1G/2.5G/5G/10G Multirate Ethernet PHY IP User Guide: Agilex™ 3 and Agilex™ 5 FPGAs and SoCs

Download PDF
ID 813667
Date 8/04/2025
Public
Document Table of Contents
Document Table of Contents x
1. About the 1G/2.5G/5G/10G Multirate Ethernet PHY IP for Agilex™ 3 and Agilex™ 5 Devices 2. Getting Started 3. Functional Description 4. Parameter Settings for 1G/2.5G/5G/10G Multirate Ethernet PHY IP 5. Interface Signals 6. Configuration Registers 7. Debug Checklist 8. 1G/2.5G/5G/10G Multirate Ethernet PHY IP User Guide: Agilex™ 3 and Agilex™ 5 FPGAs and SoCs Archives 9. Document Revision History for the 1G/2.5G/5G/10G Multirate Ethernet PHY IP User Guide: Agilex™ 3 and Agilex™ 5 FPGAs and SoCs
1. About the 1G/2.5G/5G/10G Multirate Ethernet PHY IP for Agilex™ 3 and Agilex™ 5 Devices x
1.1. Release Information 1.2. Features 1.3. Device Family Support 1.4. Device Speed Grade Support 1.5. Resource Utilization
2. Getting Started x
2.1. Introduction to IP 2.2. Installing and Licensing IPs 2.3. Specifying the IP Core Parameters and Options 2.4. Generated File Structure 2.5. Simulating IPs 2.6. Integrating Your IP Core in Your Design
2.2. Installing and Licensing IPs x
2.2.1. Altera FPGA IP Evaluation Mode
2.6. Integrating Your IP Core in Your Design x
2.6.1. Adding the GTS System PLL Clocks IP
3. Functional Description x
3.1. Architecture 3.2. Dynamic Reconfiguration Flow 3.3. Clocking and Reset Sequence 3.4. Timing Constraints 3.5. Operation Speed Switching 3.6. USXGMII 3.7. Fmax Requirement
3.1. Architecture x
3.1.1. 2.5G, 1G/2.5G, 1G/2.5G/10G (MGBASE) 3.1.2. 10M/100M/1G/2.5G/5G/10G (USXGMII) 3.1.3. 1G/2.5G/10G MGBASE PCS only
3.2. Dynamic Reconfiguration Flow x
3.2.1. RTL Generation using Dynamic Reconfiguration IP
3.2.1. RTL Generation using Dynamic Reconfiguration IP x
3.2.1.1. Step 1: Generating the 1G/2.5G/5G/10G Multirate Ethernet PHY IP 3.2.1.2. Step 2: QSF settings and Dynamic Reconfiguration (DR) profile assignments 3.2.1.3. Step 3: RTL Generation using Quartus® Prime Pro Edition Tool 3.2.1.4. Step 4: Instantiate the IP top file with the GTS Dynamic Reconfiguration Controller IP
3.3. Clocking and Reset Sequence x
3.3.1. Clocking 3.3.2. Reset Sequence
4. Parameter Settings for 1G/2.5G/5G/10G Multirate Ethernet PHY IP x
4.1. Core Configuration 4.2. Analog Parameters
5. Interface Signals x
5.1. Clock Signals 5.2. Reset Signals 5.3. Serial Interface Signals 5.4. Avalon Memory-Mapped Interface Signals 5.5. XGMII Signals 5.6. GMII Signals 5.7. PHY Status Signals 5.8. Transceiver Mode and Operating Speed Signals 5.9. Transceiver Status and Reconfiguration Signals 5.10. GTS Reset Sequencer Signals 5.11. Dynamic Reconfiguration Controller Interface Signals
5.6. GMII Signals x
5.6.1. 1G/2.5G/10G MGBASE PCS Only PMA Interface
6. Configuration Registers x
6.1. Register Map 6.2. PHY Registers
7. Debug Checklist x
7.1. Pre-Debugging Process 7.2. Clock Frequency 7.3. Recommended Reset Handling 7.4. Signals for Signal Tap
1. About the 1G/2.5G/5G/10G Multirate Ethernet PHY IP for Agilex™ 3 and Agilex™ 5 Devices
2. Getting Started
3. Functional Description
4. Parameter Settings for 1G/2.5G/5G/10G Multirate Ethernet PHY IP
5. Interface Signals
6. Configuration Registers
7. Debug Checklist
8. 1G/2.5G/5G/10G Multirate Ethernet PHY IP User Guide: Agilex™ 3 and Agilex™ 5 FPGAs and SoCs Archives
9. Document Revision History for the 1G/2.5G/5G/10G Multirate Ethernet PHY IP User Guide: Agilex™ 3 and Agilex™ 5 FPGAs and SoCs

8. 1G/2.5G/5G/10G Multirate Ethernet PHY IP User Guide: Agilex™ 3 and Agilex™ 5 FPGAs and SoCs Archives

For the latest and previous versions of this user guide, refer to 1G/2.5G/5G/10G Multirate Ethernet PHY IP User Guide: Agilex™ 3 and Agilex™ 5 FPGAs and SoCs. If an IP or software version is not listed, the user guide for the previous IP or software version applies.

Level Two Title