Intel Agilex® 7 Configuration User Guide

ID 683673
Date 10/09/2023
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents

3.1.7.4.3. PFL II IP Recommended Design Constraints for using CFI Flash

Create a FLASH_CLK clock

Example below assigns CFI flash clock pin (flash_clk) to the flash clock. You constrain the flash_clk pin only when using burst mode.

create_generated_clock -name FLASH_CLK -source [get_ports {clk_50m_max5}] [get_ports {flash_clk}]

Set output delay for output pins

Example below sets the output delay for CFI flash output pins.

set flash_data_tracemax 0.250
set flash_data_tracemin 0.000
set flash_clk_tracemax 0.250
set flash_clk_tracemin 0.000
set flash_Tsu 3.500
set flash_Th 2.000
set flash_out_max_dly [expr $flash_data_tracemax + $flash_Tsu - $flash_clk_tracemin]
set flash_out_min_dly [expr $flash_data_tracemin - $flash_Th - $flash_clk_tracemax]

#Note: For normal mode, the clock is referred to input pfl_clk clock(clk_50m_max5) of PFL II IP. 
#If burst mode is used, the clock is referred to flash clock of PFL II IP.   

set_output_delay -add_delay -max -clock [get_clocks {clk_50m_max5}] \
$flash_out_max_dly [get_ports {flash_nce[0] flash_nce[1] flash_noe flash_nwe flash_addr[*] flash_data[*]}]

set_output_delay -add_delay -min -clock [get_clocks {clk_50m_max5}] \
$flash_out_min_dly [get_ports { flash_nce[0] flash_nce[1] flash_noe flash_nwe flash_addr[*] flash_data[*]}]

#Only need to constraint flash_advn pin when using burst mode.
set_output_delay -add_delay -max -clock [get_clocks { FLASH_CLK }] $flash_out_max_dly [get_ports {flash_nadv}]
set_output_delay -add_delay -min -clock [get_clocks { FLASH_CLK }] $flash_out_min_dly [get_ports {flash_nadv}]

Set input delay for input pins

Example below sets the input delay for CFI flash data.

# For Normal Mode
set flash_noe_tracemax 0.250
set flash_noe_tracemin 0.000
set flash_tco_max 7.000
set flash_tco_min 0.000
set normal_in_max_dly [expr $flash_data_tracemax + $flash_tco_max + $ flash_noe_tracemax]
set normal_in_min_dly [expr $flash_data_tracemin + $flash_tco_min + $ flash_noe_tracemin]

set_input_delay -clock { clk_50m_max5 } -max $normal_in_max_dly [get_ports {flash_data[*]}]
set_input_delay -clock { clk_50m_max5 } -min $normal_in_min_dly [get_ports {flash_data[*]}]
# For Burst mode
set flash_tco_max 5.500
set flash_tco_min 2.000
set burst_in_max_dly [expr $flash_data_tracemax + $flash_tco_max + $flash_clk_tracemax]
set burst_in_min_dly [expr $flash_data_tracemin + $flash_tco_min + $flash_clk_tracemin]

set_input_delay -clock { FLASH_CLK } -max $burst_in_max_dly [get_ports {flash_data[*]}]
set_input_delay -clock { FLASH_CLK } -min $burst_in_min_dly [get_ports {flash_data[*]}]