F-Tile DisplayPort IP Design Example User Guide

Download PDF
ID 709308
Date 12/01/2025
Public
Document Table of Contents
Document Table of Contents x
1. DisplayPort IP Design Example Quick Start Guide 2. DisplayPort IP Design Examples 3. Display Stream Compression (DSC) Support 4. HDCP Over DisplayPort Design Example 5. Document Revision History for F-Tile DisplayPort IP Design Example User Guide
1. DisplayPort IP Design Example Quick Start Guide x
1.1. Directory Structure 1.2. Hardware and Software Requirements 1.3. Generating the Design 1.4. Simulating the Design 1.5. Compiling and Testing the Design 1.6. DisplayPort IP Design Example Parameters
1.5. Compiling and Testing the Design x
1.5.1. Regenerating ELF File
2. DisplayPort IP Design Examples x
2.1. Agilex™ 7 F-Tile DisplayPort SST Parallel Loopback Design Features 2.2. Agilex™ 7 F-Tile DisplayPort SST TX-only Design Features 2.3. Agilex™ 7 F-Tile DisplayPort SST RX-only Design Features 2.4. Design Components 2.5. Clocking Scheme 2.6. Interface Signals and Parameters 2.7. Simulation Testbench
4. HDCP Over DisplayPort Design Example x
4.1. High-bandwidth Digital Content Protection (HDCP) 4.2. HDCP Over DisplayPort Design Example Architecture 4.3. Nios® V Processor Software Flow 4.4. Design Walkthrough 4.5. Protection of Encryption Key Embedded in FPGA Design 4.6. Debug Guidelines
4.4. Design Walkthrough x
4.4.1. Setting Up the Hardware 4.4.2. Generating the Design 4.4.3. Including HDCP Production Keys 4.4.4. Compiling the Design 4.4.5. Viewing the Results
4.4.3. Including HDCP Production Keys x
4.4.3.1. Storing Plain HDCP Production Keys in the FPGA (Support HDCP Key Management = 0) 4.4.3.2. Storing Encrypted HDCP Production Keys in the External Flash Memory or EEPROM (Support HDCP Key Management = 1)
4.4.3.1. Storing Plain HDCP Production Keys in the FPGA (Support HDCP Key Management = 0) x
4.4.3.1.1. HDCP Key Mapping from DCP Key Files 4.4.3.1.2. hdcp1x_tx_kmem.v and hdcp1x_rx_kmem.v files 4.4.3.1.3. hdcp2x_rx_kmem.v file 4.4.3.1.4. hdcp2x_tx_kmem.v file
4.4.3.2. Storing Encrypted HDCP Production Keys in the External Flash Memory or EEPROM (Support HDCP Key Management = 1) x
4.4.3.2.1. Altera® KEYENC 4.4.3.2.2. Key Programmer
4.5. Protection of Encryption Key Embedded in FPGA Design x
4.5.1. Security Considerations
4.6. Debug Guidelines x
4.6.1. HDCP Status Signals 4.6.2. Modifying HDCP Software Parameters 4.6.3. Frequently Asked Questions (FAQ)
1. DisplayPort IP Design Example Quick Start Guide
2. DisplayPort IP Design Examples
3. Display Stream Compression (DSC) Support
4. HDCP Over DisplayPort Design Example
5. Document Revision History for F-Tile DisplayPort IP Design Example User Guide

1.5. Compiling and Testing the Design

Figure 5. Compiling and Simulating the Design
To compile and run a demonstration test on the hardware example design, follow these steps:
  1. Ensure hardware example design generation is complete.
  2. Launch the Quartus® Prime Pro Edition software and open <project>/quartus/agi_dp_demo.qpf.
  3. Click Processing > Start Compilation.
  4. After successful compilation, the Quartus® Prime Pro Edition software generates a .sof file in your specified directory.
  5. Connect the DisplayPort RX connector on the supported FMC daughter card to an external DisplayPort source, such as the graphics card on a PC.
  6. Connect the DisplayPort TX connector on the supported FMC daughter card to a DisplayPort sink device, such as a video analyzer or a PC monitor.
  7. Ensure all switches on the development board are in default position.
  8. Configure the selected Agilex™ 7 F-Tile device on the development board using the generated .sof file (Tools ➤ Programmer ).
  9. The DisplayPort sink device displays the video generated from the video source.

Section Content
Regenerating ELF File

Related Information
Level Two Title