to FPGA on board. In general on the PCB, the signal travels 
    # at the speed of ~160 ps/inch (1000 mils = 1 inch).
    # ---customize here---
    set tck_header_trace_min 0.1

    return [expr $tck_blaster_tco_min + $tck_cable_min + $tck_header_trace_min]
}

proc set_tms_timing_spec { } {
    set tms_blaster_tco_max 9.468
    set tms_blaster_tco_min 9.468

    set tms_cable_max 11.627
    set tms_cable_min 10.0

    # tms delay on the PCB depends on the trace length from JTAG 10-pin 
    # header to FPGA on board. In general on the PCB, the signal travels 
    # at the speed of ~160 ps/inch (1000 mils = 1 inch).
    # ---customize here---
    set tms_header_trace_max 0.5
    set tms_header_trace_min 0.1

    set tms_in_max [expr $tms_cable_max + $tms_header_trace_max + $tms_blaster_tco_max - [get_tck_delay_min]]
    set tms_in_min [expr $tms_cable_min + $tms_header_trace_min + $tms_blaster_tco_min - [get_tck_delay_max]]

    set_input_delay -add_delay -clock_fall -clock altera_reserved_tck -max $tms_in_max [get_ports {altera_reserved_tms}]
    set_input_delay -add_delay -clock_fall -clock altera_reserved_tck -min $tms_in_min [get_ports {altera_reserved_tms}]
}

proc set_tdi_timing_spec_when_driven_by_blaster { } {
    set tdi_blaster_tco_max 8.551
    set tdi_blaster_tco_min 8.551

    set tdi_cable_max 11.627
    set tdi_cable_min 10.0

    # tms delay on the PCB depends on the trace length from JTAG 10-pin 
    # header to FPGA on board. In general on the PCB, the signal travels 
    # at the speed of ~160 ps/inch (1000 mils = 1 inch).
    # ---customize here---
    set tdi_header_trace_max 0.5
    set tdi_header_trace_min 0.1

    set tdi_in_max [expr $tdi_cable_max + $tdi_header_trace_max + $tdi_blaster_tco_max - [get_tck_delay_min]]
    set tdi_in_min [expr $tdi_cable_min + $tdi_header_trace_min + $tdi_blaster_tco_min - [get_tck_delay_max]]

    #TDI launches at the falling edge of TCK per standard
    set_input_delay -add_delay -clock_fall -clock altera_reserved_tck -max $tdi_in_max [get_ports {altera_reserved_tdi}]
    set_input_delay -add_delay -clock_fall -clock altera_reserved_tck -min $tdi_in_min [get_ports {altera_reserved_tdi}]
}

proc set_tdi_timing_spec_when_driven_by_device { } {
    # TCO timing spec of tdo on the device driving this tdi input
    # ---customize here---
    set previous_device_tdo_tco_max 10.0
    set previous_device_tdo_tco_min 10.0

    # tdi delay on the PCB depends on the trace length from JTAG 10-pin 
    # header to FPGA on board. In general on the PCB, the signal travels 
    # at the speed of ~160 ps/inch (1000 mils = 1 inch).
    # ---customize here---
    set tdi_trace_max 0.5
    set tdi_trace_min 0.1

    set tdi_in_max [expr $previous_device_tdo_tco_max + $tdi_trace_max - [get_tck_delay_min]]
    set tdi_in_min [expr $previous_device_tdo_tco_min + $tdi_trace_min - [get_tck_delay_max]]

    #TDI launches at the falling edge of TCK per standard
    set_input_delay -add_delay -clock_fall -clock altera_reserved_tck -max $tdi_in_max [get_ports {altera_reserved_tdi}]
    set_input_delay -add_delay -clock_fall -clock altera_reserved_tck -min $tdi_in_min [get_ports {altera_reserved_tdi}]
}

proc set_tdo_timing_spec_when_drive_blaster { } {
    set tdo_blaster_tsu 5.831
    set tdo_blaster_th -1.651

    set tdo_cable_max 11.627
    set tdo_cable_min 10.0

    # tdi delay on the PCB depends on the trace length from JTAG 10-pin 
    # header to FPGA on board. In general on the PCB, the signal travels 
    # at the speed of ~160 ps/inch (1000 mils = 1 inch).
    # ---customize here---
    set tdo_header_trace_max 0.5
    set tdo_header_trace_min 0.1

    set tdo_out_max [expr $tdo_cable_max + $tdo_header_trace_max + $tdo_blaster_tsu + [get_tck_delay_max]]
    set tdo_out_min [expr $tdo_cable_min + $tdo_header_trace_min - $tdo_blaster_th + [get_tck_delay_min]]

    #TDO does not latch inside the USB Blaster II at the rising edge of TCK, 
    # it actually is latched one half cycle later in packed mode 
    # (equivalent to 1 JTAG fall-to-fall cycles)
    set_output_delay -add_delay -clock_fall -clock altera_reserved_tck -max $tdo_out_max [get_ports {altera_reserved_tdo}]
    set_output_delay -add_delay -clock_fall -clock altera_reserved_tck -min $tdo_out_min [get_ports {altera_reserved_tdo}]
}

proc set_tdo_timing_spec_when_drive_device { } {
    # TCO timing spec of tdi on the device driven by this tdo output
    # ---customize here---
    set next_device_tdi_tco_max 10.0
    set next_device_tdi_tco_min 10.0

    # tdi delay on the PCB depends on the trace length from JTAG 10-pin 
    # header to FPGA on board. In general on the PCB, the signal travels 
    # at the speed of ~160 ps/inch (1000 mils = 1 inch).
    # ---customize here---
    set tdo_trace_max 0.5
    set tdo_trace_min 0.1

    set tdo_out_max [expr $next_device_tdi_tco_max + $tdo_trace_max + [get_tck_delay_max]]
    set tdo_out_min [expr $next_device_tdi_tco_min + $tdo_trace_min + [get_tck_delay_min]]

    #TDO latches at the rising edge of TCK per standard
    set_output_delay -add_delay -clock altera_reserved_tck -max $tdo_out_max [get_ports {altera_reserved_tdo}]
    set_output_delay -add_delay -clock altera_reserved_tck -min $tdo_out_min [get_ports {altera_reserved_tdo}]
}

proc set_optional_ntrst_timing_spec { } {
    # ntrst is an optional JTAG pin to asynchronously reset the device JTAG controller.
    # There is no path from this pin to any FPGA core fabric.
    if { [get_collection_size [get_ports -nowarn {altera_reserved_ntrst}]] > 0 } {
        set_false_path -from [get_ports {altera_reserved_ntrst}]
    }
}

set_jtag_timing_constraints

1 Constrained under Intel® Quartus® Prime Standard Edition by default.
2 Unconstrained under Intel® Quartus® Prime Pro Edition unless you use a variation of the SDC example contained in the JTAG Signal Constraints template.