JESD204B Intel® FPGA IP User Guide

Download PDF
ID 683442
Date 7/20/2023
Public
Document Table of Contents
Document Table of Contents x
1. JESD204B IP Quick Reference 2. About the JESD204B Intel® FPGA IP 3. Getting Started 4. JESD204B IP Functional Description 5. JESD204B IP Deterministic Latency Implementation Guidelines 6. JESD204B IP Debug Guidelines 7. JESD204B Intel® FPGA IP User Guide Archives 8. Document Revision History for the JESD204B Intel® FPGA IP User Guide
2. About the JESD204B Intel® FPGA IP x
2.1. Release Information 2.2. Device Family Support 2.3. Datapath Modes 2.4. IP Variation 2.5. JESD204B IP Configuration 2.6. Channel Bonding 2.7. Performance and Resource Utilization
2.5. JESD204B IP Configuration x
2.5.1. Run-Time Configuration
3. Getting Started x
3.1. Introduction to Intel® FPGA IP Cores 3.2. Installing and Licensing Intel® FPGA IP Cores 3.3. Intel® FPGA IP Evaluation Mode 3.4. Upgrading IP Cores 3.5. IP Catalog and Parameter Editor 3.6. Design Walkthrough 3.7. JESD204B Design Examples 3.8. JESD204B IP Design Considerations 3.9. JESD204B Intel® FPGA IP Parameters 3.10. JESD204B IP Component Files 3.11. JESD204B IP Testbench
3.6. Design Walkthrough x
3.6.1. Creating a New Intel® Quartus® Prime Project 3.6.2. Parameterizing and Generating the IP 3.6.3. Compiling the JESD204B IP Core Design 3.6.4. Programming an FPGA Device
3.8. JESD204B IP Design Considerations x
3.8.1. Integrating the JESD204B IP in Platform Designer 3.8.2. Pin Assignments 3.8.3. Adding External Transceiver PLLs 3.8.4. Timing Constraints For Input Clocks
3.11. JESD204B IP Testbench x
3.11.1. Generating and Simulating the IP Testbench 3.11.2. Testbench Simulation Flow
3.11.1. Generating and Simulating the IP Testbench x
3.11.1.1. Generating the Testbench Simulation Model 3.11.1.2. Simulating the IP Testbench
4. JESD204B IP Functional Description x
4.1. Transmitter 4.2. Receiver 4.3. Operation 4.4. Clocking Scheme 4.5. Reset Scheme 4.6. Signals 4.7. Registers
4.1. Transmitter x
4.1.1. TX Data Link Layer 4.1.2. TX PHY Layer
4.1.1. TX Data Link Layer x
4.1.1.1. TX CGS 4.1.1.2. TX ILAS 4.1.1.3. User Data Phase
4.2. Receiver x
4.2.1. RX Data Link Layer 4.2.2. RX PHY Layer
4.2.1. RX Data Link Layer x
4.2.1.1. RX CGS 4.2.1.2. Frame Synchronization 4.2.1.3. Frame Alignment 4.2.1.4. Lane Alignment 4.2.1.5. ILAS Data 4.2.1.6. Initial Lane Synchronization
4.3. Operation x
4.3.1. Operating Modes 4.3.2. Scrambler/Descrambler 4.3.3. SYNC_N Signal 4.3.4. Link Reinitialization 4.3.5. Link Startup Sequence 4.3.6. Error Reporting Through SYNC_N Signal
4.3.1. Operating Modes x
4.3.1.1. Subclass 0 Operating Mode 4.3.1.2. Subclass 1 Operating Mode 4.3.1.3. Subclass 2 Operating Mode
4.4. Clocking Scheme x
4.4.1. Device Clock 4.4.2. Link Clock 4.4.3. Local MultiFrame Clock 4.4.4. Clock Correlation 4.4.5. Transceiver Calibration Clock Source
4.5. Reset Scheme x
4.5.1. Reset Sequence 4.5.2. ADC–FPGA Subsystem Reset Sequence 4.5.3. FPGA–DAC Subsystem Reset Sequence
4.6. Signals x
4.6.1. Transmitter Signals 4.6.2. Receiver Signals
4.7. Registers x
4.7.1. Register Access Type Convention 4.7.2. Transmitter Registers 4.7.3. Receiver Registers
5. JESD204B IP Deterministic Latency Implementation Guidelines x
5.1. SYSREF Guidelines 5.2. Constraining Incoming SYSREF Signal 5.3. Programmable RBD Offset 5.4. Programmable LMFC Offset 5.5. Maintaining Deterministic Latency during Link Reinitialization
6. JESD204B IP Debug Guidelines x
6.1. Clocking Scheme 6.2. JESD204B Parameters 6.3. SPI Programming 6.4. Converter and FPGA Operating Conditions 6.5. Signal Polarity and FPGA Pin Assignment 6.6. Creating a Signal Tap Debug File to Match Your Design Hierarchy 6.7. Debugging JESD204B Link Using System Console
6.6. Creating a Signal Tap Debug File to Match Your Design Hierarchy x
6.6.1. Removing Irrelevant Signals and Adding E-Tile PHY Signals
1. JESD204B IP Quick Reference
2. About the JESD204B Intel® FPGA IP
3. Getting Started
4. JESD204B IP Functional Description
5. JESD204B IP Deterministic Latency Implementation Guidelines
6. JESD204B IP Debug Guidelines
7. JESD204B Intel® FPGA IP User Guide Archives
8. Document Revision History for the JESD204B Intel® FPGA IP User Guide

6.2. JESD204B Parameters

The parameters in both the FPGA and ADC should be set to the same values. For example, when you set K = 32 on the FPGA, set the converter's K value to 32 as well. Scrambling does not affect the link initialization in the CGS and ILAS phases but in the user data phase. When scrambling is enabled on the ADC, the FPGA descrambling option has to be turned on using the "Enable scramble (SCR)" option in the JESD204B IP core Platform Designer parameter editor. When scrambling is enabled on the FPGA, the DAC descrambling has to be turned on too.

Check these items:

  • Turn off the scrambler and descrambler options as needed.
  • Use single lane configuration and K = 32 value to isolate multiple lane alignment issue.
  • Use Subclass 0 mode to isolate SYSREF related issues like setup or hold time and frequency of SYSREF pulse.
Level Two Title