Hard Processor System Component Reference Manual: Agilex™ 5 SoCs

Download PDF
ID 813752
Date 11/10/2025
Public
Document Table of Contents
Document Table of Contents x
1. Introduction to the Agilex™ 5 Hard Processor System Component 2. Configuring the Agilex™ 5 Hard Processor System Component 3. Simulating the Agilex™ 5 HPS Component 4. Design Guidelines
1. Introduction to the Agilex™ 5 Hard Processor System Component x
1.1. Release Notes 1.2. Micro Processor Unit 1.3. Application Processor Subsystem 1.4. Peripheral Subsystem 1.5. CoreSight* Debug Components 1.6. Interconnect 1.7. FPGA Bridges 1.8. Introduction to the Agilex™ 5 Hard Processor System Component Revision History
1.1. Release Notes x
1.1.1. HPS IP 11.1.0 1.1.2. HPS IP 9.0.0 1.1.3. HPS IP 7.0.0 1.1.4. HPS IP 6.0.0 1.1.5. HPS IP 5.1.0 1.1.6. HPS IP 4.0.0
2. Configuring the Agilex™ 5 Hard Processor System Component x
2.1. Parameterizing the HPS Component 2.2. HPS-FPGA Interfaces 2.3. SDRAM 2.4. HPS Clocks, Reset, Power 2.5. I/O Delays 2.6. Pin Mux and Peripherals 2.7. Generating and Compiling the HPS Component 2.8. Using the Address Span Extender Component 2.9. Configuring the Agilex™ 5 Hard Processor System Component Revision History
2.2. HPS-FPGA Interfaces x
2.2.1. General 2.2.2. HPS FPGA Bridges 2.2.3. DMA Controller Interface 2.2.4. Interrupts
2.2.1. General x
2.2.1.1. Enable MPU Standby and Event Signals 2.2.1.2. Enable General Purpose Signals 2.2.1.3. Enable Debug APB* Interface 2.2.1.4. Enable System Trace Macrocell (STM) Hardware Events 2.2.1.5. Enable SWJ-DP JTAG Interface 2.2.1.6. Enable FPGA Cross Trigger Interface 2.2.1.7. Enable AMBA* Trace Bus (ATB)
2.2.2. HPS FPGA Bridges x
2.2.2.1. FPGA to HPS Subordinate 2.2.2.2. FPGA to SDRAM Subordinate 2.2.2.3. HPS to FPGA Manager 2.2.2.4. Lightweight HPS to FPGA Manager
2.2.4. Interrupts x
2.2.4.1. FPGA-to-HPS 2.2.4.2. HPS-to-FPGA
2.3. SDRAM x
2.3.1. Configurations for HPS IP 2.3.2. Configurations for HPS EMIF IP 2.3.3. Graphical Connections of HPS to HPS-EMIF 2.3.4. Configuration when using ECC 2.3.5. Configuration of HPS EMIF Calibration Settings 2.3.6. Supported Memory Protocols Among Device Families 2.3.7. IO96 Bank and Lane Usage for HPS EMIF 2.3.8. Quartus Report of I/O Bank Usage 2.3.9. Debugging with the External Memory Interface Debug Toolkit
2.4. HPS Clocks, Reset, Power x
2.4.1. Input Clocks 2.4.2. PLL Clocks 2.4.3. Power and Resets
2.4.1. Input Clocks x
2.4.1.1. External Clocks 2.4.1.2. FPGA-to-HPS Clocks 2.4.1.3. Peripheral FPGA Clocks
2.4.2. PLL Clocks x
2.4.2.1. Main PLL Output 2.4.2.2. Peripheral PLL Output 2.4.2.3. MPU Clocks 2.4.2.4. NOC Clocks 2.4.2.5. Peripheral Clocks 2.4.2.6. HPS-to-FPGA User Clocks
2.4.3. Power and Resets x
2.4.3.1. Power Configurations 2.4.3.2. Reset Signals
2.6. Pin Mux and Peripherals x
2.6.1. Pin Mux GUI 2.6.2. EMAC PTP Interface 2.6.3. HPS I/O Open Drain 2.6.4. HPS I/O Locations
2.6.1. Pin Mux GUI x
2.6.1.1. Auto-Place IP 2.6.1.2. Advanced
2.6.1.1. Auto-Place IP x
2.6.1.1.1. Options for NAND, SDMMC, TRACE, TPIU, EMAC
2.6.1.1.1. Options for NAND, SDMMC, TRACE, TPIU, EMAC x
2.6.1.1.1.1. HPS IO Placement Priority
2.6.1.2. Advanced x
2.6.1.2.1. Advanced IP Placement 2.6.1.2.2. Advanced FPGA Placement
3. Simulating the Agilex™ 5 HPS Component x
3.1. Simulation Flows 3.2. Simulating the Agilex™ 5 HPS Example Design Across Bridges (H2F, LWH2F, F2SDRAM, and F2H) 3.3. Simulating the Agilex™ 5 HPS Component Revision History
3.1. Simulation Flows x
3.1.1. Setting Up the HPS Component for Simulation 3.1.2. Generating the HPS Simulation Model in Platform Designer
3.2. Simulating the Agilex™ 5 HPS Example Design Across Bridges (H2F, LWH2F, F2SDRAM, and F2H) x
3.2.1. Use Cases 3.2.2. Configuring the Interfaces 3.2.3. Implementing Example Design Callback Procedure 3.2.4. Running the Testbench
3.2.1. Use Cases x
3.2.1.1. Default Use Case 3.2.1.2. Test Array IP Use Case
3.2.4. Running the Testbench x
3.2.4.1. Questa*-Altera® FPGA Edition Example 3.2.4.2. Synopsys* VCS Example 3.2.4.3. Cadence Xcelium* Example
4. Design Guidelines x
4.1. HPS System Reset Considerations 4.2. Design Guidelines Revision History
1. Introduction to the Agilex™ 5 Hard Processor System Component
2. Configuring the Agilex™ 5 Hard Processor System Component
3. Simulating the Agilex™ 5 HPS Component
4. Design Guidelines

3.2.4.2. Synopsys* VCS Example

Follow these steps to run the example design in the VCS simulation environment.
  1. Run cd <path>/EXAMPLE/intel_agilex_5_soc_0_example_design/sim/ command.
  2. Set up your developer environment with the proper simulator resources.
  3. Use sh hps_example_design_tb_run_vcs.sh command.
  4. Go to ./ed_sim/sim/synopsys/vcsmx/transcript directory to view your results files.

    An example of test summary is provided below.

    # @11970.000ns*********************************************
# @11970.000ns************** TEST SUMMARY *****************
# @11970.000ns*********************************************
# HPS2FPGA Test -- PASS
# LWHPS2FPGA Test -- PASS
# F2SDRAM Test -- PASS
# FPGA2HPS Test -- PASS
# HPS Example Design Simulation passed!
# 
# @11970.000ns**************** END OF TEST ****************
# 
# ** Note: $finish    : ../../../hps_example_design_tb.sv(1076)
#    Time: 11970 ns  Iteration: 1  Instance: /hps_example_design_tb
# 1
# Break in Module hps_example_design_tb at ../../../hps_example_design_tb.sv line 1076
Level Two Title