F-Tile 1G/2.5G/5G/10G Multirate Ethernet PHY Intel® FPGA IP User Guide

Download PDF
ID 720989
Date 11/29/2023
Public
Document Table of Contents
Document Table of Contents x
1. About the F-Tile 1G/2.5G/5G/10G Multirate Ethernet PHY Intel® FPGA IP User Guide 2. 1G/2.5G/5G/10G Multirate Ethernet PHY Intel® FPGA IP Overview 3. Getting Started 4. Functional Description 5. 1G/2.5G/5G/10G Multirate Ethernet PHY Intel® FPGA IP Parameters 6. Interface Signals 7. Configuration Registers 8. F-Tile 1G/2.5G/5G/10G Multirate Ethernet PHY Intel® FPGA IP User Guide Archive 9. Document Revision History for the F-Tile 1G/2.5G/5G/10G Multirate Ethernet PHY Intel® FPGA IP User Guide
2. 1G/2.5G/5G/10G Multirate Ethernet PHY Intel® FPGA IP Overview x
2.1. Release Information 2.2. Features 2.3. Device Family Support 2.4. Device Speed Grade Support 2.5. Resource Utilization
3. Getting Started x
3.1. Introduction to Intel® FPGA IP 3.2. Installing and Licensing Intel® FPGA IPs 3.3. Specifying the IP Core Parameters and Options 3.4. Generated File Structure 3.5. Simulating Intel® FPGA IPs 3.6. Upgrading the 1G/2.5G/5G/10G Multirate Ethernet PHY Intel® FPGA IP Core 3.7. Integrating Your IP Core in Your Design
3.2. Installing and Licensing Intel® FPGA IPs x
3.2.1. Intel® FPGA IP Evaluation Mode
3.7. Integrating Your IP Core in Your Design x
3.7.1. Adding the F-Tile Reference and System PLL IP
4. Functional Description x
4.1. Clocking and Reset Sequence 4.2. Timing Constraints 4.3. Operation Speed Switching 4.4. IEEE 802.3 Clause 37 Auto-Negotiation 4.5. USXGMII 4.6. IEEE 1588 Precision Time Protocol
4.1. Clocking and Reset Sequence x
4.1.1. Clocking 4.1.2. Reset
6. Interface Signals x
6.1. Clock Signals 6.2. Reset Signals 6.3. Serial Interface Signals 6.4. Avalon® Memory-Mapped Interface Signals 6.5. XGMII Signals 6.6. Transceiver Status and Transceiver Clock Status Signals 6.7. Reconfiguration Signals 6.8. Operating Speed and Status Signals
7. Configuration Registers x
7.1. Register Map 7.2. PHY Registers
1. About the F-Tile 1G/2.5G/5G/10G Multirate Ethernet PHY Intel® FPGA IP User Guide
2. 1G/2.5G/5G/10G Multirate Ethernet PHY Intel® FPGA IP Overview
3. Getting Started
4. Functional Description
5. 1G/2.5G/5G/10G Multirate Ethernet PHY Intel® FPGA IP Parameters
6. Interface Signals
7. Configuration Registers
8. F-Tile 1G/2.5G/5G/10G Multirate Ethernet PHY Intel® FPGA IP User Guide Archive
9. Document Revision History for the F-Tile 1G/2.5G/5G/10G Multirate Ethernet PHY Intel® FPGA IP User Guide

3.6. Upgrading the 1G/2.5G/5G/10G Multirate Ethernet PHY Intel® FPGA IP Core

The Intel® Quartus® Prime software alerts you when your IP core is not upgraded to the current version. Click Project > Upgrade IP Components to identify and upgrade the IP cores. To successfully upgrade the IP core, you must ensure that the file structure of your project that was generated by an older version of the software is preserved. Failure to upgrade IP cores can result in a mismatch between the IP core variation and the current supporting libraries.

Intel verifies that the current version of the Intel® Quartus® Prime software compiles the previous version of each IP core. The Intel® FPGA IP Release Notes reports any verification exceptions. Intel does not verify the compilation of IP cores older than the previous release.

Figure 5. Upgrading IP Components in Project Navigator


Level Two Title