Stratix® 10 High-Speed LVDS I/O User Guide

Download PDF
ID 683792
Date 5/16/2025
Public
Document Table of Contents
Document Table of Contents x
1. Stratix® 10 High-Speed LVDS I/O Overview 2. Stratix® 10 High-Speed LVDS I/O Architecture and Features 3. Stratix 10 High-Speed LVDS I/O Design Considerations 4. Stratix® 10 High-Speed LVDS I/O Implementation Guides 5. LVDS SERDES Intel® FPGA IP References 6. Stratix® 10 High-Speed LVDS I/O User Guide Archives 7. Document Revision History for the Stratix® 10 High-Speed LVDS I/O User Guide
1. Stratix® 10 High-Speed LVDS I/O Overview x
1.1. Stratix® 10 LVDS SERDES Usage Modes 1.2. Stratix® 10 LVDS Channels Support 1.3. Stratix® 10 GPIO Banks, SERDES, and DPA Locations
2. Stratix® 10 High-Speed LVDS I/O Architecture and Features x
2.1. Stratix® 10 LVDS SERDES I/O Standards Support 2.2. LVDS Transmitter Programmable I/O Features 2.3. SERDES Circuitry 2.4. Differential Transmitter in Stratix® 10 Devices 2.5. Differential Receiver in Stratix® 10 Devices
2.2. LVDS Transmitter Programmable I/O Features x
2.2.1. Programmable Pre-Emphasis 2.2.2. Programmable Differential Output Voltage
2.4. Differential Transmitter in Stratix® 10 Devices x
2.4.1. Transmitter Blocks in Stratix® 10 Devices 2.4.2. Serializer Bypass for DDR and SDR Operations
2.5. Differential Receiver in Stratix® 10 Devices x
2.5.1. Receiver Blocks in Stratix® 10 Devices 2.5.2. Receiver Modes in Stratix® 10 Devices
2.5.1. Receiver Blocks in Stratix® 10 Devices x
2.5.1.1. DPA Block 2.5.1.2. Synchronizer 2.5.1.3. Data Realignment Block (Bit Slip) 2.5.1.4. Deserializer
2.5.2. Receiver Modes in Stratix® 10 Devices x
2.5.2.1. Non-DPA Mode 2.5.2.2. DPA Mode 2.5.2.3. Soft-CDR Mode
3. Stratix 10 High-Speed LVDS I/O Design Considerations x
3.1. PLLs and Clocking for Stratix® 10 Devices 3.2. Source-Synchronous Timing Budget 3.3. Guideline: LVDS SERDES IP Core Instantiation 3.4. Guideline: LVDS SERDES Pin Pairs for Soft-CDR Mode 3.5. Guideline: LVDS Transmitters and Receivers in the Same I/O Bank 3.6. Guideline: LVDS SERDES Limitation for Stratix® 10 GX 400, SX 400, and TX 400
3.1. PLLs and Clocking for Stratix® 10 Devices x
3.1.1. Clocking Differential Transmitters 3.1.2. Clocking Differential Receivers 3.1.3. Guideline: LVDS Reference Clock Source 3.1.4. Guideline: Use PLLs in Integer PLL Mode for LVDS 3.1.5. Guideline: Use High-Speed Clock from PLL to Clock LVDS SERDES Only 3.1.6. Guideline: Pin Placement for Differential Channels 3.1.7. LVDS Interface with External PLL Mode
3.1.6. Guideline: Pin Placement for Differential Channels x
3.1.6.1. PLLs Driving Differential Transmitter Channels 3.1.6.2. PLLs Driving DPA-Enabled Differential Receiver Channels 3.1.6.3. PLLs Driving DPA-Enabled Differential Receiver and Transmitter Channels in LVDS Interface Spanning Multiple I/O Banks
3.1.7. LVDS Interface with External PLL Mode x
3.1.7.1. IOPLL IP Signal Interface with LVDS SERDES IP 3.1.7.2. IOPLL Parameter Values for External PLL Mode 3.1.7.3. Connection between IOPLL IP and LVDS SERDES IP in External PLL Mode
3.2. Source-Synchronous Timing Budget x
3.2.1. Differential Data Orientation 3.2.2. Differential I/O Bit Position 3.2.3. Transmitter Channel-to-Channel Skew 3.2.4. Receiver Skew Margin for Non-DPA Mode
3.2.2. Differential I/O Bit Position x
3.2.2.1. Differential Bit Naming Conventions
3.2.4. Receiver Skew Margin for Non-DPA Mode x
3.2.4.1. RSKM Equation 3.2.4.2. Example: RSKM Calculation
3.5. Guideline: LVDS Transmitters and Receivers in the Same I/O Bank x
3.5.1. Using the Duplex Feature 3.5.2. Using an External PLL
4. Stratix® 10 High-Speed LVDS I/O Implementation Guides x
4.1. LVDS SERDES Intel® FPGA IP 4.2. LVDS SERDES IP Initialization and Reset 4.3. LVDS SERDES Intel® FPGA IP Timing 4.4. LVDS SERDES Intel® FPGA IP Design Examples 4.5. IP Migration Flow for Arria® V, Cyclone® V, and Stratix® V Devices
4.1. LVDS SERDES Intel® FPGA IP x
4.1.1. Release Information 4.1.2. LVDS SERDES Intel® FPGA IP Features 4.1.3. LVDS SERDES IP Core Functional Modes 4.1.4. LVDS SERDES IP Core Functional Description
4.1.4. LVDS SERDES IP Core Functional Description x
4.1.4.1. Serializer 4.1.4.2. DPA FIFO 4.1.4.3. Bitslip 4.1.4.4. Deserializer 4.1.4.5. Clock Phase Alignment
4.2. LVDS SERDES IP Initialization and Reset x
4.2.1. Initializing the LVDS SERDES IP in Non-DPA Mode 4.2.2. Initializing the LVDS SERDES IP in DPA Mode 4.2.3. Resetting the DPA 4.2.4. Word Boundaries Alignment
4.2.4. Word Boundaries Alignment x
4.2.4.1. Aligning Word Boundaries
4.3. LVDS SERDES Intel® FPGA IP Timing x
4.3.1. I/O Timing Analysis 4.3.2. FPGA Timing Analysis 4.3.3. Timing Analysis for the External PLL Mode 4.3.4. Timing Closure Guidelines for Internal FPGA Paths 4.3.5. Guideline: Use Clock Phase Alignment Block to Improve Timing Closure
4.3.1. I/O Timing Analysis x
4.3.1.1. Obtaining RSKM Report 4.3.1.2. Obtaining TCCS Report
4.4. LVDS SERDES Intel® FPGA IP Design Examples x
4.4.1. LVDS SERDES IP Synthesizable Quartus® Prime Design Examples 4.4.2. LVDS SERDES IP Simulation Design Example 4.4.3. Combined LVDS SERDES IP Transmitter and Receiver Design Example 4.4.4. LVDS SERDES IP Dynamic Phase Shift Design Example
4.5. IP Migration Flow for Arria® V, Cyclone® V, and Stratix® V Devices x
4.5.1. Migrating Your ALTLVDS_TX and ALTLVDS_RX IP Cores
5. LVDS SERDES Intel® FPGA IP References x
5.1. LVDS SERDES Intel® FPGA IP Parameter Settings 5.2. LVDS SERDES Intel® FPGA IP Signals 5.3. Comparison of LVDS SERDES Intel® FPGA IP with Stratix® V SERDES
5.1. LVDS SERDES Intel® FPGA IP Parameter Settings x
5.1.1. LVDS SERDES Intel® FPGA IP General Settings 5.1.2. LVDS SERDES Intel® FPGA IP PLL Settings 5.1.3. LVDS SERDES Intel® FPGA IP Receiver Settings 5.1.4. LVDS SERDES Intel® FPGA IP Transmitter Settings 5.1.5. LVDS SERDES IP Core Clock Resource Summary
5.1.3. LVDS SERDES Intel® FPGA IP Receiver Settings x
5.1.3.1. Receiver Input Clock Parameters Setup
5.1.4. LVDS SERDES Intel® FPGA IP Transmitter Settings x
5.1.4.1. Setting the Transmitter Output Clock Parameters
1. Stratix® 10 High-Speed LVDS I/O Overview
2. Stratix® 10 High-Speed LVDS I/O Architecture and Features
3. Stratix 10 High-Speed LVDS I/O Design Considerations
4. Stratix® 10 High-Speed LVDS I/O Implementation Guides
5. LVDS SERDES Intel® FPGA IP References
6. Stratix® 10 High-Speed LVDS I/O User Guide Archives
7. Document Revision History for the Stratix® 10 High-Speed LVDS I/O User Guide

