Intel® Simics® Simulator for Intel® FPGAs: Agilex™ 5 Virtual Platform User Guide

Download PDF
ID 786901
Date 5/09/2025
Public
Document Table of Contents
Document Table of Contents x
1. About This Document 2. Agilex™ 5 Intel® Simics® Virtual Platforms 3. Agilex™ 5 Universal Virtual Platform Component Intel® Simics® Models 4. Running a Simulation with the Agilex™ 5 HPS Model 5. Supported Use Cases 6. Troubleshooting Issues When Migrating Software from Intel® Simics® to Hardware A. Document Revision History for Intel Simics Simulator for Intel FPGAs Agilex 5 Virtual Platform User Guide
1. About This Document x
1.1. Terminology 1.2. List of Acronyms
2. Agilex™ 5 Intel® Simics® Virtual Platforms x
2.1. Agilex™ 5 Universal Virtual Platform
2.1. Agilex™ 5 Universal Virtual Platform x
2.1.1. Agilex™ 5 Universal Virtual Platform Overview 2.1.2. Agilex™ 5 Universal Virtual Platform User-Configurable Parameters 2.1.3. Agilex™ 5 Universal Virtual Platform Key Capabilities
2.1.1. Agilex™ 5 Universal Virtual Platform Overview x
2.1.1.1. Agilex™ 5 HPS Component 2.1.1.2. HPS Subsystem Component 2.1.1.3. FPGA Fabric Design 2.1.1.4. qsys_top Component 2.1.1.5. FPGA Component 2.1.1.6. Board Component 2.1.1.7. System Component 2.1.1.8. Target Script
2.1.3. Agilex™ 5 Universal Virtual Platform Key Capabilities x
2.1.3.1. Boot-To-Operating System Prompt 2.1.3.2. Basic Ethernet 2.1.3.3. CPU Power-On and Boot Core Selection 2.1.3.4. Reset Flow 2.1.3.5. General Purpose I/O (GPIO) Loopback 2.1.3.6. USB Disks Hot-Plug Support 2.1.3.7. On-Chip Memory IP FPGA Fabric Example Design 2.1.3.8. FPGA-to-HPS Bridges 2.1.3.9. Exercising Peripheral Subsystem in FPGA Fabric Design 2.1.3.10. USB Controller Host/Device Mode Configuration 2.1.3.11. Agilex™ 5 HPS Component and Stepping Silicon Features Selection 2.1.3.12. UART1/UART2 Serial Console Selection
3. Agilex™ 5 Universal Virtual Platform Component Intel® Simics® Models x
3.1. Agilex™ 5 HPS Intel® Simics® Model 3.2. Virtual Platform HPS Subsystem Components 3.3. Virtual Platform qsys_top Components 3.4. Virtual Platform Board Components 3.5. Modeling Support Limitations
3.1. Agilex™ 5 HPS Intel® Simics® Model x
3.1.1. Agilex™ 5 HPS Intel® Simics® Model Architecture 3.1.2. PSS Subsystem Components 3.1.3. MPU and APS Subsystem 3.1.4. MPFE Subsystem 3.1.5. Additional Agilex™ 5 HPS Components 3.1.6. Agilex™ 5 B0 Features Support
3.2. Virtual Platform HPS Subsystem Components x
3.2.1. External Memory Interface (EMIF) 3.2.2. Security Device Manager (SDM)
3.3. Virtual Platform qsys_top Components x
3.3.1. FPGA Fabric
3.4. Virtual Platform Board Components x
3.4.1. Marvel EMAC PHY 3.4.2. SD Card Device Limitations 3.4.3. ONFI NAND Memory Device 3.4.4. SPI Flash Device 3.4.5. AT24Cxx EEPROM Device 3.4.6. I3C Device 3.4.7. USB Disk Device 3.4.8. Intel® Simics® Text Console
4. Running a Simulation with the Agilex™ 5 HPS Model x
4.1. Prerequisites 4.2. Intel® Simics® Simulation Setup for the Agilex™ 5 Device 4.3. Starting the Simulation 4.4. Getting Device Information from the Intel® Simics® Model
1. About This Document
2. Agilex™ 5 Intel® Simics® Virtual Platforms
3. Agilex™ 5 Universal Virtual Platform Component Intel® Simics® Models
4. Running a Simulation with the Agilex™ 5 HPS Model
5. Supported Use Cases
6. Troubleshooting Issues When Migrating Software from Intel® Simics® to Hardware
A. Document Revision History for Intel Simics Simulator for Intel FPGAs Agilex 5 Virtual Platform User Guide

3.4.2. SD Card Device

This is an SD card device model based on SD (v3.00) protocol specifications. The SD card is connected to the SD/eMMC controller via the Combo PHY interface. The following commands are supported:

Table 24.  SD Card Device Commands
Command Class Commands Supported

Class 0: Basic command.

CMD0, CMD2, CMD3S, CMD4, CMD7, CMD8, CMD9. CMD10, CMD11, CMD12, CMD13, CMD15.

Class 2: Block-oriented read commands.

CMD19S, CMD20, CMD16, CMD17, CMD18, CMD21, CMD23.

Class 4: Block-oriented write commands.

CMD24, CMD25.

Class5: Erase commands.

CMD32, CMD33, CMD38.

Class 8: Application specific commands.

CMD55, ACMD6, ACDM13, ACDM22, ACDM23, ACDM41, ACDM42, ACDM51.

Class 9: I/O read/write commands (SDIO commands).

CMD52, CMD53.

Class 10: Switch function commands.

CMD6S.

Limitations

  • Model limited to SD v3.00 protocol specification.
  • While you can set the SD card size to any size you like, you cannot change the SD card size after the virtual platform is instantiated.
  • Only the commands indicated in the earlier table are supported.
  • Device lock/unlock operation (password protection) not supported.
  • The SD card is fixed to the SD mode (no SDIO).

Component: sd_card

Level Two Title