5.1.1. LVDS SERDES Intel® FPGA IP General Settings

Table 25.  General Settings Tab
Parameter Value Description
Duplex Feature
  • On
  • Off
 Turn on to allow transmitter and receiver channels in the same I/O bank.
  • The number of transmitter and receiver channels in the same I/O bank is the same.
  • The number of channels is limited to 11 transmitters and 11 receivers.
  • Use external PLL option is disabled.
Functional mode
  • TX
  • RX Non-DPA
  • RX DPA-FIFO
  • RX Soft-CDR

Specifies the functional mode of the interface.

The TX option is not available if you turn on the Duplex Feature option. In duplex mode, transmitter channels are created by default.

Number of channels
  • Duplex Feature = Off
    • TX—1 to 72
    • RX Non-DPA—1 to 24
    • RX DPA-FIFO—1 to 24
    • RX Soft-CDR—1 to 12
  • Duplex Feature = On
    • 1 to 11

Specifies the number of serial channels in the interface.

  • If you use a dedicated reference clock for the TX, RX non-DPA, or RX DPA-FIFO, you must use one of the channels for the refclk pin. Use a dedicated reference clock to reduce jitter.
  • If you use a transmitter output clock, you must use one of the channels for the tx_outclock pin.

For an LVDS RX design, place the refclk pin on the same I/O bank as the receiver.

For an LVDS TX design:

  • For an interface with less than 23 channels (standalone), each interface requires a refclk pin on the same I/O bank.
  • For an interface with more than 23 channels, channels 23 to 71 can share one refclk input.

In Duplex Feature mode, this value specifies the number of channels each for the transmitter and receiver. For example, if you specify 11 channels, the IP core uses 22 channels in the I/O bank.

Data rate 150.0 to 1600.0

Specifies the data rate (in Mbps) of a single serial channel. The value is dependent on the Functional mode parameter settings.

SERDES factor 3, 4, 5, 6, 7, 8, 9, and 10

Specifies the serialization rate or deserialization rate for the LVDS interface.
Use backwards-compatible port names
  • On
  • Off
 Turn on to use legacy top-level names that are compatible with the ALTLVDS_TX and ALTLVDS_RX IPs.
Use the CPA block for improved periphery-core timing
  • On
  • Off
 Turn on to improve timing closure between the periphery and core. The IP core uses the clock phase alignment (CPA) block to phase-align the core clock and load enable clock. The option is available for any selectable SERDES factor if:
  • Functional mode is TX, RX Non-DPA, or RX DPA-FIFO.
  • Desired tx_outclock phase shift (degrees) parameter is a multiple of 180°.
Level Two Title